DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Mercury, plastic products and chemical products..
For detailed pricing and further information, please contact us. Please note that at HYZH ENERGY, customer satisfaction is of utmost importance to us, and we are committed to providing you with the highest quality products and services. We are eager to work with you and help elevate your business to new heights. Best Regards, Fethi Ipek
metal platform Material: HT450 Weight: 600kg Manufacture process: Sand casting + machining
metal support Material: HT200 Weight: 20.7kg Manufacture process: Sand casting Description: Have the effect of support
metal joint Material: HT200 Weight: 40.2kg Manufacture process: Sand casting Description:the metal connecting piece
metal track Material: ZG28CrMnMo Weight:12.6kg Process:sand casting Description:Â the component parts of excavator and bulldozers caterpillar
Metal forging parts Material: Steel 45 Weight: 0.8-1.1kg Manufacture process: Forging Description:Forging is a manufacturing process involving the shaping of metal using localized compressive forces, Forging can produce a piece that is stronger than an equivalent cast or machined
metal instrument hull Material: 304 Weight: 0.57kg Manufacture process: Silica sol casting + casting Description: Protect the internal components of instrument
metal ROD CLV Material: 42CrMo Weight: 4.3kg Manufacture process: Precision casting + casting Description: Mainly used in industrial machinery
metal shovel teeth Material: 20CrNiMo Weight 2.2kg Process: Investment casting
metal three Joint Material: 304# Weight:2.65kg Process:Investment casting Description:Metal three joint is the connection of pipe fittings and pipeline
metal connecting Tube Material: 304# Weight:3.156kg Process:Investment casting Description:A tube which made of metal and used for connection
Metal PLUME JOINT PART Material:45# Weight:1.78kg Process: investment casting +machining Description: Metal connection
Metal PLUME JOINT PART Material:45# Weight:1.78kg Process: investment casting +machining Description: Metal connection
Material: Steel 45 Weight: 0.8-1.1kg Manufacture process: Forging Description:Forging is a manufacturing process involving the shaping of metal using localized compressive forces, Forging can produce a piece that is stronger than an equivalent cast or machined
Titanium metal powder Titanium sponge powder ti 99, 4%min, 99.2%min, 99%min, 97%min, 92%min Size: -30mesh, -60mesh, -100mesh, -200mesh, -325mesh 25kg, 50kg steel drums
Metal Lamp shade Material ADC12 Weight 1.78kg Manufacture Process Die Casting Description Chimney is not just a cover on the lamp together in order to make the light effect, still can prevent to get an electric shock, is also effective to protect our eye.
Metal PLUME JOINT PART Material:45# Weight:1.78kg Process: investment casting +machining Various designs and sizes are available OEM and ODM orders are welcome Perfect quality and competitive price Own the independent right of import and export
Sliver Mercury liquid hg 99.9% Please tell me how many flasks do you need ?then we will give you best price
