Submersible water pumps for mining, deep well pump, centrifugal pump, stainless steel pump Model:200QJ20-30/2 Flow: 20m3/h Head: 30m Power: 3kw Material:Cast iron/stainless steel Impeller material:Cast Iron/stainless steel Pressure:Low Pressure Warranty:12 Months Color:Blue Place of Origin: ,China (Mainland) Deep well submersible water pump Overview: deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/ Deep well submersible water pump structure&model meaning 1. Submersible electric pump is composed of five parts: water pump, submersible motor, water line, waterproof cable and control switch. Water pump belongs to single suction multistage vertical centrifugal pump. 2. Submersible motor adopts water-filled wet structure, internal chamber was filled with water for cooling the motor and lubricating the bearing. In the operation, due to the changes of temperature, the pressure of the filled water in the internal chamber also changes, it can be automatically regulated by pressure-regulating unit in the lower part of motor. 3. For preventing the sand getting into the motor, the sand-preventing unit including sand and skeleton oil-sealed was installed in the upper part of motor, the whole motor was sealed tightly. 4. There are water injection hole and exhaust hole in the upper part of the motor and discharge hole in the lower part. 5. There are thrust bearing and thrust collar, mainly for sustaining remnant axial force of pump and the empty weight of motor's rotor. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/ Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/
Submersible water pumps , deep well pump, centrifugal pump, stainless steel pump Model: 200QJ63-28/2 Flow: 63m3/h Head: 28m Power: 7.5kw Material:Cast iron/stainless steel Impeller material:Cast Iron/stainless steel Pressure:Low Pressure Warranty:12 Months Color:Blue Place of Origin: ,China (Mainland) Deep well submersible water pump Overview: deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/ Deep well submersible water pump structure&model meaning 1. Submersible electric pump is composed of five parts: water pump, submersible motor, water line, waterproof cable and control switch. Water pump belongs to single suction multistage vertical centrifugal pump. 2. Submersible motor adopts water-filled wet structure, internal chamber was filled with water for cooling the motor and lubricating the bearing. In the operation, due to the changes of temperature, the pressure of the filled water in the internal chamber also changes, it can be automatically regulated by pressure-regulating unit in the lower part of motor. 3. For preventing the sand getting into the motor, the sand-preventing unit including sand and skeleton oil-sealed was installed in the upper part of motor, the whole motor was sealed tightly. 4. There are water injection hole and exhaust hole in the upper part of the motor and discharge hole in the lower part. 5. There are thrust bearing and thrust collar, mainly for sustaining remnant axial force of pump and the empty weight of motor's rotor. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/ Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/
Submersible water pumps , deep well pump, centrifugal pump, stainless steel pump Model: 200QJ80-11/1 Flow: 80m3/h Head: 11m Power: 4kw Material:Cast iron/stainless steel Impeller material:Cast Iron/stainless steel Pressure:Low Pressure Warranty:12 Months Color:Blue Place of Origin: ,China (Mainland) http://www.dragonpump.com/products/submersible-pump/ Deep well submersible water pump Overview: deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/ Deep well submersible water pump structure&model meaning 1. Submersible electric pump is composed of five parts: water pump, submersible motor, water line, waterproof cable and control switch. Water pump belongs to single suction multistage vertical centrifugal pump. 2. Submersible motor adopts water-filled wet structure, internal chamber was filled with water for cooling the motor and lubricating the bearing. In the operation, due to the changes of temperature, the pressure of the filled water in the internal chamber also changes, it can be automatically regulated by pressure-regulating unit in the lower part of motor. 3. For preventing the sand getting into the motor, the sand-preventing unit including sand and skeleton oil-sealed was installed in the upper part of motor, the whole motor was sealed tightly. 4. There are water injection hole and exhaust hole in the upper part of the motor and discharge hole in the lower part. 5. There are thrust bearing and thrust collar, mainly for sustaining remnant axial force of pump and the empty weight of motor's rotor. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/ Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. http://www.dragonpump.com/products/qj-deep-well-submersible-pump/
Flow: 20m3/h Head: 64m Power: 7.5kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 20m3/h Head: 78m Power: 7.5kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 20m3/h Head: 91m Power: 9.2kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 20m3/h Head: 130m Power: 15kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 25m3/h Head: 78m Power: 9.2kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 25m3/h Head: 91m Power: 11kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 20m3/h Head: 104m Power: 11kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 20m3/h Head: 117m Power: 13kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 25m3/h Head: 65m Power: 7.5kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 20m3/h Head: 143m Power: 11kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 25m3/h Head: 78m Power: 9.2kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Flow: 10m3/h Head: 10m Power: 0.75kw Material: cast iron Medium: clean water Outlet dia: 50mm Speed: 2900r/min Voltage: 380V Phase: 3 phase/50Hz Color: Yellow Product overview: The series submersible sewage pump is mainly used for industry,agricultural,fishery,mine drainage,building construction, municipal environmental protection and tunnel construction etc. Trades to drain off soild particles with short fiber, confetti,sediment and so on. Or drain off software solids liquids. Such as mud,grey water, life wastewater, sewage and so on. The series submersible pump is the ideal equipment for agricultural irrigation,raising livestock and poultry manure pit,cleaning the silt of pool and construction site. Usage: Used for discharging waste water and other material with granular material, also it can be used for clean water and corrosive medium. Conditions of using: 1.The medium temperature should not be over 40oC ,PH:4-10. 2.The solid volume ratio of the medium should not be over 2%. 3.The kinematic viscosity of medium between 7*10-7m2/s---23*10-6 m2/s. 4.The density of the medium is 1.2*10 3kg/m3. 5.Centered on the impeller,underwater not more than 5m. Scope of application: 1. For discharging polluted waste water of factories and industries; 2. sewage discharge station of living quarters; 3. drainage system of municipal sewage treatment plant 4. drainage station of fire fighting system 5. waterworks equipment of running water factory 6. sewage discharge of hospitals and hotels 7. construction site of municipal engineering 8. matched equipment of exploration mine 9. country biogas digester 10.farm irrigation 11. other industries
Flow: 35m3/h Head: 5m Power: 0.75kw Material: cast iron Outlet dia: 80mm Speed: 2900r/min Voltage: 380V Phase: 3 phase/50Hz Color: Yellow Product overview: The series submersible sewage pump is mainly used for industry,agricultural,fishery,mine drainage,building construction, municipal environmental protection and tunnel construction etc. Trades to drain off soild particles with short fiber, confetti,sediment and so on. Or drain off software solids liquids. Such as mud,grey water, life wastewater, sewage and so on. The series submersible pump is the ideal equipment for agricultural irrigation,raising livestock and poultry manure pit,cleaning the silt of pool and construction site. Usage: Used for discharging waste water and other material with granular material, also it can be used for clean water and corrosive medium. Conditions of using: 1.The medium temperature should not be over 40oC ,PH:4-10. 2.The solid volume ratio of the medium should not be over 2%. 3.The kinematic viscosity of medium between 7*10-7m2/s---23*10-6 m2/s. 4.The density of the medium is 1.2*10 3kg/m3. 5.Centered on the impeller,underwater not more than 5m. Scope of application: 1. For discharging polluted waste water of factories and industries; 2. sewage discharge station of living quarters; 3. drainage system of municipal sewage treatment plant 4. drainage station of fire fighting system 5. waterworks equipment of running water factory 6. sewage discharge of hospitals and hotels 7. construction site of municipal engineering 8. matched equipment of exploration mine 9. country biogas digester 10.farm irrigation 11. other industries
Flow: 15m3/h Head: 26m Power: 2.2kw Material: cast iron Medium: clean water Outlet dia: 50mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage. Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province. The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence. Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Flow: 20m3/h Head: 64m Power: 7.5kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage.
Flow: 15m3/h Head: 65m Power: 5kw Material: cast iron Medium: clean water Outlet dia: 50mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage. .
Flow: 15m3/h Head: 80m Power: 7.5kw Material: cast iron Medium: clean water Outlet dia: 50mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage.
