Our Saw-tooth Wave Jig is a new type of energy saving and high efficient gravity separation equipment and developed based on the traditional Sine Wave Jig. The difference between Saw-tooth Wave Jig and Sine Wave Jig is that the pulsation curve for jigging is saw-tooth wave shape, with speedy upward flow and slow downward flow. Descriptions Our Saw-tooth Wave Jig is a new type of energy saving and high efficient gravity separation equipment and developed based on the traditional Sine Wave Jig. The difference between Saw-tooth Wave Jig and Sine Wave Jig is that the pulsation curve for jigging is saw-tooth wave shape, with speedy upward flow and slow downward flow. Bed layer is elevated integrally and slowly dropped with a long effective loose time, allowing significant increase of handling capacity for unit screen surface, decrease of lower limit of grain size recovery and large save of make-up water for under size fraction. In practice, contrast of Saw-tooth Wave Jig and Sine Wave Jig shows up raises of recovery of Saw-tooth Wave Jig: Sn:3.01%, W:5.5%, Pb:1.63%, Zn:2.04%. Advantages and Characteristics 1 High capacity 2 High concentration ratio and high recovery 3 Easy to install, operate and maintain 4 The pulsation curve is saw-tooth wave shape facilitate heavy mineral to settling 5 Saving water 30-40% than ordinary jig 6 The pulsation speed very easy adjusted by regulator 7 Can achieve a good result in processing such as placer gold, tungsten,iron, tin, hematite, copper, tantalum-niobium, titanium, manganese, barite, zirconium, chrome and gemstone etc
Trommel screens provide a simple, efficient and economical solution to upgrade a wide rang of material and optimize the subsequent process steps of recovery. This method of screening helps to reduce operating and investment cost and to increase product quality, while allowing rapid and large volume processing. Descriptions Material feeds into the drum, is lifted up by the rotation as it falls back down. This action is repeated with each revolution along the length of the drum. The finer material passes through the screen openings while the larger material tumbles towards its eventual exit at the rear of the drum. The trommel screens provide a simple, efficient and economical solution to upgrade a wide rang of material and optimize the subsequent process steps of recovery. This method of screening helps to reduce operating and investment cost and to increase product quality, while allowing rapid and large volume processing. This material is then passed on to the downstream process equipment which can be in various forms such as centrifugal concentrator, spirals, jigs etc. Advantages and characteristics 1 economical and efficient solution for screening; 2 heavy duty trommel drum with lifters at the front to facilitate material break up; 3 screen replaceable for different mesh sizes; 4 multilayer screens; 5 easily change screen plates; 6 high efficiency and big capacity; 7 unique screen design, result in higher capacities, longer screen life and no material clogging; 8 heavy duty feed hopper; 9 discharge chute; 10 gear drive mechanism. Main technical parameters
Descriptions The rotary scrubber is an autogenous rotating drum scrubber, utilizing pebbles and rocks within the feed source to fracture and disintegrate clays, agglomerates and soft oxides. The scrubber spins slowly, similar to a giant washing machine. It churns the fines and oversize and water together, vigorously breaking up the soil matrix as well as liberating the target mineral from tough clay, schistâ??s and rock. Disintegrated material is homogeneously slurried within the drum, whilst the autogenous load is retained within the drum by reverse flights located at the drum discharge end. Slurry and washed oversize overflows the drum discharge throat to the concentric exit trommels. This material is then passed on to the downstream process equipment which can be in various forms such as centrifugal concentrator, spiral chute, jig etc. Advantages and Characteristics 1. Designed to break up alluvial gravels, clays and sand; 2. High capacity and high scrubbing power; 3. The long drum of the scrubber retains material for longer, more vigorous washing for complete separation; 4. Thickening type steel plate for the drum; 5. Heavy duty bearing, gear and roller; 6. Wearable screen at the exit of drum for screening; 7. One high output electrical motor driving a gear system providing efficient torque; 8. Adjustable rotary speed; 9. The water with high pressure flushed the inwall of drum; 10. Can accept material up to 230mm.
Description Log washer is mainly used to wash the manganese ore, iron ore, phosphate and other minerals, it is usually used to clean and separate the silt and stains from manganese ore, iron ore and other low-grade mineral. Also it suitable for scrubbing material which contains tough insoluble clays, conglomerates or soft stone. This machine drive the spiral stirring shaft depends on speed reducer and rotate in different directions, and the minerals which enter the tank were washed by water and stir strongly by blade. The sewage was overflowed at the end of tank, the cleaned minerals were lifted up along the blade and discharged at the beginning of tank. Advantages and Characteristics 1 Durable washing and conveying paddles 2 Fabricated with heavy duty shafts 3 Oversize bearings and gears
Description It is one kind of feeder as collection ore belt type conveyor for the ball mill, because the structure is simple, easy to operation, less power consumption, the feeding quantity can be evenly controlled, so it obtains widespread application. Main Technical Parameters Model Entrance size (mm) Exit size(mm) Swinging (mm) Swinging frequency (mm) Max Particle size (mm) Productive capacity (t/h) Motor (kw) Weight (kg) 300 300 300 300 300 125 0~90 68 100 8 1.1 213 400 400 400 400 400 50~150 0~170 47 35 12 1.1 272 600 600 600 600 600 150~150 0~206 45.5 50 25 1.5 558
Description The trough feeder used for feed massive material to receiving machinery from hopper, it is widely used to feed large size material (undressed ore and so on) into primary crusher of metallurgy, mine, chemical industry, building, dressing, coal ,and so on. Main Technical Parameters Model Entrance size (mm) Exit size (mm) Swinging (mm) Swinging frequency (mm) Max Particle size(mm) Productive capacity (t/h) Motor (kw) Weight (kg) 400*400 400*400 400*400 12 18.2 100 25-30 1.1 535 600*500 600*500 600*500 10-50 38.9 200 10-50 4 1054 980*1240 980*1240 900*800 20-50 23.7 350 36-90 7.5 1676
Description Rock hammer crusher can crush ore which is below 50mm or the tailings, middlings which in the uncompleted ore. And break up the useful metal from the ore, depending on the requirement of factory, it can crush the mineral particles in 1 to 180 mesh, and separate them in the shaking table. They are suitable for the small factory, and same times can take place of ball mill in some degree, Easy installation, easy operation, less investment, fast effect. The rock hammer crusher consist of rotor which with hammer, and the rotor consist of spindle, disk, pin and hammer. The motor drives the rotor to rotate at a high speed through the belt, the material enter the machine through the feeding port the rotating hammers with high rotation speed are crushing them, the small size mineral was discharge through the sieve and the large size still was crush and beat in the sieve until the crushed products meeting the required size can be discharged by the outlet and become the final products. Main Technical Parameters Model Capacity (T/h) Feeding Size (mm) Discharge Size (mm) Power at user option Motor (Kw) Diesel 200 500 1-2 50 1.8 15-18 24 300 500 3-6 50 1.8 18-22 30 400 600 5-10 50 1.8 25-30 45
Saw-tooth Wave Laboratory Jig is a new type of energy saving and high efficient gravity separation equipment and developed based on the traditional Sine Wave Jig. The difference between Saw-tooth Wave Jig and Sine Wave Jig is that the pulsation curve for jigging is saw-tooth wave shape, with speedy upward flow and slow downward flow. Advantages and Characteristics 1 High capacity 2 High concentration ratio and high recovery 3 Easy to install, operate and maintain 4 The pulsation curve is saw-tooth wave shape facilitate heavy mineral to settling 5 Saving water 30-40% than ordinary jig 6 The pulsation speed very easy adjusted by regulator 7 Can achieve a good result in processing such as placer gold, tungsten,iron, tin, hematite, copper, tantalum-niobium, titanium, manganese, barite, zirconium, chrome and gemstone etc Main Technical Parameters Model Hutch Diaphragm Feeding Size (mm) Makeup water (m3/t) Makeup water pressure (Mpa) Capacity (t/h) Power (kw) Dimensions (mm) Weight (Kg) Shape Area (m2) Stroke (mm) Frequency of stroke (r/min) JT0.57-1 Trapezoid 0.57 8.5 12 10 17 12-21 80-180
DescriptionsDouble deck shaking table is widely used for tungsten, tin, tantalum and niobium, gold, iron, manganese and other metals, ferrous metals, nonferrous metals, precious metals and other minerals and coal sorting. Traditional shaker covers an area of large, relatively low processing capacity,cost increases, double-shaker covers an area of inconvenience to deal with a large amount of equipment, low cost, Shaker is available in the double-sweep the election, featuring various operations, sorting coarse sand (2-0.5 mm), fine sand (0.5-0.74), sludge (0.074) different grain level, The same bed with hyperbolic rocker mechanism, the spring box in the shaker box, the crankshaft, rod, springs, rocker and so increase the size, material unchanged. The lower bed sharing a set of lower bed slope adjustment device used in shake liner support. Technical Specifications Model Unit DL4500/1850 DL3000/1320 Bed Size mm 4500/1850/1560 3000/1320/1100 Stroke mm 6-8 6-8 Frequency of stroke /min 240-380 210-320 Slope o 0-10 0-10 Feed size mm 0.02-2 0.02-2 Feed density % 10-30 10-30 Water t/h 0.8-1.4 0.6-1.2 Power kw 1.5 1.5 Capacity t/h 2.5-3.5 (coarse sand) 2.5-3 (coarse sand) t/h 1.6-2.5 (find sand) 0.8-2.5 (find sand) Overall dimensions mm 5600/1850/1560 4100/1320/1560 Weight kg 1650 1550
XFG series hanging cell flotation machine is used in the geological, metallurgical, building materials, chemical industry, mining and scientific research institutions, laboratory for stirring scrubbing, separating and cleaning minor samples. It uses the technology of frequency conversion stepless speed regulation, impeller, digital display, accurate adjustment.
1. Product performance standards: api 8a and sy / t5235. 2. Environmental conditions used sucker rod elevator A) allows the use at a temperature of -18, ~ 70, . B) meet the harsh conditions of oil field operations. 3. Sucker rod elevator's types: reed. 4. Material requirements: kava body is made of high-quality high-strength steel, handles made of high quality alloy forged steel. 5. Sucker rod elevator main technical parameters: A) applicable rod outer diameter: 5 / 8in ~ 1 1 / 8in. B) maximum load: 15t (135kn), 25t (225kn). 6. Sucker rod elevator major quality control requirements: 1) the chemical composition of each batch of material compliance with the relevant standards. 2) body 10% radiographic flaw detection, high stress area to meet the requirements of grade â?¡ gb / t5677, the remaining parts of the meet gb , level requirements / t5677's. 3) mechanical properties body of not less than: rm, 640 pma, rp0.2, 540 pma, z, 15%, a, 25%, akv, 42j (-20, ). 4) product 10% for 1.5 times the testimony load test. 5) all parts for magnetic particle testing, high stress area to meet the requirements of grade â?¡ gb / t9444, the remaining parts of the meet gb , level requirements / t9444's. 6) the main products from raw materials to the carrier using the site dating back the whole process. 7. Sucker rod elevator structure diagram and parts list below: Cdq (s) sucker rod elevator structure diagram.
Api 9a drilling wire line rope Construction: 1x3;1x7;1x12;1x19;6x7+fc/iwrc ;6x12+7fc;6x19+fc/iwrc;6x24+7fc;6x37 6x25fi+fc/iwrc;6x26ws;6x36+fc/iwrc, ws;8x19s+fc/iwrc;19x7 Quality assurance system: A. Strict selection of domestic high-quality hard-line to control theh product quality : using domestic the best materials, such as bomco wire rope company and shagang group. B. Perfect rod testing equipment: spectrometer, tensile testing machine, metallographic analyzer, high and low times metallographic analyzer.Testing for detection rod into the plant chemical costs, tissue properties and mechanical properties. C. With perfect wire rope and wire rope testing equipment: medium and small tensile testing machine, torsion testing machine, bending test machine, steel strands-tension fatigue testing machine, wire bending fatigue testing machine, fatigue testing Machine wire rope, wire rope pre-tensioning equipment, etc, we can test the the performance of wire rope. D. Wire rope production process using the advanced north america, germany management models. Meanwhile, the introduction of technology also brings the foreign advanced production organization and management mode such as quality track record, pre-production equipment, tooling, mold and other inspection records, processing management. E. Product organizational processes in according to gb/t19001 and apispecq1 for quality control. F. Corresponding to each batch of steel wire rope in accordance with rigorous testing standards, including process and final inspection. G. Approved by the american petroleum institute api monogram. And had passed the iso9000 certification.
Product Description BOP parts that we supply all come from original manufacturers, they are 100% interchangeable. BOP PART NAME: top sealing, front sealing, pipe ram, blind ram, slip ram, shear ram, spherical packer, bonnet, piston, shell. APPLY TO BELOW BOP: Brand: SHENKAI BOP. RONGSHENG BOP ETC OTHER FAMOUS BRAND BOP Type: Annular BOP, Single Ram BOP, Double Ram BOP, Shear Ram BOP Technical parameter Specification: 1. Standad: API 16 A and ISO 9001 2. Rated Pressure: 2000Psi to 15000Psi(14-17 Mpa) 3. Size: Nominal Bore: 7-1/16" to 21-1/4" (179.4mm to 539.75mm) 4. Type: Shear Ram/ Pipe Ram/ Variable Bore Ram 5. Usage : Single Ram BOP/ Double Ram BOP/ Three Ram BOP 6.Brand:Shenkai and Rongsheng. 7.Imitate: Camaron and Shaffer 8.U type and SH type Characters of BOP pare parts: In the structure, it is divided into annular blowout preventer with spherical plastic core, annular blowout preventer with cone-shaped plastic core, and blowout preventer with tube-shaped plastic core. Annular BOP top cap and housing are connected by bolts or claw blocks. Blowout preventer with spherical plastic core and dust-proof ring. Performance characteristics: reasonable structure, easy operation, long life of plastic core, adapt to a wide range, capable to seal pipe string with nominal paths from 0-DN in ans shapes, better performance by combining with ran blowout preventer in the use. Working of BOP pare parts: When wells must be sealed in case of kicks high pressure (10.5Mpa) oil from control systems enters into close-cavity under piston from housing oil outlet, to promote plastic core moving upward along ball surface, so that bearing tendons move closer to each other to moce the rubber between them to the center of wellhead so as to seal drilling tools or fully seal wellhead. In opening , hydraulic pressure oul enters into open-cavity above piston from housing oul inlet, to push piston moving downwards , so that plastic will reset with its own elasticity, wellhead will be open.
Downhole well drilling tool Roller reamer The Roller Reamer is designed for various reaming operation but particularly for various reaming operation but particularly for stabilization purpose when drilling in very abrasive formations. It will fit hole sizes ranging from â??6 to 28â?�. In addition, each body by simple adjustment of blocks and proper selection of cutters, will suit a wide range of hole sizes. Three different types(T, F, and B) of cutters are offered: Type T: Milled, machined with hardfaced sharp teeth for soft formations. Type F: Milled, machined with hardfaced flat teeth, for medium hard formations. Type B: Equipped with pressed-in tungsten carbide buttons, for hard formations.
Aimed at pump rod break, stripping, piston dropping without opening oil drainage unit during operation of oil well, no ordinary oil drainage achievement in heavy oil and paraffin troubled well, environment pollution and so on, rotary oil drainage unit is the patent product (patent no. Zl2005200845803) specially designed and developed. It has advantages of simple structure, easy operation and reliable oil drainage,
Product overviews Double slip connector is a tool to quickly connect downhole tools to coiled tubing. Double slip connector is different from conventional connector, double slip lock rings make sure the tool lock to the coiled tubing, no need for buckle. Two slip rings can share the load and improve the reliability, two o-rings to seal tubing string. Advantages Easy to installation, and quick to connect. The slip lock ring is special designed, which improves the reliability Large load capability Double o-ring seal Functions Double slip connector suit for all coiled tubing downhole tools Load high torque, can connect to mud motor High strength connection application Remove one rock ring as single connect
Feed opening (mm):200*350 Max.Feeding size (mm):180 Adjusting range of discharge opening (mm):18-70 Processing capacity (t/h):3-10 Rotation speed of eccentric shaft (r/min):260 Motor power (kw):11 Total weight (t)1.5 Dimensions(l*w*h)(mm)1000*870*990
Performance characteristics: Bag Filter is widely applied for dust collection applications in mining industry, chemical industry, pharmaceutical industry, and the production of flour, glass, metallurgy, mine, cement, building materials, etc. The bag filter is made up of the top chest, middle chest, bottom chest, dust exhauster, and jet cleaning system. There is spray tube and air outlet at the top chest. The middle box consists of perforated plate, venturi tube, filter bag, keel, pulse valve and gas cleaning system. The bottom chest is comprised of ash bucket, air inlet, access door, ash exhauster (which is composed of rotary dust valve or spiral conveyer) It could be made of carbon steel or stainless steel upon request. Dust collector is generally used with a temperature less than 12C. Customized dust collector for usage at high temperatures (less 23C) is also available.
This rotary cooler equipment can quickly cool higher-temperature of granular compound fertilizer directly Approximately to normal atmospheric temperature, which is convenient for timely and quick packing and Prevents compound fertilizer from forming block during store. It can achieve adverse Flow cooling, which can reduce pollution and improve working environment. It has many characteristics such as reasonable structure, stable run, strong adaptability etc.. Features of cooler: 1.High cooling efficiency 2.Simple structure, low rate malfunction, convenient operation, low cost of maintenance, stable operation. 3.Wide usage, can be used for the drying of different materials in powder, granule, strip, lump, large elasticity Of operation. Output is allowed to have larger fluctuations in manufacturing, but not allowed to influence the Quality of the products. 4.Easy to install and remove Application range of cooler: 1. Chemical industry: ammonium sulfate, sodium sulphide, anfu powder, ammonium nitrate, Urea, oxalic acid, bichromate potassium, pvc, nitrophosphate fertilizer, fytic acid, Phosphate compound fertilizer. 2. Food industry: glucose, salt, sugar, vitamin malted milk, granular sugar. 3. Mining products: ceramic sand , coal, coal slime, manganese ore, limestone, pyrite, peat, etc. 4. Others: iron powder, flat soybean
Performance characteristics: Bag Filter is widely applied for dust collection applications in mining industry, chemical industry, pharmaceutical industry, and the production of flour, glass, metallurgy, mine, cement, building materials, etc. The bag filter is made up of the top chest, middle chest, bottom chest, dust exhauster, and jet cleaning system. There is spray tube and air outlet at the top chest. The middle box consists of perforated plate, venturi tube, filter bag, keel, pulse valve and gas cleaning system. The bottom chest is comprised of ash bucket, air inlet, access door, ash exhauster (which is composed of rotary dust valve or spiral conveyer) It could be made of carbon steel or stainless steel upon request. Dust collector is generally used with a temperature less than 120C. Customized dust collector for usage at high temperatures (less 230C) is also available.
