Molybdenum spraying wire: Molybdenum spraying wire is used as a thin coating on the surface of automobile components subjected to wear, such as piston rings, gearbox synchromesh parts, selector forks, etc. Molybdenum spraying wire is also sprayed onto machine parts such as bearing for repair purposes. Furthermore, molybdenum spray wire is applied as an intermediate layer. Dia. 0.03mm-2.0mm Fine Molybdenum wire: The molybdenum wire is principally used in the high-temperature field of molybdenum furnace and radio tube outlets, also in thinning the molybdenum filament, and the molybdenum rod in heating materials for high-temperature furnace, and side-bracket/bracket/outlets wire for heating materials. 2000 meters/spool or coil.
Pure nickel wire properties: Material: Pure Nickel, Purity:99.5%~99.9% 1: Nickel wire has Good resistance to corrosion in acids and alkalis and is most useful under reducing conditions. 2: Nickel wire has Outstanding resistance to caustic alkalis up to and including the molten state. 3: Nickel wire is Virtually immune to inter granular attack above 315C, chlorates must be kept to a minimum. 4: In acid, alkaline and neutral salt solutions, Nickel wire shows good resistance, but in oxidising salt solutions severe attack will occur. Wire diameter: 0.05mm-2.5mm, 10 gauge to 24 gauge, 0.101897 inch to 0.020101 inch. Fine Nickel Wire: We are specialized in manufacture of Fine Nickel Wires. They are made with high standard and qulity controll system. Purity:99.5%~99.9%. Fine Nickel wire diameter range from 0.04mm to 0.10mm, with high precision anf high purity. Thin Nickel Wire Manufacture: The thin nickel wire are made by advanced vacuum melting process. And by forging, rolling, annealing and drawing. To manufacture this very thin nickel wire, very strict quality controll system and the best material are used. Every step shall be done carefully during manufacture, especially the annealling process. 3 to 5 kgs/spool or coil.
Product name: nickel-chromium heating wire, strip. Product model:Cr20Ni80/ Cr30Ni70/ Cr15Ni60/ GH1140/Cr20Ni35/Cr20Ni30 Specifications: wire: 0.05 --- 10 mm Strip: (0.05 - 0.1) (5 - 250) mm Bar: 12 --- 30 mm Flat Yarn: 0.025 (0.4 - 4) mm. Introduction: Nickel-chromium alloy material is austenitic alloy, high temperature strength than the high-iron-chromium alloy material with high and stable resistance, corrosion resistance, good oxidation resistance of the surface, no distortion at high temperature, good viscosity, elongation than the iron-chromium alloy is 50%, processing prone to breaking, long after the plastic is better, do not become brittle after cooling, ease of repair after damage, regeneration of the alloy is good, is an industrial furnace, metallurgy, machinery, electrical appliances, aircraft, automotive, military and other industries producing heating elements and resistance elements preferred material. 3 kgs /spool.
Monel 400 Alloy Wire: Monel 400 Alloy Wire is corrosion resisting, such as resistant to sea water and steam at high temperatures, resistant to salt and caustic solutions. Meanwhile, it exhibits characteristic like high strength.Monel 400 Alloy Wire has low corrosion rate in flowing brackish or seawater while performing excellent resistance to stress-corrosion cracking in most freshwaters Wire Diameter: 0.05mm-5.0mm, 4Gauge to 24 Gauge, 0.002 Inch to 0.2043 Inch Monel K-500 Alloy Wire: Monel K500 Alloy Wire is one kind of the nickel-copper alloy Alloy Wire. Monel K500 Alloy Wire combines the excellent corrosion resistance of Monel 400 Alloy Wire with the added advantage of greater strength and hardness. Alloy K-500 Alloy Wire has approximately three times the yield strength and double the tensile strength when compared with alloy 400. When in the age-hardened condition, Wire Diameter: 0.05mm-5.0mm, 4Gauge to 24 Gauge, 0.002 Inch to 0.2043 Inch. 3 to 5 kgs/spool, coil.
