Uses Sample baking, drying and sample digestion test, is a necessary tool for geological, metallurgical, environmental protection, agriculture, grain and cooking oil, forestry, food, medical and health, biochemical and other laboratories, as well as teaching and research. Sample digestion before chemical analysis of soil, feed, plants, seeds, heavy metals, ore. It is an ideal equipment of sample pretreatment for analytical instruments such as AA, ICP, ICP-MS, and atomic fluorescence. It can also be used for pretreatment and acid removal treatment of microwave digestion. Main features 1.Corrosion resistance: Resist all kinds of acids: sulfuric acid, hydrochloric acid, nitric acid, hydrofluoric acid, perchloric acid, aqua regia and so on. Resist Alkali and a variety of corrosive gases. 2.High temperature resistance: Max. temperature 350 . (Plate temperature) 3.Temperature uniformity: The temperature difference of each point on the surface doesnt exceed ±2. Homogeneous batches of specimens (dozens of beakers) can reach boiling point at the same time. 4.Temperature control accurate: Can adjust temperature as desired, PID adjustment, temperature control accuracy: ±0.1. 5.Fast temperature rising: the time for room temperature rising to Max. temperature doesnt exceed 40 minutes, and the mean value is 6.9 seconds/. 6. No pollution: The plate hardness: Vickers hardness 20, density 3.02, no scratches, no dropping slags. 7. Temperature measuring by the plate: The temperature displayed by the instrument is actual temperature of the plate surface (operating temperature). 8. Two heat zones: The Max. temperature of A main heating zone is 350 , and Max. temperature of B secondary heating zone is 210 . 9. Shell material: High-quality ABS plastic wrap angle. 10. Reuse: The undamaged plate system can be reused. 11. Safety of use: Multilayer insulation protection, in case of equipment failure, the alarm will be light and sound and stop work immediately.
Janus Steel China, the manufacturer of anti corrosion clad steel plates and pipes of stainless steel, Nickel steel, Titanium steel and copper steel and other alloy steel for 20 years. Why choose us: 35-45 days delivery time Thickness of cladding steelï¼?2-15mmï¼? thickness of base steelï¼?6-300mm flexible payment model With 180 employees and 60 technicians, our annual output amounts to 30000 tons. Welcome you visiting! to be your reliable and stable supplier of clad steel.
A204 Grade A (A204Gr.A) steel is a molybdenum-alloy steel plate, intended particularly for welded boilers and other pressure vessels. Plates under ASTM A204 boiler steel standard are available in three grades having different strength levels: A204 Grade A; A204 Grade B; and A204 Grade C. The minimum yield strength of A204Gr.A steel is 255 MPa,tensile strength within 450-585 MPa. Equivalent: 15Mo3, 16Mo3 ASTM A204 boiler steel plate size Thickness: 3-250mm Width: 1220-4200mm Length: 3000-18000mm Notes: coil thickness �¢?�¤ 25mm Why Choose BBN Steel? 1. Competitive price and quality from our own factory 2. Approved by ISO9001, CE, SGS every year 3. Best online service with 24 hours reply 4. Deep processing service: cutting, welding, drilling, grinding, turning 5. Smooth production ability (3000tons/month)
GB/T1591 Q390A steel is high strength low alloy steel material. "Q" is the first letter of Chinese Pinyin: "qu fu dian", that means Yield Point, "390" is the minimum value of yield strength 390 MPa for steel thickness 16mm. "A" is the quality level. According to GB/T 15912008, Q390 material has 5 quality grades: Q390A, Q390B, Q390C, Q390D and Q390E. low alloy steel specification: Shapes: plates, sheet, angle, channel and round bar Thickness : 1.5-300mm Width: 1220-4200mm Length : 5000-18000mm Notes: coil thickness up to 25mm
Color coated steel coil Galvanized steel coil Pressed steel plate Tinplate steel coil or sheet Product packaging
A514 Grade E (A514 Gr.E) steel is a quenched and tempered high-strength alloy steel plate. ASTM A514 steel plate is characterized by high strength and good welding performance. It is mainly used in places requiring high tensile strength and high yield, such as lifting gears for engineering vehicles, large excavators, welded bridges, and racks for offshore platforms. BBN steel can supply A514 Grade E steel plates in thickness of 6inch (150mm). Main performance A514GrE quenched and tempered alloy steel has high strength, good fatigue resistance; high toughness and low brittle transition temperature; good cold forming performance and welding performance. In addition, it has good corrosion performance and certain wear resistance.
DIN17100 Grade RSt37-2 (1.0038) material is a structural quality carbon steel grade complies with DIN 17100: 1980. BBN STEEL company is able to produce this kind of structural steel product with various shapes: steel sections, plates, steel bars, steel strips, wide flats, seamless square hollow sections, and rectangular hollow sections. It is mainly being used for general mechanical engineering like welded structures, riveted structures and screwed structural components. RSt37-2 steelâ??s tensile strength is between 340 and 470 MPa. Standard: DIN 17100-1980 Steels for General Structural Purposes Quality Standard Grade: RSt37-2 Material number: 1.0038 Equivalent: Fe 360-BFN RSt37-2 strips and plates thickness: 1.5 mm to 350 mm MOQ: 1tons, we also can accept sample order. Shipment time: Within 15-20 working days after receiving deposit or L/C Export packing: waterproof paper, and steel strip packed, standard export seaworthy package. Capacity: 250,000 tons/year dincarbon.com
Supply form of 1.2311 steel DIN 1.2311 tool steel, we can supply the round bar, flat bar, plate, hexagonal and square block. Diameters can be sawn to your required lengths as one offs or multiple cut pieces. Rectangular pieces can be sawn from flat bar or plate to your specific sizes. Ground tool steel bar and precision ground steel plate can be supplied, providing a quality precision finished bar to tight tolerances. Applications of 1.2311 steel 1.2311 Tool steel is a German Die steel, the steel by super clean production process, pre hardened, showing the height of micro pure and excellent homogeneous structure, excellent polishing and light etching engraving. After heat treatment, processing and polishing performance is good, can be carried out, and can be processed, suitable for the surface treatment of chrome, material hardness even (to 400mm thick), good toughness, good mechanical processing performance. Gold microstructure is martensite and bainite structure. Main be applied to in zinc, aluminum, magnesium and its alloy die-casting mould ; Hot-pressing mold, all kinds of hot forging die; Metal extrusion die, die set.
GB/T 24186 NM500 abrasion resistant steel plates are high strength steel with high wear resistance. The Brinell hardness value of NM500 steel is 500 HBW. NM500 steel is mainly used to provide protection for wear-resistant occasions or parts. At the same time, NM500 abrasion resistant steel plates also have excellent machinability, especially welding performance. GB/T 24186� NM500 abrasion resistant steel plates are suitable for earth moving machinery, loading machinery, dredger, dump truck, conveying equipment, dump truck, blade, cutting crusher, waste treatment and recovery equipment, etc. application.
EN 10025-6 high strength steel plates S690Q, S690QL, S690QL1 are quenched and tempered steel plates, for which reason their low-temperature impact toughness has been greatly improved. With high yield strength and tensile strength, S690Q, S690QL, S690QL1 steel plates are widely used in coal mine machinery and engineering machinery. EN 10025-6 high strength steel plates S690Q, S690QL, S690QL1 are used to manufacture all kinds of construction machinery, such as drilling rigs, electric shovels, electric wheel dumpers, mining trucks, excavators, loaders, bulldozers, all kinds of cranes, coal mine hydraulic supports and other structural parts.
GB 6653 gas cylinder steel plates and strips are steel designed for manufacture of welded gas cylinders. The hot rolled GB 6653 gas cylinder steel plates and strips thickness range is 2-14mm, and the cold rolled GB 6653 gas cylinder steel plates and strips thickness range is 1.5-4mm. GB 6653 technical standard specifies the size, shape, weight and allowable deviation, technical requirements, test methods, inspection rules, packaging, marking and quality certificate of HP235 steel, HP265 steel, HP295 steel, HP325 steel, HP345 steel plates and strips for welded gas cylinders. Hot rolled GB 6653 gas cylinder steel plates and strips shall be delivered in hot rolled, controlled rolled or heat treated condition. After negotiation between the supplier and the demander and indicated in the contract, hot rolling and pickling can be carried out. Cold rolled GB 6653 gas cylinder steel plates and strips are delivered in annealed condition.
S235JR carbon steel plate is a kind of hot-rolled non-alloy structural steel under European standard EN 10025-2. The S235JR carbon steel plate has good plasticity, toughness, weldability and cold bending. Please refer to the following table for specific parameters: EN 10025-2 S235JR carbon steel plate has been widely used in the structural industry and is also a necessity in the construction industry. BBN steel sells S235JR carbon steel plate up to 500,000 tons every year, so BBN steel has quite rich experience in the production, processing and export of this kind of steel. If you need S235JR carbon steel plate, please contact us for advice.
ASME SA283 / SA283M - 03 is a specification for low and intermediate tensile strength carbon steel plates of structural quality for general applications. It cover four grades, A, B C and D, which have specified minimum yield strengths of 24, 27, 30 and 33 ksi, respectively. BBN STEEL can supply SA283 Grade B steel plates, SA 283 Gr B hot rolled sheets, SA283 Gr.B steel H beams and SA283Gr.B steel angles with high quality. ASME SA283 Grade B ms mild steel plate specification Thickness: 1.2-600mm Width:1220-4200mm Length: 5000-18000mm Notes: coil thickness â?¤ 25mm Shapes: plates, heavy plates cutting, sheets, steel angle, H beams, steel channels and I beams Manufacturing types: hot rolled
ASTM A516 Grade 70 (A516 Grade 485, A516Gr70) material is a carbon steel plate for moderate and low temperature service. The maximum thickness of plates is limited size 205mm/8inch, only by the capacity of the composition to meet the specified mechanical property requirements. A516 Grade 70 steel offers amazing weld-ability and amazing toughness, which is perfect for services at moderate and lower temperature ranges. We can supply A516 Grade 70 steel plates and A516 Grade 70 sheet stock with competitive price. A516 Grade 70 steel equivalent: EN 10028 P355GH A516 Grade 70 boiler steel plate size Thickness: 3-250mm Width: 1220-4200mm Length: 3000-18000mm Notes: coil thickness â?¤ 25mm Why Choose BBN Steel? 1. Competitive price and quality from our own factory 2. Approved by ISO9001, CE, SGS every year 3. Best online service with 24 hours reply 4. Deep processing service: cutting, welding, drilling, grinding, turning 5. Smooth production ability (3000tons/month)
A387 Grade 12 Class 2 steel can be used in high temperature environment of industrial boiler and pressure vessel manufacturing industry, the steel contains more molybdenum chromium element, which makes the ASTM A387 Grade 12 Class 2 has slight corrosion resistance, although compared with stainless steel, corrosion resistance seem a bit small, but compared with other types of steel is more durable, economical and practical. This is one of the reasons why ASTM A387 Grade 12 Class 2 steel is so popular. A387 Grade 12 Class 2 pressure vessel plate specification: Shapes: plates, sheet, steel strips, angle, channel and round bar Thickness : 1.5-200mm Width: 1220-4200mm Length : 5000-18000mm Notes: coil thickness â?¤ 25mm Why Choose BBN Steel? 1. Competitive price and quality from our own factory 2. Approved by ISO9001, CE, SGS every year 3. Best online service with 24 hours reply 4. Deep processing service: cutting, welding, drilling, grinding, turning 5. Smooth production ability (3000tons/month)
JIS G3125 SPA-C steel plate is one of the most popular products in the product category of weathering steel of BBN steel. Spa-c sheet has excellent resistance to atmospheric corrosion. It is widely used in air preheater, energy saving devices, railway cars, container production, bridge construction, construction and so on. SPA-C low alloy� steel specification: Shapes: plates, sheet, steel strips, angle, channel and round bar Thickness : 1.5-150mm Width: 1220-4200mm Length : 5000-18000mm Notes: coil thickness â?¤ 25mm Why Choose BBN Steel? 1. Competitive price and quality from our own factory 2. Approved by ISO9001, CE, SGS every year 3. Best online service with 24 hours reply 4. Deep processing service: cutting, welding, drilling, grinding, turning 5. Smooth production ability (3000tons/month)
A573 Grade 70 Carbon Steel Plate Latest price: 625 USD/ton ASTM A573 covers structural quality carbon-manganese-silicon steel A573 Grade 58, A573 Grade 65 and A573 Grade 70 plates in three tensile strength ranges intended primarily for service at atmospheric temperatures where improved notch toughness is important. Product name : ASTM A573 Carbon steel, A573 steel plate, A573 Structural steel plate, ASTM A573 Welding structural steel plates Dimension range : 1.2mm -680mm x 1000mm-4000mm x 1000mm-18000mm MOQ: 1 PC Product type : Steel plate Delivery time : Promptly ( Stock) or 10-40 days (Production) Stock : Available MTC: Available Payment Term : T/T or L/C At sight BBN Steel is a professional supplier of steel plate and steel section products in China. Welcome to contact us if you are interested in EN A573 Grade 70 steel price.
ASTM A588 Grade B(A588 Gr B) is a high-strength low-alloy structural (HSLA) steel in various shapes: plates, sheets, round bars and steel sections. This plate has a specified minimum yield strengths of 50ksi [345MPa] when plate thickness under 100mm. As a leading supplier of HSLA steel plate and sheet in China, we can supply A588 Gr B HSLA steel plate specification with various shapes and thickness up to 200mm[8 inch]. Mechanical properties Tensile strength min. MPa 485 Yield strength min. MPa 345 Elongation min. 21 ASTM A588 Gr B HSLA plate sheet specification Dimension range : 1.2mm -680mm x 1000mm-4000mm x 1000mm-18000mm MOQ: 1 PC Product type : Steel plate Delivery time : Promptly ( Stock) or 10-40 days (Production) Stock : Available MTC: Available Payment Term : T/T or L/C At sight For application, ASTM A588 Gr B HSLA plate and sheet in most environments are substantially better than that of ordinary carbon structural steels. When properly exposed to the atmosphere, this steel can be used unpainted for many applications.
SCFM C-shaped Steel Bracket C-shaped Steel is processed by the C-style automatic Molding Machine,the processing step is as belows, Discharging-Levelling--Molding--Shaping--Straighten--Measuring--Punching Hole--Punching Elliptical Coneection Hole---Cutting C-shaped Steel is mainly used for industrial workshop, civil construction, municipal engineering, oil platform, Bridges,'s girders, electrified railway electricity bracket, along the railway bridge steel structures such as light, super light h-beam very suitable for container, mobile houses, all kinds of garage, box train, electrical stents, various venues, small villas manufacturing. Size 80x40x2mm to 380x110x4mm Length 6m or as clients' request Material Q195,Q235,Q345,SS400, ect. Standard Chinese standard,ASTM,EN,JIS etc.
Specializing in the product Hot rolled steel coil steel sheet steel plate Company introduction Business Type: Trading Company Main Products: ERW Steel Pipe,Square Pipe,Steel Sheet,Steel Coil,Steel Strip Location: Tianjin, China (Mainland) Year Established: 2008 Year start exporting: 2002 Number Of Employees: 51 - 100 People Total Annual Sales Volume: US$10 Million - US$50 Million Main Markets: Western Europe, North America, Africa, Southeast Asia, Eastern Europe Average Lead Time: 30 Day(s) Product Description 1.Thickness:1.5-15mm 2.Width:600-2000mm 3.Standard:AISI,ASTM,BS,DIN,GB,JIS 4.Material:Q195,Q235B,SS400,ASTM A36,SPHC,etc. product name Hot rolled steel coil sheet plate thickness 1.5mm-15mm width 600mm-2000mm762mm,914mm,1000mm,1200mm,1219mm,1250mm application Transport, construction, shipbuilding, gas containers, etc standard AISI,ASTM,BS,DIN,GB,JIS material Q195,Q235B,SS400,ASTM A36,SPHC,etc. supplier HBIS, AnSteel(Sochi Olympic Supplier), BaoSteel,etc surface treatment chromated and oiled, chromated and non-oiled packing export standard package. payment T/T, L/C or DP min order 10tons or 25 tons (one 20ft FCL) coil weight 3-8ton or as client requirement
