150T-200T Aluminium Sheet Rolling Mill Material: Aluminium Scrap Finished product: Aluminum sheet width 200mm-940mm, Thick 0.6 ~ 1.6mm, Output: 150-200 tons per month , Medium frequency furnace (1 ton) , The main machine: 400 X 1300 two rollers reversible rolling mill , Screwdown mode: single stage screwdown drive, manual clutch , Screwdown motor: Y 6 N =4.5 KW, 2 units, with screwdown, lifting at the same time .Also can be respectively screwdown, lifting. Center distance of screwdown worm gear box: A=270mm, Screw-down adiusting screw S150 X 10, material: 40 Cr, Screw-down display: screwdown the indicator. Mechanical alignment guide device before the machine and after the machine Motor 3KW} JZQ250 reducer, Roll size: 400 X 1300, Roller specifications 120 X 1300, pitch: 170 H-shaped rolls , The electric control cabinet to motor operation box to the cable, electrical wires between the control line and installation accessories by The buyer is responsible for themselves. The equipment lubrication station, the supplier provides pipeline layout, the connecting pipeline under the machine, The equipment covers an area of 30m X 15m , The above technical parameters for aluminum sheet Rolling.
150T-200T Aluminium Sheet Rolling Mill Material: Aluminium Scrap Finished product: Aluminum sheet width 200mm-940mm, Thick 0.6 ~ 1.6mm, Output: 150-200 tons per month , Medium frequency furnace (1 ton) , The main machine: 400 X 1300 two rollers reversible rolling mill , Screwdown mode: single stage screwdown drive, manual clutch , Screwdown motor: Y 6 N =4.5 KW, 2 units, with screwdown, lifting at the same time .Also can be respectively screwdown, lifting. Center distance of screwdown worm gear box: A=270mm, Screw-down adiusting screw S150 X 10, material: 40 Cr, Screw-down display: screwdown the indicator. Mechanical alignment guide device before the machine and after the machine Motor 3KW} JZQ250 reducer, Roll size: 400 X 1300, Roller specifications 120 X 1300, pitch: 170 H-shaped rolls , The electric control cabinet to motor operation box to the cable, electrical wires between the control line and installation accessories by The buyer is responsible for themselves. The equipment lubrication station, the supplier provides pipeline layout, the connecting pipeline under the machine, The equipment covers an area of 30m X 15m , The above technical parameters for aluminum sheet Rolling.
Stainless steel bar/copper tube straightener machine-dalian chengjin special steel products co., ltd. Was established in 2006, was a specialized enterprise integrating r&d, production and marketing of round steel bars, tubescenterless lathe (steel peeling machine, burnishing machine) two roll of high-precision straightening calender. My company production of peeling machine processing raw material diameter from �10� to 250mm, straightening calender processing raw material diameter from �10mm to �160mm. We also provide custom-designed equipments for different customer demands., our equipment useing the latest technologymeeting the international mainstream machining requirements, and having characteristics of low energy consumption, high efficiency and reasonable price., over the years, our round steel peeling machine, straightening machine and other products have sold to more than 50 domestic and foreign companies like :shanghai, chongqing, sichuan, jiangsu, hubei, anhui, zhejiang, liaoning, etc. Since 2013our machines have been exported to russia, japan, india, and taiwan ect., our clients give a good evaluation and trust and purchase our equipment many times., main productswire bar centerless machine china, wire bar peeling machine china, steel bar straightening machine china, wire rod burnishing machine china, two-rolls straightening machine china.
Work Principle SLAB CUTTER The power is transmitted to the movable blades on the main shaft through the reducer with torque increased. The movable blades and the fixed blades break up the nature rubber, synthetic rubber and other rubber block into smaller pieces as it required for the preparation of the next process. A spray system is available in this machine. It breaks the rubber blocks and cleans the it at the same time. Function SLAB CUTTER It is a high-efficient breaking machine which is the key equipment and the first machine for crumb rubber (rubber block) process.It breaks rubber block into small size, which is convenient to the next stage dehydration process.
China manufacturer of two-roll straightening machine -china dalian chengjin special steel products co., ltd. Established in 2006, was a specialized company engaged in the production of steel bar peeling machine, centerless machine, steel bar straightening machine. Main products:wire bar centerless machine china, wire bar peeling machine china, steel bar straightening machine china, wire rod burnishing machine china, two-rolls straightening machine china, etc. Now our company has centerless lathe models of bp-80, bp-40, bp-150, wc-250, and high-precision straightening calender models of jp-15, jp-50, jp-80, jp-150. Our products are basis of foreign models on the proven innovation improved. Its quality, technology and the results are world class. Our clients give a good evaluation and trust.
Steel bar rust removal machine china manufacturer-Dalian Chengjin Special Steel Products Co.,Ltd. was established in 2006, was a specialized enterprise integrating R&D, production and marketing of Round steel �Bars, Tubes�Centerless lathe (Steel peeling machine, Burnishing machine) �Two roll of high-precision straightening calender. My company production of Peeling machine processing raw material diameter from Φ10Φ to 250mm, Straightening calender processing raw material diameter from Φ10mm to Φ160mm. we also provide custom-designed equipments for different customer demands. Our equipment useing the latest technology�meeting the international mainstream machining requirements ,and having characteristics of low energy consumption, high efficiency and reasonable price. Over the years, our round steel peeling machine, straightening machine and other products have sold to more than 50 domestic and foreign companies like :Shanghai, Chongqing, Sichuan, Jiangsu, Hubei, Anhui, Zhejiang, Liaoning, etc. Since 2013�Our machines have been exported to Russia, Japan, India, and Taiwan ect.,Our clients give a good evaluation and trust and purchase our equipment many times. Main products�Wire Bar Centerless Machine China, Wire Bar Peeling Machine China, steel bar straightening machine China, wire rod burnishing machine China, two-rolls straightening machine China, etc.
Stainless steel bar polishing machine-Dalian Chengjin Special Steel Products Co.,Ltd. was established in 2006, was a specialized enterprise integrating R&D, production and marketing of Round steel Bars, TubesCenterless lathe (Steel peeling machine, Burnishing machine) Two roll of high-precision straightening calender. My company production of Peeling machine processing raw material diameter from Φ10Φ to 250mm, Straightening calender processing raw material diameter from Φ10mm to Φ160mm. we also provide custom-designed equipments for different customer demands. Our equipment useing the latest technologymeeting the international mainstream machining requirements ,and having characteristics of low energy consumption, high efficiency and reasonable price. Over the years, our round steel peeling machine, straightening machine and other products have sold to more than 50 domestic and foreign companies like :Shanghai, Chongqing, Sichuan, Jiangsu, Hubei, Anhui, Zhejiang, Liaoning, etc. Since 2013Our machines have been exported to Russia, Japan, India, and Taiwan ect.,Our clients give a good evaluation and trust and purchase our equipment many times. Main productsWire Bar Centerless Machine China, Wire Bar Peeling Machine China, steel bar straightening machine China, wire rod burnishing machine China, two-rolls straightening machine China, etc.
Stainless steel bar/copper tube straightener machine-dalian chengjin special steel products co., ltd. Was established in 2006, was a specialized enterprise integrating r&d, production and marketing of round steel bars, tubescenterless lathe (steel peeling machine, burnishing machine) two roll of high-precision straightening calender. My company production of peeling machine processing raw material diameter from �10� to 250mm, straightening calender processing raw material diameter from �10mm to �160mm. We also provide custom-designed equipments for different customer demands., our equipment useing the latest technologymeeting the international mainstream machining requirements, and having characteristics of low energy consumption, high efficiency and reasonable price., over the years, our round steel peeling machine, straightening machine and other products have sold to more than 50 domestic and foreign companies like :shanghai, chongqing, sichuan, jiangsu, hubei, anhui, zhejiang, liaoning, etc. Since 2013our machines have been exported to russia, japan, india, and taiwan ect., our clients give a good evaluation and trust and purchase our equipment many times., main productswire bar centerless machine china, wire bar peeling machine china, steel bar straightening machine china, wire rod burnishing machine china, two-rolls straightening machine china.
The mill is used to manufacture of round pipe from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths. 1.The High precision tube mill has some advantages as follow: between level roller jumps 0.01,between frame and slide clearance â?¤0.02mm, frame vertical degree â?¤0.05, each frame parallel degree â?¤0.1mm steel pipe diameter and roundness errorâ?¤0.08mm. 2.Product Process: material(steel coil)â??uncoilerâ??shear and welderâ??horizontal(or cage) accumulatorâ??forming millâ??HF soild welderâ??sizing millâ??rounghly straightening(turkey head)â??cut off machineâ??run out table 3.The Basic Parameters: stands of forming mill 7 stands of sizing mill 5 shaft material 40Cr round pipe diameter 19-76mm Round pipe thickness 1.5-3.0mm square pipe size 15Ã?15-60Ã?60mm square pipe thickness 1.5-2.0mm we can design the machine according to the customer detail require.
Main Features (1) Can recover R22, R134A,R407C, R404A, R410A, etc; (2) Oil-free compressor design, can directly recover gaseous, liquid or gas-liquid mixture of refrigerant; (3) Automatic high pressure cut-off switch for Safety; large fan and efficient condenser design, recycling, filling faster; (4) Can be recovered to negative pressure, recycling more thoroughly; (5) Multi-function valve design, you can automatically remove the residual refrigerant inside the machine to prevent refrigerant cross-contamination; (6) Large filter external design, can effectively remove the refrigerant after recovery of moisture and impurities; (7) Complete high-voltage protection, current protection, for the operation of the system provides a security; (8) Humanized bar design, easy to carry out; (9) Shell with a one-time rotation molding technology, high strength, impact resistance, practical and strong; (10) High-power motor design, can work 24 hours a day.
The Fifth Generation SKM-B Series Peel-Off End Manufacturing Machine The series machine was successfully developed in 2017, and formally put into use by customersï¼?can be used to manufacture POE,and specially suitable for bigger 202-701# iron POE. It can automatically complete the functions of lids feeding, punching, deep drawing, crimping, aluminum foil pre-sealing, sealing, embossing and output etc. Independent servo controls each function module, adjusts parameters separately, and achieves high speed response and synchronous movement. Inclined punching arrangement makes the aluminum foil waste least. We can make any new model according to clientsâ?? requirement. All the information for reference onlyï¼?The products are subject to change without notice. The various types of equipment we provide are customized according to the needs of customers, and the price will be discussed after the meeting.
The Fifth Generation SKM-B Series Peel-Off End Manufacturing Machine The series machine was successfully developed in 2017, and formally put into use by customersï¼?can be used to manufacture POE,and specially suitable for bigger 202-701# iron POE. It can automatically complete the functions of lids feeding, punching, deep drawing, crimping, aluminum foil pre-sealing, sealing, embossing and output etc. Independent servo controls each function module, adjusts parameters separately, and achieves high speed response and synchronous movement. Inclined punching arrangement makes the aluminum foil waste least. We can make any new model according to clientsâ?? requirement. All the information for reference onlyï¼?The products are subject to change without notice. The various types of equipment we provide are customized according to the needs of customers, and the price will be discussed after the meeting.
Condition:New Laser Type:Fiber Laser Cooling Mode:Air Cooling Control Software:EZCAD Software Graphic Format Supported:AI, DXF, laser marking machine Working Accuracy:0.01mm Place of Origin:Shandong, China (Mainland) Brand Name:Hanten laser Model Number:HTF-20/30/50/100T Power(W):20W/30W/50W/100W Certification:CCC, CE, SGS After-sales Service Provided:Engineers available to service machinery overseas Laser source:Raycus IPG JPT,CAS ,Max Marking Depth:0.01-5mm (according to different material ) laser wavelength:1064nm Marking speed:
HENAN KOWLOON MACHINERY CO., LTD. The company has 20 years history of be engaged in steel bar cutting, steel bar bending and other construction machinery industry,the quality and quantity are in the lead numbers of China.and the productions has been exported to Southeast Asia, Russia, the Middle East, Africa and South America countries and area. We hope to have a pleasant cooperation with you.
This kind of high power metal laser engraving machine specially fit for processing high reflective material such as brass ,red copper and galvanize sheet etc . Features: a.The high power fiber metal laser engraving machine with better laser beam quality , lower operating costs , less power consumption and loger working life by using the new generation IPG fiber laser source. b. The Metal laser engraving machine equipped with PRECITEC new generation pro-cutter laser cutting head , optimized cutting process , monitoring cutting condition through APP use easily and friendly c. Eagle eye(CCD) technology , ultra0fast positioning the sheet metal edge , minimum cutting down time , In addition , it also can process punching parts and precut parts ,due to secondary positioning function d. Optimized cutting technology with programmable laser frequency and focus position , to achieve high efficiency processing on different thickness& type sheet metal . ll cutting parameters can be programmed , no need human intervention e. Automatic energy saving mode: while stop over 5 minutes , machine automatically switch into standby mode , to reduce power consumption . f. Auto exchanging table with Hydraulic lifting system; ensure synchronous running for metal laser engraving machine , reliable and stable g. The metal laser engraving machine with remote function , can remotely monitor the running conditions of machine , much easier for service and faster response h. With ergonomic design , equipped with intelligent operation terminal , user-friendly and easy to learn Applicable materials Metal materials such as aluminum alloy , Galvanize sheet , Carbon steel , stainless steel , Brass , Red copper etc. Technical Parameter Maximum material size 4000X2000 mm Laser power 4000W/6000W/8000W/10000W Maximum speed 170m/min Positioning Accuracy ±0.05mm(VDI/DGQ3441) Repeated accuracy ±0.03mm(VDI/DGQ3441) Model MACH2040/6025 Work environment Temperature 0-45 Humility 80%clean, less dust Maximum accelerated speed 2.2(G) Total Power 18kw/25kw Machine weight 13.5T/15.5T Dimension Mach4020: 12000*3500*2200mm Mach6020: 15500*4200*2200mm
Paint Bucket Crusher / Industrial Aluminum Can Crusher Civilian scrap metal has high recycling ratio in recycling system, most of that is small and light scrap by different quality with feature of rusted easily, low molten steel like waste household appliances shells, metal furniture , metal door and window, bicycle, color steel tiles, car shells Etc. It should get great tredted like de-dusting , rusty-removing, increasebulk density if you want get preferable recycling.
Materials available:stainless steel, carbon steel, brass, bronze, iron, alumunum alloy, etc Processing method:cnc machining, turning, milling, drilling, stamping, punching, sheet metal, grinding, die casting, welding, assembly Surface treatment:anodizing, electroplating, polishing, powder coating, blacken, hardening, paining, ect.
Materials available:stainless steel, carbon steel, brass, bronze, iron, alumunum alloy, etc. Processing method:cnc machining, turning, milling, drilling, stamping, punching, sheet metal, grinding, die casting, welding, assembly. Surface treatment:anodizing, electroplating, polishing, powder coating, blacken, hardening, paining, ect.
Metal Shredder is a mechanical equipment used for metal scrap recycling. It can crush, compress and shear various metal scraps such as scrap aluminium, scrap iron, scrap steel, etc. to facilitate subsequent separation, purification and reuse. Metal Shredder plays an important role in the field of metal recycling through efficient and environmentally friendly metal scrap processing.
Industrial 4*8 table CNC plasma cutter (CNC plasma cutting table) is one kind of multi-functional metal CNC cutting machine. It is suitable for cutting and drilling steel plates, and can also be used for cutting circular tubes. Industrial 4*8 table CNC plasma cutter (CNC plasma cutting table) features: 1. This CNC plasma cutter (CNC plasma cutting table) combines cutting and drilling to reduce process steps. Raw metal material becomes finished part by proceeding in one time. The efficiency and precision are increased significantly. And the cost of delivery, power and human resource is reduced. 2.Indine design under table surface makes finished parts and scrap slide down to both side along, convenient and safe for operator. 3.Professional control system with auto metal saving function. English, Russian, Spanish, French, Japanese, Czech, Slovak operation interface, supporting file reading from U disk or downloading from computer, providing high independence and great convenience during operation. 4.Racks and gears as transmission raise moving speed so that large area cutting can be done in short time. 5.Lower noises ,stable and accurate coordinate movement . 6.American Hypertherm plasma power , higher working strength ,long time use. option 45A,65A, 105A and so on 7. Steel structure lathe bed is capable of loading heavy metal sheet of large size. Working area according to client's need option. After-sale Service of Industrial CNC plasma cutter (CNC plasma cutting table): 1. Warranty 2 years 2. Engineers available to serve machine overseas 3. Strict factory inspection 4. Complete equipment manual 5. Online instruction 6. Provide all components, spare parts and consumptive material
