Product Introduction Copper plating additive for copper plating machine it is used in rotogravure cylinder making copper plating machine. Product Advantage 1.Made of Japanese technology 2.Used for rotogravure copper plating machine 3.More fast plating speed 4.More durable,even plating surface 5.25kg per plastic barrels
Track gauge regulator Gauge adjuster is a new type of hydraulic tool suitable for rerouting rails on 50kg/m and 60kg/m rail lines and adjusting the position of concrete sleepers during line maintenance or laying new lines The gauge adjuster is a multifunctional combined railway maintenance and expansion tool. The gauge adjuster is mainly used for line diversion operations; it is suitable for gauge adjustment at forks and forks. Gauge adjuster parameters: thrust 15KN, stroke 30mm
Rail Gap Gauge Rail Gap Gauge is used for measuring the distance between two adjoining rails Benefits: Joint Gap Measuring Device shape: similar to carrot, tapered. This product is made of stainless steel , long service life. Easy to operate and easy to carry. Specification Model NW-BB Type Gap Gauge Material Stainless Steel Dimensions (L x W x H) (mm) 35*15*5cm Measure range 5-30mm Material Stainless steel MOQ 50 Pieces
Product Introduction Polishing Paste for rotogravure copper polishing machine is conjunction with Buffing cloth to copper surface of the gravure cylinder.No nick to the gravure cylinder Product Advantage Low cost and good quality
Crane rail pad MK2 Crane rail pad is located between a rail and the steel soleplate which improves the performance of crane rails.Cranes apply high forces to the structures on which they are mounted.The MK5 pad significantly reduces the stress between the rail and its support. The CRANE pad is one of the three key ingredients in achieving a reliable track. Rail pad should be narrower than the rail it is supporting (nominally 5mm). The pad is normally supplied in 12 meter lengths. The flutes of the pad are placed facing upwards. The pad may be cut to precise length of rail. It can be cut with a hacksaw or jigsaw. No installed length of pad should be less than the spacing between three pairs of crane rail fixing clips. Before installing Mark 2 pad, the supporting area should be clean and free of oil, grease or any projections likely to damage the pad. It is preferable that the steel structure below the pad is not painted. If the rail is to be welded the pad should be protected from excessive heat during welding by being removed under the weld or by being protected with a thermal barrier. Our technical department will be pleased to advise on the suitability of Mark 2 pad in specific installation conditions.
Product Description Rail turner Rail turn bar Turnover device consists of: cast rail turner head, high-quality carbon structural steel rod tip and seamless steel pipe welded together, utility model turn rail device, turning rail rail with a manual clamp tool. Easy to use, labor-saving, high efficiency, low labor intensity, easy to carry the railway staff, the railway sector is a dedicated tool for standing.
Snow wheels, winter wheel, supply for snow season, for North American market, Canada market. 12 inch to 20 inch.
Snow wheels, winter wheel, supply for snow season, for North American market, Canada market. 12 inch to 20 inch.
Bismuth is a silvery white to pink metal,which are mainly used to prepare compound semiconductor materials, high-purity bismuth compounds, thermoelectric refrigeration materials, solders and liquid cooling carriers in nuclear reactors, ect. Bismuth occurs in nature as a free metal and mineral. Product Name : Bismuth Ingot CAS NO 7440-69-9 Shape Ingot EINECS NO 231-177-4 Grade 4N Material Bismuth Appearance Silver-white color,with metallic luster,rectangular or trapezoidal rectangular 1. It is mainly used to prepare compound semiconductor materials, thermoelectric refrigeration materials, solders and liquid cooling carriers in nuclear reactors. 2.Used for preparing semiconductor high-purity materials and high-purity bismuth compounds. Used as a coolant in atomic reactors. 3. It is mainly used in medicine, low melting point alloy, fuse, glass and ceramics, and is also a catalyst for rubber production.
1. Product: PET Flakes 2. Grade: recycled Bottle Flake, Hot Washed 3. Color: 100% Clear, white 4. Form: Flake 6-14mm Product name: PET flakes, PET recycled flakes, PET resin, PET Grade:Recycled flakes, hot washed by Steam 80-90degree Color:100% clear, white, Blue/Green Transparency:90% PVC content:< 2ppm Moisture:< 1% Impurities:< 0.01% Packing :25 / 50 / 100 / 500 / 1000kg per bag Packing material:PP woven bag or paper bag Loading weight:25.00 TON per 40HQ Supply ability:1000 per month Minimum order quantity:25 TONS
Magnesium ingot Features: 1.Corrosion resistance and light weight. 2.The density of magnesium is 1.74g/cm3 which is even lighter than aluminum 2.7g/cm3, but mechanical strength and chemical stability are much better than aluminum. 3.Magnesium can be directly related to nitrogen, sulfur and halogen such as chemical combination, including hydrocarbons, aldehydes, alcohols, phenols, amines, grease and most of the oil pharmaceutical . Chemical composition : Mg Ingot Brand Chemical composition Mg Fe Si Ni Cu Al Cl Mn others Mg99.98 99.98 0.002 0.003 0.002 0.0005 0.004 -- 0.002 0.02 Mg99.96 99.96 0.004 0.004 0.0002 0.002 0.006 0.003 0.003 0.04 Mg99.95 99.95 0.004 0.005 0.0007 0.003 0.006 0.003 0.01 0.05 Mg99.9 99.9 0.04 0.01 0.001 0.004 0.02 0.005 0.03 0.1 Mg99.8 99.8 0.05 0.03 0.002 0.02 0.05 0.005 0.06 0.2 Application : 1.Magnesium alloys can be used to manufacture aircraft fuselages,engine parts, etc. 2.As strong reducing agent for titanium, zirconium, beryllium, uranium and hafnium production. 3. Magnesium metal is the main alloying element in aluminum alloy 4.Magnesium powder can be used as desulfurizer for steel making. 5. Magnesium also used to make photography and optical instruments, etc. 6.Can be used to produce magnesium fertilizer, promote the absorption and utilization of phosphorus by plants. 7.As an additive agent in conventional propellants and the production of nodular graphite in cast iron.
High Quality CAS 12190-79-3 Cobalt Oxide for Lithium Battery Cathode Material Lithium cobalt oxide, also known as lithium cobalt oxide, chemical formula LiCoO2, is an inorganic compound that is generally used as a positive electrode material for lithium-ion batteries. The structure of LiCoO2 has been studied by X-ray diffraction, electron microscopy and neutron powder diffraction. The lithium atomic layer lies between plates of regular octahedrons formed by cobalt and oxygen atoms (shown below). This structure is in agreement with the structure predicted by the theory. Lithium cobalt oxide is toxic and should be handled safely. Items Standard Result Co 60.0�±1.0 59.56% Li 7.0�±1.0 7.18% Na 300max 220ppm Fe 200max 29.0ppm Ni 300max 3.0ppm Ca 300max 22.0ppm Cu 200max 4.0ppm Moisture 500max 156ppm PH 11.2max 10.62 200mesh 100% pass 100% pass Tap Density 2.7min 2.8g/cm3 SSA 0.10-0.30 0.16m2/g D10 3.0min 5.6�¼m D50 8~12 9.9�¼m D100 60.0max 29.0�¼m First Discharge Capacity 158.0min 159.0mAh/g 1. The electrochemical performance is superior a. The average cycle capacity attenuation per cycle 135mAh/g c. 3.6 V first discharge platform rate > 85% 2. The processing performance 3. Tap density is big, help to improve volume specific storage battery 4. Product performance is stable, good consistency
Polyamide PA66 has good rigidity, hardness, abrasion resistance and thermal dimensional stability. In addition, PA66 has outstanding wear resistance and low frictional properties. It also has very good temperature, chemical, and impact properties. Users should be aware of PA66 propensity to absorb moisture which could affect dimensional stability. In fact, PA66 will tend to absorb more moisture at saturation than cast PA6G. The material is used in: Automobile industry Engineering industry Production of single-purpose machines
Our HDPE reprocess resin or granule is customized developed by our own factory, hasing multiple color and specification, the color include blue, transparent, white, variegated, milky white, yellow, blue, black and red. it is High Density Polyethylene hdpe recycled granule dana pellet for film or bottle made in China hdpe granule. HDPE Drum Recycled Blow/Blowing Grade HDPE for HDPE Blue Drum Applied Areas Direct Process Impact Strength >6 KJ/m2 Appearance Granule Density >0.85g Tensile Strength >20MPa Elongation at break >250% Melt Flow Index 0.36-3 Size Customized Ash Content
Applied Areas Direct Process Impact Strength >20 KJ/m2 Appearance Granule Density >0.85g Tensile Strength >20MPa Elongation at break >250% Melt Flow Index >8 Size Customized Ash Content
Hot washed HDPE blue drum scraps 1. Formula: [CH2CH2]n 2. CAS: 9002-88-4 3. Grade: Recycled injection grade 4. Shape: Granules/pellets/Flakes Application 1.HDPE recycled material for drums, the product will be with excellent properties such as easy extrusion, impact resistance and cryogenic resistance after plastic modification, can be directly processed and produced, and commonly used in municipal pipes, water supply pipes, jacking pipes, carat pipes, inner rib pipes, steel belt winding pipes, bellows, pipe fittings, wood plastics, blow molding (cardboards, bottles and barrels), blow membrane and others. 2.Recycled plastics are obtained by recycling, crushing, cleaning, and processing waste plastics, and then the recycled plastics are modified to produce sanitation bucket particles with excellent normal temperature and cryogenic toughness, which can be directly injection-molded to produce sanitation buckets.
Tin ingot 99.9%: 1. High quality and professional service 2. Tin ingot 99.9%, 99.95%, 3. Best price Tin ingot 99.9%: 1. Tin ingot is widely used as a coating material in High-precision electronic products, and other requirements of precision welding products, welding products, general electronics, food industry packaging, automotive and electrical industry, and high temperature resistant products. Item Sn 99.90 Sn 99.95 Sn 99.99 Sn % 99.9 99.95 99.99 As % 0.008 0.003 0.0005 Fe % 0.007 0.004 0.002 Cu % 0.008 0.004 0.0005 Pb % 0.032 0.02 0.0035 Bi % 0.015 0.006 0.0025 Sb % 0.02 0.014 0.0015 Cd % 0.0008 0.0005 0.0003 Zn %â 0.001 0.0008 0.0003 Al % 0.001 0.0008 0.0005 S % 0.0005 0.0005 0.0003 Ag % 0.005 0.0001 0.0001 Ni+Co % 0.005 0.005 0.0006
Product Item:Fully Refined Paraffin Wax 64/66 Test Date:2020-03-03 Test Item Quality Index The Measured Quality 52-58 60-70 Melting Point (�ºC) 64~66 59.1 Oil Content % Max 0.5 0.34 Color Saybolt # Min+27 Min+25 30 Light Stability # Max 4 Max 4 4 Needle Penetration(25�ºC) 1/10mm Max 19 Max 17 18 KinematicViscosity(100�ºC) mm�²/s REPORT 4.107 Odor # Max 1 1 Conclusion Qualified fully refined paraffin The fully refined paraffin wax has a white solid appearance with block or granular structures. It has high melting point and low oil contains. It also has features of no bonding, no sweating, no greasy feeling, waterproof, moisture-proof and electrical insulation under normal temperature. Due to the depth of refinement, the products are of low content of polycyclic aromatic hydrocarbons, good chemical stability and light stability, strong toughness, good plasticity, white color, no mechanical impurities and water, and no smell. Fully refined paraffin can be dissolved in: benzene, ether, chloroform, carbon disulfide, carbon tetrachloride, turpentine, petroleum, and fixed oil.
Silicon Ore is an ore that drops Raw Silicon which can be used in the Circuit Fabricator to craft Basic Wafers, Advanced Wafers, or Blue Solar Wafers. It can be destroyed using any type of pickaxe, but it will only drop Raw Silicon if you use an Iron Pickaxe, Heavy Duty Pickaxe, Diamond Pickaxe, or Desh Pickaxe.
Product Description Food grade liquid silicone is used to .candy, cake and cholocate and soap mold and making artificial stone,cement and gypsum. Food grade quality silicone with nontoxic,Excellent fluidity, high tear and tensile strength, High duplication times repeated use, easy to demould,High temperature resistance and cure can be accelerated by heat Model 6210 6215 6220 6225 6230 Mixing ratio (A:B) 1:1 1:1 1:1 1:1 1:1 Hardness (Shore A)â?¥ 10 15 20 25 30 Tear-strength (kgf/c m�²)â?¥ 16 18 20 21 22 Viscosity (A/B mixed 25�°C mpa.S) 8000�±2000 8000�±2000 10000�±2000 10000�±2000 10000�±2000 Shrinkagerate (%)â?¤ 0.1 0.1 0.2 0.1 0.1 Elongation(%) 500 480 450 450 400 How to use: 1.A and B must be mixed evenly into a clean plastic or metal container, The bottom and walls of the container must be scraped well to ensure that the silicone is mixed with the curing agent. 2.The pre-operation time of the mixed is 30-40 minutes at room temperature, and the product prototype is poured by vacuum defrosting.The product can be cured completely at room temperature of 3-4 hours and heated at 80-120�ºC for 30 minutes. 3. When pouring or brushing mold for medium or large products, it is recommended to pour or brush 2-3mm thick silica gel on the surface of the product to fully and completely contact with the prototype. Package: 10KG, 20KG, 200KG or according to customer requirements.
