In scientific research institutions or pharmaceutical companies, some biological samples need to be stored in liquid nitrogen sample storage tanks. Liquid nitrogen sample storage tanks are an important cryogenic storage equipment that many people are not familiar with. So as a manufacturer of KGSQ liquid nitrogen tank, let me briefly introduce how to use it. 1. Before use, you need to carefully check the appearance to see if there is any dent or damage, and whether the vacuum exhaust port is intact. These inspections are to ensure that the thermal insulation performance of the liquid nitrogen tank is good. 2. Liquid nitrogen tanks rely on liquid nitrogen to ensure deep and low-temperature storage, so the tanks can only be filled with liquid nitrogen. Mixing other flammable substances can easily cause interaction and cause an explosion. 3. The liquid nitrogen tank container should be placed in a cool, dry place to ensure good indoor ventilation. 4. The temperature of liquid nitrogen is -196�°C. Self-protection measures should be taken when extracting and storing the freezing rack, such as wearing leather or cotton gloves. Be cautious when operating with bare hands. At the same time, it is necessary to prevent liquid nitrogen from splashing, which may cause frostbite when it touches the skin and other parts. 5. When filling liquid nitrogen for the first time, because the vacuum liner is at normal temperature, it is not advisable to fill it too fast. A small amount should be injected first to gradually reduce the temperature of the liner. Injecting a large amount of liquid nitrogen can easily cause the liquid nitrogen to boil. At this time, slow down. Wait for the liquid nitrogen to cool down slightly before injecting liquid nitrogen faster. Otherwise, the liquid nitrogen will boil and splash outward, causing frostbite. 6. Liquid nitrogen should not be overfilled, and the liquid level should not be in contact with the fiberglass neck tube. 7. Liquid level height check: Insert a wooden ruler vertically into the center bottom of the liquid nitrogen tank and take it out after about 15 seconds. The frost length is the liquid level height. Never use a hollow tube for inspection to prevent liquid nitrogen from erupting from the tube and injuring people. 8. Make sure that the liquid nitrogen submerges the refrigerated items. When the liquid nitrogen is consumed to the point where the refrigerated items are about to be exposed to the liquid surface, liquid nitrogen should be replenished in time. If you have any needs, please contact KGSQ liquid nitrogen tank:
As we all know, a soldier with a very handy weapon can exert greater combat effectiveness in battle. This sentence tells us that no matter what position you are in, a handy "weapon" can make you more handy in the work process and get twice the result with half the effort. In our scientific research institutes and laboratories, we cannot do without a handy "weapon", and this "weapon", in my opinion, is a laboratory liquid nitrogen tank. Why I say this is because in the laboratory, experimental samples are particularly important. They generally need to be stored at low temperature. Its safety directly affects the accuracy of experimental results. Laboratory liquid nitrogen tanks provide a safe and stable low-temperature storage environment for experimental samples. Of course, laboratory liquid nitrogen tanks do not only have this feature, they also have: 1. Large capacity storage space In scientific research institutes and laboratories, there will be a situation in which experimental samples are stored in large quantities and types, and most of them need to be stored for a long time. At this time, small-capacity jars are used, which not only has limited storage space and cannot be stored in categories, but also requires frequent refills. Therefore, the liquid nitrogen tanks usually used in laboratories are above 30 liters. 2. Large diameter + square bucket In order to facilitate the staff to find and manage samples, and because the number of samples is relatively large, laboratory liquid nitrogen tanks are usually used as formula buckets, which can store cell samples in separate compartments, in large and regular quantities, and can also be stored in categories. Due to the size limit of the square pail, laboratory liquid nitrogen tanks are all large-diameter, above 125mm, and the commonly used diameters are 125, 127, 210, and 216mm. 3.Safety lock cover Experimental samples are crucial to every worker doing experiments. Therefore, the safety of the samples cannot be ignored. In order to ensure the safety of the samples and prevent them from being accidentally taken or lost, in addition to square buckets and protective covers, usually A lock cover will be added and a lock will be installed to ensure safety. With so many features, the laboratory liquid nitrogen tank is not a useful "weapon" for the laboratory. If you have any needs, please contact KGSQ liquid nitrogen tank: Email: 1tcln2container@126.com WhatsApp: +86118903712477 Official website: https://www.cryogenicstoragetank.com/YDS-Series-with-Racks-Boxes.html
ZY-NS80-1X The multifunctional membrane separation system is a high-efficiency, low-energy consumption, normal-temperature physical separation system carefully developed and designed by "Zhuoyue Filtration" by introducing microfiltration membrane technology, ultrafiltration membrane technology, nanofiltration membrane technology, and reverse osmosis membrane technology (material-specific) , used for material filtration, separation, purification, concentration, decolorization, desalination and other process purposes, and is widely used in biology,food, chemical industry, environmental protection and other fields.
ZYTEST--DI Water Machine ZYTEST Deionized Water System for Hospital Test is usually used for rountine chemical laboratory analysis instruments especially biochemical analyzer. The equipement with simple and generous appearance can easily produce water grade II (0.1-1 us/cm ultra-pure water) and water grade III (2-10 us/cm pure water for glass ware washing) which meets standard ASTM, CAP, NCCLS, GB and T6682-2008.
Pipettes are indispensable tools in laboratories, research facilities, and medical settings, used to accurately measure and transfer liquids. To ensure consistent and reliable results, it's crucial to properly maintain and care for your pipettes. In this article, we'll provide essential tips for pipette maintenance to help prolong their lifespan and maintain accuracy. 1. Regular Cleaning Clean your pipettes regularly to prevent cross-contamination between samples. Use a mild detergent and distilled water to clean the external surfaces. For the internal components, use a lint-free cloth dampened with isopropanol or ethanol to wipe down the pipette shaft and piston. Make sure to follow the manufacturer's guidelines for cleaning to avoid damaging delicate components. 2. Calibrations and Verification Schedule regular calibrations and verifications of your pipettes to ensure accurate measurements. Calibration checks should be performed by trained professionals using calibrated equipment. Verification using gravimetric or photometric methods can help confirm the accuracy of your pipettes when dispensing specific volumes. 3. Proper Handling Handle pipettes with care to avoid mechanical damage. Always use the appropriate force when operating the plunger to prevent excessive wear on internal components. Avoid dropping pipettes or subjecting them to impact, as this can lead to misalignment and inaccurate measurements. 4. Tip Selection and Replacement Choose pipette tips that are compatible with your specific pipette model. Use high-quality, certified tips to ensure accurate and consistent results. Replace tips between each sample to prevent cross-contamination. Make sure the tips are securely attached to the pipette to prevent leakage or imprecise measurements. 5. Storage and Handling Store your pipettes in a clean and dry environment to prevent dust and contaminants from affecting their performance. Use pipette stands to keep them upright and avoid contact with surfaces. If your pipettes are not in use for an extended period, store them with the plunger released to relieve stress on internal components. Conclusion Proper maintenance of pipettes is essential for obtaining accurate and consistent results in laboratory and medical settings. By following these tips and adhering to manufacturer guidelines, you can ensure that your pipettes remain in optimal condition, extend their lifespan, and contribute to the reliability of your research and analyses.
Heavy weight double-sided reflectors are incredibly versatile and can be used in a wide variety of underground applications Constructed from microprism retroreflective vinyl with brass grommets, these reflectors are extremely bright and offer true color reflection. With 11 different color options available, they can be used to create a complete mine color code identification system. Both sides of the reflector can be the same color or different colors, and one side may also be non-reflective. The reflectors are flexible and impact resistant and have a smooth surface that can be easily wiped clean. They can be installed quickly using an S-hook or special roof plate clip.
Compatible with OpenTrons OT-2 exactly Stackable pipette tips Proof static electricity affordable, replaceable to orignal brand
Rainin tips, aerosol filter pipet tips for Rainin, LTS pipette tips, micro pipette tips, Rainin LTS tips,
4. Performance specifications 1. Temperature range: RT+40 -70 2. Humidity range: 90% RH 3. Temperature control accuracy: ± 3 *Note: The performance guarantee of item # 5 above requires testing at a distance of 1/6 of each wall surface in the testing area, and must be measured after stabilizing with temperature and humidity for 30 minutes 4. Equipment placement space: at least 207 two hundred and seven 201cm (W H D) 5. Power supply: AC220V 50HZ 5 System structure 1. Heating system: Scaled stainless steel electric heating tube 2. Humidification system: glass nozzle 3. Temperature sensing system: Made of stainless steel SUR304Pt100 4. Control system: The control system adopts a P.I.D controller, which controls temperature and humidity simultaneously a. Controller specification: Accuracy: Temperature ± 2.0 +1 digit, with upper and lower limit standby and alarm functions 5. Box material Inner box material: SUS # 304 mirror stainless steel plate Outer box material: SUS # 304 stainless steel plate
model Basic parameters DL-60 DL-90 DL-120 DL-160 DL-200 Dimensions inside the test chamber (Long �? wide �? High) 600*450*400mm 900*600*500mm 1200*1000*500mm 1600*1000* 500mm 2000*1200* 600mm Test chamber volume 108L 270L 600L 800L 1440L Volume of brine tank 15L 25L 40L 40L 40L Laboratory temperature NSS ACSS 35�±1â??ï¼?CASS 47�±1â?? Pressure barrel temperature: NSS ACSS 47�±1â??ï¼?CASS 63�±1â?? Brine temperature: 35â??�±1â?? Spray mode Ordinary type without suffix letter, economical type (M) continuous spray (A), programmable spray (B) Spray volume: 1.0ï½?2.0ml/80cm2/h(Different mist collectors need to be converted according to this ratio) Spray pressure 1.00+0.01kgf/cm2 source AC 220V 10A AC220V 10A AC220V 16A AC220V 16A AC220V 16A
2.Technical parameters: 1. Box size in the laboratory: DL-120LA W1200 * D1000 * H500 (mm), Approximate dimensions: 2300 * 1300 * 1400mm, 2 standard temperatures, Laboratory temperature: nss acss 35 ± 1 /pass 50 ± 1 Pressure bucket humidity: nss acss 47 ± 1 /pass 63 ± 1 , Salt water temperature: 35 ± 1 It can be heated without water, 3 volumes, Laboratory capacity: 800L Salt water tank capacity: 40L, 4 compressed air, Compressed air pressure: 1.00 ± 0.01kgf/c 5 spray volume: 1.0-2.0ml/80c /h, 6 spray mode: continuous spray, timed spray, programmable spray, intermittent spray, demisting in the box, 7. Power supply: AC220V 50Hz/20A, 8. Material: The entire PVC board is made, and the salt spray testing machine adopts advanced three-dimensional reinforcement technology internally, with a strong and solid structure that never deforms. 9. Water adding method: An automatic water adding system is adopted, which has the function of automatically replenishing the water level when the water level is insufficient, and the test is not interrupted. 10. Nozzle: Precision glass nozzle, salt spray testing machine used for 4000 hours to ensure no crystal blockage. 11. Protection system: Equipped with dual over temperature protection and insufficient water level warning to ensure safe use. 12. Temperature controller: digital display, PID control, high stability platinum temperature probe, error 0.3 13. Heating method: The laboratory adopts direct steam heating method, which increases the temperature quickly and shortens the standby time of the salt spray testing machine. 14. The spray tower is equipped with two conical dispersers, which have the functions of guiding fog, adjusting fog volume, and even fog falling. 15. The pressure bucket adopts Henry's law to heat and humidify, and provide the humidity required by the salt spray testing machine laboratory. 16. Opening method: Pneumatic automatic opening is adopted, The salt spray testing machine is one of the "three prevention" (humid heat, salt spray, mold) testing equipment for artificial climate environments. It is an important salt spray testing equipment for studying the adaptability and reliability of various environments in industries such as machinery, national defense, light industry, electronics, light industry electronics, and instruments. This salt spray testing machine can perform neutral salt spray tests in accordance with GB/T2423.17 "Basic Environmental Testing Regulations for Electronic and Electrical Products - Test Ka: Salt Spray Test Method", and can also perform acetate spray tests. This salt spray tester complies with CNS, ASTM, JIS and ISO standards. The salt spray test is to test the corrosion resistance of the products after coating, electroplating, Anodizing, anti-rust oil and other anti-corrosion treatments on the surfaces of various materials.
1.)Performance specifications: 1. Machine model: DL-4100, 2. Capacity: 100L, 3. Temperature range: -40 -150 , 4. Humidity range: 20% -98% RH, 5. Temperature and humidity control accuracy: ± 0.5 ± 2% RH, *Attention: The performance guarantee of items # 2-4 above should be measured after 30 minutes of stable temperature sensing 6. The temperature and humidity are evenly distributed: ± 2.0 ± 5.0% RH, *Note: The performance guarantee of item # 5 above requires testing at a distance of 1/6 of each wall surface in the testing area, and must be measured after stabilizing with temperature and humidity for 30 minutes 7. Inner box size: 500 high Width 400 500mm deep, 8. Outer box size: 1700 high Width 1000 1500 mm deep, 9. Equipment placement space: at least 2000 2000 2000mm (W H D) , 10. Power supply: AC220V 4.5KW, 50HZ
NG500 lab use nitrogen generator Product Description NG500 Nitrogen Generators Lab nitrogen gas Working Principle Nitrogen generator uses the electrocatalysis method to separate air gas Stable and pure air enters electrolysis cell and oxygen in the air is separated then left nitrogen gas is outputted Application Carrier gas for various brands of GC and GCMS Make up gas for GC Supplementary gas 3Gas for Gel Permeation Chromatograph 4LCMSLiquid ChromatographMass Spectroscopy and Thermal Analyzer 5Other field that ask pure N2 Features 1 Program control Nitrogen gas could be adjusted automatically according to usage flow under stable pressure and flow 2 Advanced technology It uses noble metal as catalyst high catalytic efficiency and large nitrogen production 3 Twolevel catalysis Oxygen content in nitrogen is less than 3ppm 4 Lower moisture in nitrogen gas Technical Parameters Model NG300 NG500 Output Flow mlmin 0 300 0 500 Output Pressure 042 Nitrogen Purity 99999 compared with O2 Input Air Pressure 04 Power Voltage V 22015Â 50 60Hz Input Power W 110 200 Weight kg
Winner2309A is intelligent full automatic laser particle size analyzer, adopt the most advanced International MIE scattering principle and Fraunhofer diffraction principle, which is integrated model of wet and dry dispersion system, High sensitive and High-resolution photoelectric probe system and imported Canon lens optical path ensure the good accuracy and repeatability of particle size distribution, It s widely used in industrial production quality control departments and research institutions. Test range:0.01-2000 microns
Description A cylindrical roller bottle is a kind of disposable container which can meet the requirements of large-scale production of cells and tissues in both experimental and industrial production and is widely used in the culture of animal and plant cells, bacteria, viruses and so on. Placed on rollers, the flask can slowly rotate and bathe cells attached to the inner surface of the bottle. Rollers are typically made of plastic or autoclavable glass and are available in a variety of capacities and styles. Product Parameter  TC Treated Item No. Size Culture area(ml) Cap Sterile pcs/pack pcs/case C022002 2L 850 Seal cap Yes 2 40 C022005 5L 1750 Seal cap Yes 1 20 Features 01 Material: polystyrene (PS), which meets USP VI medical grade. 02 Vacuum plasma surface treatment technology, enhances cell adhesion ability, and can also be coated with collagen on the inner surface according to customer requirements. 03 cGMP standard production, each batch passes the performance test, and perfect quality system from the source to ensure product quality and consistency. 04 Sterile, no endotoxin, no heat source, no cytotoxicity. 05 Injection, pull and blow molding process, the product bottle mouth is smooth and round, the contact sealing with the cap is better, and the product residue is less. 06 5L cell bottle adopts a two-stage design to increase the contact area. The contact area between the roller bottle and the rotating bottle machine adopts the frosted structure to increase the friction coefficient of the roller bottle and reduce the sliding phenomenon.
pharmaceutical glass packaging: Neutral glass tubes USP type I, clear and amber color. Glass Ampoule, USP type I Tubular Glass Vial for injection, USP type I, Molded Injectable glass vial, USP type I,II,III, Butyl rubber stopper,/Aluminum-Plastic Cap. Agent of vial-forming machine.
Light and Strong Laboratory Modular Clean Booth, also commonly known as clean work booths, clean booths, etc. They are widely used in the electronics, precision instrument processing, pharmaceutical, medical and food industries. The Light and Strong Laboratory Modular Clean Booth is a simple clean room that can be set up quickly, is quick to install, short in construction time, inexpensive and easy to move. Keeping the main production processes within a small environment is also the best choice for cleanroom design. There are various types of clean booths, such as normal draped, glass, steel, self-contained, modular, anti-static and self-contained air showers. Configuration 1. Frame: industrial aluminium (or stainless steel square, iron square sprayed plastic) as a solid, beautiful, non-rusting, non-dust producing frame. 2. Anti-static drape: anti-static drape (or toughened glass) around the four sides, good anti-static effect, high transparency, clear grid, good flexibility, no deformation, not easy to age. 3. Fan filter unit FFU: the use of centrifugal fans, with long life, low noise, maintenance-free, small vibration, stepless variable speed and other characteristics, fan quality and reliable, long working life, coupled with a unique air duct design, greatly improving the efficiency of the fan, reducing the noise. The internal purification level can reach 100-100K; especially suitable for the area with high requirements for local purification level in the workshop, such as the assembly line operation area. 4. Internal purification lamp for purification room, no dust production. Features The air is drawn in from the top of the FFU, filtered by the primary filter and the high efficiency filter, and the filtered clean air is sent out to the clean room at a uniform speed of 0.45m/s�±20% on the whole outlet surface, forming an even flow layer, so that the clean air flow is vertical and unidirectional, thus ensuring the required cleanliness in the working area. 1. Can be used individually or in combination. 2. compared with civil engineering or assembled clean rooms, the investment is small, the result is fast, the installation is easy and the running cost is low. 3. modular structure, easy to improve the cleanliness level, strong scalability, and high reuse value 4. Easy to move (universal wheels can be installed) Application The clean booth is widely used in the electronics, precision instrument processing, pharmaceutical, medical and food industries and is an indispensable piece of clean equipment for these industries.
Our company is a professional manufacturer of laboratory products, engaged in the production, development, and sales of high-tech trace analytical laboratory containers, to fill the gap in We have been in this line for about 30 years and we have our own design department and production line. We can ensure your quality and production line. OEM is warmly welcomed. We mainly produce laboratory products based on PFA materials, such as Beakers/reagent bottles/mixing bars/forceps/funnels/volume flasks/crucibles/mixing bars/water tanks/reaction bottles/washing bottles/measuring bottles, etc. Our products are sold all over the world (such as CUG, IGCAS, SGS, etc. ) And the quality of our products can be compared with foreign brands. They are well received by the experimenter in semiconductor, electronics, pharmaceutical, and other industries, and are widely used in the chemical industry. We continue to improve the quality of products and adhere to the customer, service, technology as the core. Along the way has been recognized by many customers, sincerely thank you for your support and help, but also look forward to working with you to reach a long-term cooperative relationship. In the future, we will continue to serve our customers and provide better-quality products.
Our company is a professional manufacturer of laboratory products, engaged in the production, development, and sales of high-tech trace analytical laboratory containers, to fill the gap in We have been in this line for about 30 years and we have our own design department and production line. We can ensure your quality and production line. OEM is warmly welcomed. We mainly produce laboratory products based on PFA materials, such as Beakers/reagent bottles/mixing bars/forceps/funnels/volume flasks/crucibles/mixing bars/water tanks/reaction bottles/washing bottles/measuring bottles, etc. Our products are sold all over the world (such as CUG, IGCAS, SGS, etc. ) And the quality of our products can be compared with foreign brands. They are well received by the experimenter in semiconductor, electronics, pharmaceutical, and other industries, and are widely used in the chemical industry. We continue to improve the quality of products and adhere to the customer, service, technology as the core. Along the way has been recognized by many customers, sincerely thank you for your support and help, but also look forward to working with you to reach a long-term cooperative relationship. In the future, we will continue to serve our customers and provide better-quality products.
Our company is a professional manufacturer of laboratory products, engaged in the production, development, and sales of high-tech trace analytical laboratory containers, to fill the gap in . We have been in this line for about 30 years and we have our own design department and production line. We can ensure your quality and production line. OEM is warmly welcomed. We mainly produce laboratory products based on PFA materials, such as Beakers/reagent bottles/mixing bars/forceps/funnels/volume flasks/crucibles/mixing bars/water tanks/reaction bottles/washing bottles/measuring bottles, etc. Our products are sold all over the world (such as CUG, IGCAS, SGS, etc. ) And the quality of our products can be compared with foreign brands. They are well received by the experimenter in semiconductor, electronics, pharmaceutical, and other industries, and are widely used in the chemical industry. We continue to improve the quality of products and adhere to the customer, service, technology as the core. Along the way has been recognized by many customers, sincerely thank you for your support and help, but also look forward to working with you to reach a long-term cooperative relationship. In the future, we will continue to serve our customers and provide better-quality products.
