Product introduction: 1.Using precision guide rail and the import motor to drive the blade seat conversion, printing, and high accuracy. 2.Printing scraper can rotate 45 degrees fixed up, easy printing stencil and squeegee cleaning and replacement. 3. Scraper block can be adjusted before and after the blade, to choose the right printing position. 4.Combined with a fixed groove printing platen and PIN, easy installation and adjustment, for single, double sided printing. 5.School Edition way to move a steel mesh, combined with printed (PCB), X, Y, Z. Convenient fine adjustment. 6.Can be set to one-way and two-way, a variety of printing methods. 7.With the automatic counting function to facilitate the production of output statistics. 8.Adjustable blade angle, steel blade, rubber scraper are suitable. 9.Touch screen with a screen saver function, the time can be adjusted to protect the touch-screen life. 10.Printing speed display, can be adjusted. Technical parameters Model No HR-168 Function Solid liquid ingredients fully mixing from the solder paste, to achieve the same density Running speed first rotation: 800 RPM; Secondary rotation: 600 RPM Ability to work 500g*2 tins (or customized) Can accept solder paste pot tin diameter Φ60-Φ67 standard configuration(or customized) Time setting 0.1s~9999s Display mode Microcomputer LED digital display Power supply AC220V 50/60Hz 180W
Product introduction: 1.Using precision guide rail and the import motor to drive the blade seat conversion, printing, and high accuracy. 2.Printing scraper can rotate 45 degrees fixed up, easy printing stencil and squeegee cleaning and replacement. 3. Scraper block can be adjusted before and after the blade, to choose the right printing position. 4.Combined with a fixed groove printing platen and PIN, easy installation and adjustment, for single, double sided printing. 5.School Edition way to move a steel mesh, combined with printed (PCB), X, Y, Z. Convenient fine adjustment. 6.Can be set to one-way and two-way, a variety of printing methods. 7.With the automatic counting function to facilitate the production of output statistics. 8.Adjustable blade angle, steel blade, rubber scraper are suitable. 9.Touch screen with a screen saver function, the time can be adjusted to protect the touch-screen life. 10.Printing speed display, can be adjusted. Technical parameters Model No HR-168 Function Solid liquid ingredients fully mixing from the solder paste, to achieve the same density Running speed first rotation: 800 RPM; Secondary rotation: 600 RPM Ability to work 500g*2 tins (or customized) Can accept solder paste pot tin diameter Φ60-Φ67 standard configuration(or customized) Time setting 0.1s~9999s Display mode Microcomputer LED digital display Power supply AC220V 50/60Hz 180W
Product Description 1. For internal strength generates during separation, Minimize it to value under 180uE ,to avoid solder crack or component damage 2. Able to separate edge of V-slot, minimum distance to component is 0.5mm, and max height of component is 60mm 3. Free sanding on Blade when it is worn. 4. Cutting speed is one cut per second, controlled by pneumatic foot-plate switch 5. Blade activated negative, separation route and position in control safely 6. Pneumatically driven and electric control 7. sepatation is not realized by friction, so no obvious metal residue left, 8. life is over 6000000 times 9. Air pressure 6 to 8 kg, no requirement on working environment, simple maintenance by anti-rust oil 10. Guillotine type Automatic V-cut PCB Cutting Machine for Aluminum Board and FR4 Board Parameters Model No HR-4000 Max Cutting Length 330mm Cutting Thickness 0.5 to 3.5 mm Working Pressure 0.6 to 0.8 Mpa , dry air source Max Height of Component 60mm Equipment Dimension 680 x 300 x 1100mm Working Voltage AC 220V 50~60HZ Gross weight 120KG
Product introduction: 1.The nether linear blade is used to fix the PCB V-cut ,the upper circular blade moves to separ- ate the PCB. By pressing the foot-pedal to control the action of circular blade. 2.Adopt step motor,can separate all kinds of V-cut PCBs.Max separate length 1200mm (400mm,600mm,900mm,1200mm is optional) 4.The stroke of the upper circular blade can preset .(setting rang :Between any two groups of 0,100 ,200,300,400mm ) 5.Blade moving speed can switch between 300mm/s and 500mm/s. 6.The gap between two blades is easy to adjust 7.Operation is very safe, the circular blade is covered by material ,avoid the blade hurting han for free twice.d. Also can install an sensor ,when hand or foreign matter enter into the working area,it will stop immediately. 8.Blade material is SKD-II from Japan,long lifetime.During cutting,it can effectively decrease cutting stress to avoid welding spot cracking. 9.Available PCB thickness:0.5-3.2mm 10.PCB V-cut thickness: 0.25-2.0mm Functional Specifications Function HR-3000 Machine size (LÃ?WÃ?H)mm 880*370*420mm Blade SKD - II material imported from Japan, Drive system Taiwan brand stepper motor(or customized) Control system Independent research and development (or customized) Spindle speed 200mm/s The tailgate depth adjustable range 0-150mm The largest PCB cutting width 150mm The largest PC board cut length 400mm PCB thickness 0.5-3.2mm The thickness of the V groove 0.25-2.0mm circular blade fine-turning ±0-2mm nether linear blade adjustment 0-50mm Power supply AC220V 50-60HZ Weight 60Kg
features: 1.Decrease the stress , invoide the welding pot break. 2.Adjust the up guide slip by manual, which can solve the V cut depth different problem. 3. There is the guide for V groove, which can ensure the cutting quality 4.High efficiency , V max=200mm/s. Speed is adjustable. 5.High precision, easy to maintenance, safe enough. 6.Machine is portable,high speed, easy to operate. 7.The up and down blade can be adjusted accurately,Up blade adjust : 0-15mm. 8.It can make to order, if the PCB is over height or the special PCB. 9. PCB components height limit : 20mm, under the PCB boards components height limit 10mm. Inside of the PCB max. width is 240mm, another side dont limit. 10.The length of PCB Board can be Unlimited. details 1.Coutrolled by microcomputer program, it can cut board accurately with no error. 2.This machine applies unique multi sections cutting, the cutting is to be finished by 6 pieces round blade. 3.Precise adjustment of up and down blade.Adjustable blade moving speed : 200mm/s. As per customers' need, certain speed can be set. 4.Operation platform can be adjustable higher and lower between 0 and 50mm. 5. Working process is pretty smooth, due multi sections cutting. 6.There won`t be any deviation when cutting along the v-cut slot, even the v-cut slot is shallow. 7.Pre-set the cutting start and end point to well control the cutting length Specification of multi blades cutting machine: Name multi blades cutting machine Model HR-5000 Weight Approx.60KG Voltage AC220V/50HZ Cutting speed 0-200mm/s PCB thickness 0.6-3.0mm PCB length Unlimited Power 40W PCB material Aluminum substrate, copper substrate, FR4, glass fiber board ect Warranty 1 year(exclude the balde) Packing Detailed Standard exported packing per PCB V-CUT separator Delivery Detailed Depend on order
Product introduction: 1.This unit is used to send bare PCBs into SMT production line 2.Stable and reliable PLC control system; 3.Easy to operate LED touch screen control interface; 4.Uninterrupted loading ; 5.Machine always fault monitoring; 6.Optional pass working mode; 7.Smooth and parallel width adjustment(Stainless steel leadscrew); 8.Small volume design for space saving; 9.SMEMA port is compatible;
APPLICATION: The Single magazine loader is used at the starting of the line for loading of PCBs to the production line. The unit loads the production line automatically by pushing PCBs out of a magazine onto the conveyor of the down-stream machine. FEATURES: Panasonic PLC Control system. FUJI button, or touch screen operation options available. Four pitches selections 10, 20, 30, 40mm (FUJI Button operation), multiple pitches selectable (touch screen operation). Direction from left to right, or right to left (optional). 3 magazines loading capability. CE certified. SMEMA compliant.
Product introduction: 1.Stable and reliable PLC control system 2.Easy to operate LED touch screen control interface 3.Using cylinder flip, quick, smooth, precise alignment(or use the motor for positioning) 4.Buffer deceleration design more stable, accurate 5.Optional pass working mode 6. Smooth and parallel width adjustment(leadscrew) 7.SMEMA port is compatible; Technical parameters Function This unit is used to invert PCB (180) Meet the need of two-sided machining PCB thickness Min0.6mm Cycling time Approx 10 seconds Transport direction Left to right/right to left(optional) Transport height 900±20mm(or customized) Air pressure 4-6 bar, MAX10L/minute Power supply 100-230V AC(customized) single phase, MAX 150V/A If you want more information ,feel free to contact us .Email :monica@szhonreal.com ,
APPLICATION The Bare Board Loader is used for automatically loading unpopulated boards at the beginning, or in the middle of a PCB assembly line. The bare boards are lifted one by one from the stack by vacuum and are gently lowered onto the belt segment, ready for the downstream machine. FEATURES Omron PLC Control system. FUJI button, or touch screen operation options available. By pass mode selectable. Flexible suction design, position adjustable. Sucking stability improved by using single vacuum generator system. Width adjusting system by hand crank. Electrical width adjustment available on request. SMEMA compliant. CE certified. Technical parameters Function This unit is used to send bare PCBs into SMT production line. MAX PCBâ?²s capacity 200pcs (0.6 mm thickness PCB) Cycling time Approx 6 seconds Transport direction Left to right/right to left(optional) Transport height 900±20mm(or customized) Air pressure 4-6 bar, MAX 30L/minute Power supply 100-230V AC(customized) single phase, MAX 180V/A If you want more information ,feel free to contact us .Email :monica@szhonreal.com ,
Product introduction: 1.Stable and reliable PLC control system 2.Easy to operate LED touch screen control interface 3.Using cylinder flip, quick, smooth, precise alignment(or use the motor for positioning) 4.Buffer deceleration design more stable, accurate 5.Optional pass working mode 6. Smooth and parallel width adjustment(leadscrew) 7.SMEMA port is compatible; Technical parameters Function This unit is used to invert PCB (180) Meet the need of two-sided machining PCB thickness Min0.6mm Cycling time Approx 10 seconds Transport direction Left to right/right to left(optional) Transport height 900±20mm(or customized) Air pressure 4-6 bar, MAX10L/minute Power supply 100-230V AC(customized) single phase, MAX 150V/A If you want more information ,feel free to contact us .Email :monica@szhonreal.com ,
Features: 1.Use Windows operation interface, easy to operate; 2.Leading heating mode, solve the corner when the reflow soldering welding problem, suitable for CSP, BGA, 0201 chip, and other electrical components of the welding; 3.Professional rotor design, wind speed stability, effectively prevent the PCB heating uniformity of the wind, to the repeated heating of the highest; 4.Compulsory independent loop to various temperature zones, independent PID control, and independent heating mode, make the furnace chamber temperature accurately, even, heat capacity is big. 5.Thermal insulation layer is made of high quality aluminum silicate insulation materials, heat preservation effect is good, warming faster, from room temperature to the working temperature of 15 minutes. 6.Furnace, lead-free green design; 7.High quality high temperature and high speed motor transport wind smoothly, little vibration, low noise; 8.Furnace using cylinder jack-up, safety rod support, safe and convenient; 9.The transmission way of PCB machine adopts automatic electronic speed, chain network ,synchronization, good stability; 10.Special high quality aluminum alloy guide, automatic refueling system, ensure guide rail adjusted the service life of the high precision and wide; 11.Equipped with UPS power protection function, ensure the normal output after power PCB, avoid damage; 12.Powerful software function, the PCB online temperature measurement, and analyze the data curve at any time, storing and printing; 13.PC and PLC communication with PC/PP agreement, stable work, put an end to crash; 14.Automatic monitoring and display equipment working state; 15.Special furnace design, good heat preservation, adopt special heating element, heat with highefficiency, power consumption of the lowest.
APPLICATION The Bare Board Loader is used for automatically loading unpopulated boards at the beginning, or in the middle of a PCB assembly line. The bare boards are lifted one by one from the stack by vacuum and are gently lowered onto the belt segment, ready for the downstream machine. FEATURES Omron PLC Control system. FUJI button, or touch screen operation options available. By pass mode selectable. Flexible suction design, position adjustable. Sucking stability improved by using single vacuum generator system. Width adjusting system by hand crank. Electrical width adjustment available on request. SMEMA compliant. CE certified. Technical parameters Function This unit is used to send bare PCBs into SMT production line. MAX PCBâ?²s capacity 300pcs (0.6 mm thickness PCB) Cycling time Approx 6 seconds Transport direction Left to right/right to left(optional) Transport height 900±20mm(or customized) Air pressure 4-6 bar, MAX 30L/minute Power supply 100-230V AC(customized) single phase, MAX 180V/A If you want more information ,feel free to contact us .Email :monica@szhonreal.com ,
Product introduction: 1.This equipment is used to collect bare PCBs at the end of SMT production line 2.Stable and reliable PLC control system; 3.Easy to operate LED touch screen control interface; 4.Uninterrupted loading; 5.Machine always fault monitoring; 6.Optional pass working mode; 7.Smooth and parallel width adjustment(Stainless steel leadscrew); 8.Small volume design for space saving; 9.SMEMA port is compatible; Technical parameters Function This equipment is used to collect bare PCBs at the end of SMT production line PCB thickness Min0.6mm MAX PCBs capacity 300pcs(0.6mm thickness PCB) Cycling time Approx 8 seconds Transport direction Left to right/right to left(optional) Transport height 900±20mm(or customized) Air pressure 4-6 bar, MAX10L/minute Power supply 100-230V AC(customized) single phase, MAX 300V/A If you want more information ,feel free to contact us .Email :monica@szhonreal.com ,
Technical parameter: Discriminant method Combined with weights imaging data difference analysis technology, color image contrast and color extraction analysis technology, the similarity, binary, OCR/OCV, distribution test and so on many kinds of algorithm comprehensive application camera CCD color camera resolution: 10 micro/point Light source RGB LED light source annular structure Image processing speed 0201 components
HR-SD100 is an endeavor in reverting and recycling the oxides which occur during working of a Wave Soldering Machine in order to reduce production cost, create a greener environment and assist the quality process. Use special stirring system to melt the tin residues in the tin container and separate tin and ash in the separation container by the high speed of screw rotation. 1.Characteristic: 1.Highly effective recycling of the solder waste, up to 90% yield . 2.No need to add any chemicals or reducers to the process uses physical separation to ensure a good quality product. 3.Button controls, digital temperature control sheet, accurate temperature control. 4.All-stainless steel tank, clean convenience. 5.316 grade stainless mixing bowl with an 10kg capacity with heating power for complete mixing. 6.Dross automatic feeding system, automatic feed screw. 7.Electronic liquid level alarm, manually put tin. 8.Automatic separation of tin and tin ash, into the tin and tin-ash collection device. 9.Small size, light weight, move convenience. 10.Independent smoke filtration system (Optional). 2.Technical parameters Mixing motor 1Ï? 220V 90W Mixing Heating Power 1.6KW Mixing Capacity of Bottom Tin 10KG Temperature Scope 0-350 Heating-up time 50MIN Feeding time Continuous3-4kg/15min Dimension Electrical box size L500*W250*H650 L140*W330*H390 Totol Power Consumption 1.8KW Normal running power 0.4KW Power 1Ï?220V 50Hz Net Weight Appro*45kg
Our company has accumulate nearly ten years marketing experience.The engineers could deeply know the demand of clients ,enviroment and the safety,So the most advanced technology could be integarated into the product. Tin residue is the main thing that our device facing .After the equipment processing,the dross will be refined ,and the recycled tin could be reused.This Intelligent and efficient model could be used under off-line situation ,and no worker is needed.During the working,the only thing you need to do is putting dross into the machine without any chemical .When the temperature reach 280 degree,the tin qualified for using would be purifed.By using our machine,a large mount of tin could be saved and the mount of the cost will reduce. Electronic System: 1.HITECH GUI interface:WEINTEK TAI WAN 5.7" touch creen 2.Built-in time control system: time pre-setting, automaticturn on/off 3.PID function heating mold with zero touch Dross loading system: In-phase screw scraps dross and drive it into mixing aera which equped with dross powder container of 30kg capacity. Mixing System: 1.100kg capacity with outside heating mold melting system. It maks tin warm up evenly and rapidly, save energy. 2.400W 380V 3P mixing motor uses worm wheel structure to avoid motor directly connect with high temperature part. 3.Special designed mixing structure makes dross evenly melted. 4.Temperature couple check liquid dross temperature and feedback acurately. Pure Tin Molding System: 1.When pure tin reaches to 30kg, the machine automaticly discharge the tin out to the container. 2.Molding slot: 1.3kg/slot, 16pcs slots 3.Automatic output device: in-phase with discharge sysyem to collect and output the pure solder. Inner force cooling system makes solder bar cool down in short time. Fog purify system: Water filtering + activated carbon filter cotton, filtering the smoke particles and peculiar smell gas. Body Parameters: Streamline appearance with 3D design, green arc glass to see the operation and easy maintenance. Power Supply:3P 380V /AC Size:L1800mm*W1050mm*H1600mm; Weight 500KG Power:5.8KW Working Power 1.8KW
HR-5000B Multi-Blade PCB Cutting Machine 1.This machine can cut many pieces of singles board for one time. 2.The shaft of upper blade is adjustable from 0mm to 5mm. 3.The distance between blade is adjustable, suitable to cut pcb with width from 15mm to 20mm. 4. The blade is made of Switzerland , using high speed steel, durable with long service life. 5.The cutting speed is controlled by the rotary knob. 6.No limits to the cutting length. 7. Cutting thickness is from 0.5mm to3.2mm. 8. The transfer belt can take the separated boards out, so the machine can dock the assembly line. 9. This machine is suitable for pcb control panel, fr4, aluminum base board, etc(longer than 400mm) and special board. 10. With multi-blade and easy operation, this machine fits mass production. Features: Model number: (HR-5000B) PCB Cutting Machine Dimension : 1100*1050*500mm Cutting length : No limit Cutting width : 60-200mm Cutting thickness : 0.5-3.2mm Voltage : AC230 V/110V Weight 425KG
Application: The machine is mainly used for washing, filling and capping liquid such as carbonated, and so on. Features: 1) Food-grade stainless steel 304for the washing, filling, capping unit, the pipe, fittings and other part in contact with product, meet the food industry standard. 2) PLC automatic control with world famous brands like Mitsubishi, Siemens, Omron, etc., good stability. 3) Easy machine operation by using the touch screen like Weinview or Siemens. 4)Standard machine parts, easy to do maintenance work, greatly reduce the maintenance costs and improve work efficiency. 5) Emergency stop and other safety features provide unparallel operator safety. 6) All parts and service plans available. Machine specifications are as below: Capacity(B/H) Specification Weight(kg) Machine Size(cm) 3000 DGCF16-12-6 2500 200*150*220 4000 DGCF18-18-6 3500 252*202*270 8000 DGCF24-24-8 5500 300*220*280 12000 DGCF32-32-10 8000 416*286*290 15000 DGCF40-40-12 10000 455*325*290 18000 DGCF50-50-15 12000 562*357*290
Application: The machine is mainly used for washing, filling and capping liquid such as mineral water, pure water, and so on. Features: 1) Food-grade stainless steel 304 for the washing, filling, capping unit, the pipe, fittings and other part in contact with product, meet the food industry standard. 2) PLC automatic control with world famous brands like Mitsubishi, Siemens, Omron, etc., good stability. 3) Easy machine operation by using the touch screen like Weinview or Siemens. 4) Standard machine parts, easy to do maintenance work, greatly reduce the maintenance costs and improve work efficiency. 5) Emergency stop and other safety features provide unparallel operator safety. 6) All parts and service plans available. Machine specifications are as below: Capacity(b/h) Specification Weight(kg) Machine size(mm) 100 XG-100J(100B/H) 300 1750*950*1550 150 XG-100J(150B/H) 450 1850*1050*1650 200 XG-100J(200B/H) 500 1950*1150*1700 300 XG-100J(300B/H) 750 2050*1250*1800 450 XG-100J(450B/H) 1250 2250*1450*2000 600 XG-100J(600B/H) 1750 2450*1650*2200 900 XG-100J(900B/H) 2250 2650*1850*2400
Features: - production of sub-micron or nano-sized particles with narrower size distribution; - use of small beads 0.3-2.0 mm as grinding media; - grinding barrel/agitator manufactured of alloy steel, pu or ceramic as standard materials; - turbine-agitator with pins; - dynamic separation of beads with mesh rings; - no mechanical sealing; - easy installing and maintaining; - low grinding temperature, will not pollute the material; - high grinding efficiency. -
