YCL-63 LUC-63 Fine oil filter trolley China industrial filter element hydraulic filter supplier hydraulic filter element price industrial filter element manufacturers industrial filter element factory
Technical Parameters: 1.Norminal diameter:DN15-DN800; 2.Working temperature:-30-200; 3.Filtering accurancy(mesh):10-300; 4.Seals material:nitrile-butadiene rubber(NBR),fLUORO RUBBER (FPM),Oil -resisting asbestos; 5.Working pressure:1.0Mpa,1.6Mpa; 6.Body material:carton steel ,brass,stainless steel 201,304,316.
Ycl-125 Fine Oil Filter Trolley
Filter Details Short Description PALL CORPORATION UE209AZ07Z Category Pleated Media Liquid; PALL CORPORATION; OEM Name PALL CORPORATION OEM Part # UE209AZ07Z Measurements Short Description PALL CORPORATION UE209AZ07Z Length 7.500 Outer Diameter 1.830 Inner Diameter 1.00 Request Additional Specification
Main Filter #: MF0594505 Part Type: Hydraulic Product Media: Glass Height: 16.020 OD Top: 4.370 ID Top: 2.441 OD Bottom: 4.370 ID Bottom: 0.728 Collapse Pressure (PSI): 100 Operating Temp Min (F): -13 Operating Temp Max (F): 248 Flow Direction: Inside-Out Gasket Material: Buna Fluid Type: HH / HL / HM / HV / HFD Beta Ratio 1: 200/20.7 Beta Ratio 2: 1000/26.6 Micron 1: 25 Micron 2: 27
Filter Details Short Description HANKISON E5-32-10 Category Air/Oil Separator; HANKISON; OEM Name HANKISON OEM Part # E5-32-10 Measurements Short Description HANKISON E5-32-10 Length 15.125 Outer Diameter 2.500 Inner Diameter 1.50
Filter Details Short Description TRIPLE R TR-20430 Category Misc Filters; TRIPLE R; OEM Name TRIPLE R OEM Part # TR-20430 Measurements Short Description TRIPLE R TR-20430 Length 4.500 Outer Diameter 7.100 Inner Diameter 1.57
Position: Home > Hydraulic oil filter > Replacement BALDWIN H8043 Filter Element Replacement BALDWIN H8043 Filter Element Replacement BALDWIN H8043 Filter Element Replacement BALDWIN H8043 Filter Element Filter Cross Reference: AGCO-709656 ; AVN HYDRAULICS-138570 ; BLOUNT-34635085 ; CARQUEST-84121 ; CASE-CASE IH-573201R1 ; CATERPILLAR-3I0647 ; COMPACTION AMERICA-938189 ; DIAGNETICS-LPD204B12 , LPD204V12 ; EIMCO-D2NP165006 ; Parameter Attributes Part Type: Hydraulic Product Media: Glass Height: 4.440ï¼?112.776mmï¼? OD Top: 1.772ï¼?45.0088mmï¼? ID Top: 1.004ï¼?25.5016mmï¼? OD Bottom: 1.772ï¼?45.0088mmï¼? Collapse Pressure (PSI): 305 Operating Temp Min (F): -13 Operating Temp Max (F): 248 Flow Direction: Outside-In Gasket Material: Viton Fluid Type: HH / HL / HM / HV / HFA / HFB / HFC Packaged Dimensions Gross Length 55mm Gross Width 55mm Gross Height 123mm Gross Weight 1.2KG Gross Volume 0.000372m³ Other Information
Operation Temperature: Materials:imported filter paper,PP,glass fiber,stainless steel wire mesh,etc. Filtration rating:0.1m-300m Working Environment:;Hydraulic sysytem Dimension:customized Flow rate:30-480L/min Differential Pressure:up to 480 bar Customized
MaterialImported filter paper, glass fiber , stainless steel wire mesh Differential pressureUp to 300 bar Maximum lifetime6 Months, with the change of materials Installation DimensionAccording to product type or customized Sealing materialNBR , VITON , IIR etc. CertificationISO , IQNet Factory experience14 years After-sales Service ProvidedEngineers available to service machinery customized
Filtration media:Fluid , oil ,gas Filter grades:1m-280m Material:Imported filter paper, glass fiber , stainless steel wire mesh Differential pressure:Up to 300 bar Maximum lifetime:6 Months, with the change of materials Installation Dimension:According to product type or customized Sealing material:NBR , VITON , IIR etc. Certification:ISO , IQNet Factory experience:14 years cutomized
Materials:imported filter paper,PP,glass fiber,stainless steel wire mesh,etc. Filtration rating:0.1m-300m Working Environment:Hydraulic sysytem Weight:as per size and material Dimension:customized Flow rate:30-480L/min Differential Pressure:up to 480 bar customized
We are borosilicate glass manufaturer in Hebei China,with the history more than 20 years. Borosilicate gauge glass and glass gaskets, KLINGER quality and normal price. 1.Glass size : (reflex glass and plain glass) 400 x 34 x 17 mm, 370 x 34 x 17 mm, 340 x 34(30) x 17 mm 320 x 34(30) x 17 mm, 300 x 34(30) x 17 mm, 280 x 34(30) x 17 mm 250 x 34(30) x 17 mm, 220 x 34(30) x 17 mm, 190 x 34(30) x 17 mm 165 x 34(30) x 17 mm, 140 x 34(30) x 17 mm, 115 x 34(30) x 17 mm 2.Round sight glass: all kinds of size 3.Glass gasket: non asbestos gasket, graphite gasket and mica gasket. The logo,your brand or other words can be printed on the glass according to your requirement. FREE samples will be sent if you need. Aaron AOHONG GROUP LIMITED Hengshui Aohong Technology Co.,Ltd
We can provide all kinds sight glass level gaugeg lass ,round sight glass
Transparent Level Gauge Working Principle Transparent level gauges are always fitted with two plate transparent glasses between which the fluid is contained. The fluid level is indicated as the result of the different transparency of the two media and in some cases (for water steam), by conveying upwards on to the surface of separation (between liquid and gaseous substances) a source of light located at the back of the gauge, the rays of which are totally reflected down to the observer.Transparent Type Level Gauge We can provide the corresponding level glass, please refer to the related products. APPLICATIONS Transparent level gauges are suitable for almost all installations. In fact they permit: the use of mica shields or Polytrifluorochloroethylene shields to protect the glass from the corrosive action of the process fluid the observation of interface the observation of the liquid colour This instrument consists of a metal body, machined to have an internal chamber and one or more front windows (on each side of the gauge). On each window a special high resistance plate transparent glass is applied with sealing joint and metal cover plate hold by bolts and nuts. The chamber is connected to vessel with cross fittings and flanged, threaded or welded ends. Usually, between the instrument and its connecting ends, valves are fitted to consent shut-off piping and to disassemble the level gauge without to empty the vessel. Drain valves can also be fitted to cross fittings device. To avoid leakage in case of glass breakage, safety ball-check device can be provided in cross-fittings or shut-off valves. This kind of indicator is suitable for water/steam. To protect glass surfaces from corrosive action of the process fluid, Transparent Level Gauges can be fitted with Mica shields or Polytrifluorochloroethilene shields. This kind of indicator is suitable for liquids colorless and very fluid. In some case (i.e. for water / steam) the best reading is obtained by conveying upwards on the surface of separation (liquid/steam or vapor interface), a source of light, located on the back of the gauge, the rays of which are totally reflected down to the observer.
Reflex Level Gauge WORKING PRINCIPLE Reflex glass level gauges working principle is based on the light refraction and reflection laws.Reflex Level GaugeReflex glass level gauges use glasses having the face fitted towards the chamber shaped to have prismatic grooves with section angle of 90�°. When in operation, the chamber is filled with liquid in the lower zone and gases or vapors in the upper zone; the liquid level is distinguished by different brightness of the glass in the liquid and in the gas/vapor zone. The reflex level gauges do not need a specific illumination: the day environmental light is enough. Only during the night an artificial light must be provided. The different brightness in the two zones is obtained as explained below: LIQUID ZONE This zone appears quite dark when the gauge is in operation and lighted as above said. Given the construction, most of the environmental light rays incident on the external face of the glass are quite perpendicular to said face and, therefore, not deviated by the glass. These rays reach the glass/liquid interface with an inclination of approx. 45�°. The critical angle glass/liquid is always superior to 45�°. Therefore the rays incident within the critical angle (practically the totality) are refracted within the liquid and, since the internal walls of the gauge chamber are not reflecting, the rays cannot be seen from the outside. In fact the zone will appear dark, nearly black, to the observer. GAS/VAPOR ZONE This zone appears almost silver bright to the observer. As for the liquid zone, the light rays reach the glass/gas-vapor interface with an angle around 45�°. Since this angle is greater than glass/gas-vapor critical angle, the rays are not refracted , but totally reflected making 90�° turn, thus reaching the nearest glass/gas-vapor interface again with angle of 45�°. For same reason they will be reflected and turned by 90�° towards the observer, to whom the zone will appear silver bright. APPLICATIONS Reflex glass level gauges can be used in most of the cases and offer great advantages in terms of: low initial cost, low operating cost, easy level reading. Reflex level gauges cannot be used in certain cases as for example: when the separation level between two liquids has to be read (interface). when besides the level indication, the observation of the liquid colour is required. when the process fluid is high-pressure water steam, since in this case the glass must be protected from the solvent action of the boiler water by using mica shields. when the process fluid is such that can corrode the glass (e.g. high temperature alkaline solutions or hydrofluoric acid), since ica shields or Polytrifluorochloroethylene shields must be used to protect the glass.
Round sight glass, also called round gauge glass and sight glass disc, commonly uses the material of soda-lime glass, borosilicate glass, aluminosilicate glass and quartz glass. We suggest different material according to environmental conditions, such as temperature, pressure, acid and alkali. Soda-lime glass working temperature is up to 230 �°C, but it is the most inexpensive material. Borosilicate glass is particularly used in aggressive environment, such as acid and alkali. The working temperature is up to 400 �°C. Aluminosilicate glass can resist acid and alkali better than borosilicate glass and the working temperature can reach 650 �°C. Quartz glass is the best material, whose working temperature can reach 1100 �°C. Round gauge glass is commonly used in industry, chemical, petrol and medicine pipes and flanges for observing the liquid flow and liquid level. Round glass Data Sheets Quartz round glass can be processed and produced according to customer requirements, using different materials of JGS1, JGS2 and JGS3. Round Gauge Glass for Observing Liquid Flow and LevelRound Gauge Glass for Observing Liquid Flow and Level TAGS:Transparent Gauge GlassQuartz Glass
Transparent type is also manufactured from "extra-hard" borosilicate glass. The surfaces on both sides are finely smooth and ensure optimal transparency. A) One is as same with reflex Gauge Glasses,use molds to make the semi-finished products,afterwards,ground and polish the two side to ensure optimal transparency. By this manufacturing technique,the definition isn't good. B)The other manufacturing technique is made of High Borosilicate sheet of 17mm thickness, cut the glass sheet according the detailed size and polish the side face for the smooth.This manufacturing technique glass is very clear,but the goods cost is higher. It can be used with all media at service conditions up to 6MPa and temperatures up to 430 degrees centigrade. Transparent Gauge Glass Used in Industry Pipe SIZE TypeA Weight L B S g/piece I 115 30 17 118 II 140 30 17 146 III 165 30 17 176 IV 190 30 17 200 V 220 30 17 237 VI 250 30 17 265 VII 280 30 17 303 VIII 320 30 17 334 IX 340 30 17 359 X 370 30 17 391 SIZE TypeB Weight L B S g/piece 0 95 34 17 110 I 115 34 17 132 II 140 34 17 162 III 165 34 17 195 IV 190 34 17 228 V 220 34 17 264 VI 250 34 17 301 VII 280 34 17 338 VIII 320 34 17 387 IX 340 34 17 410 X 370 34 17 461 Green Plain Gauge Glass Transparent Gauge Glass Used in Industry Pipe This green gauge glass is a kind of used in the field of petroleum, chemical industry, metallurgy, electric power, food, medicine. In the other two sides fired green glass glaze. According to the optics refraction principle, in the absence of liquid, from the glass facade, can clearly see the green color on the surface. When the fluid in the liquid level meter, the refractive index of glass and liquid is the same, the color will not be reflected, can see the white. The sizes are all customized according to clients' requests.
Dear my friend, Nice to meet you. This is Rose from Hengshui Aohong Technology Co.,Ltd. We are a professional factory of gauge glass & sight glass. Our products have been exported to many countries. The products are as follows: 1. Reflex gauge glass ( 3 lines 4 grooves ) & Transparent gauge glass 340 x 34(30) x 17mm 320 x 34(30) x 17mm 280 x 34(30) x 17mm 250 x 34(30) x 17mm 220 x 34(30) x 17mm 190 x 34(30) x 17mm 165 x 34(30) x 17mm 140 x 34(30) x 17mm 115 x 34(30) x 17mm 420 x 34 x 17mm 370 x 34 x 17mm 300 x 34 x 17mm and some other special size gauge glass can be customized according to your drawings. 2. Sight glass: round, Rectangular & square , tubular sight glass 3. Glass road stud,reflective glass road studs, reflective road studs. 4. Material: tempered soda lime glass, tempered borosilicate glass, tempered borosilicate 3.3, quartz. 5. Packing: paper box, carton , plywood case. or according to requirement. 6. Gasket: asbestos rubber gaskets ,non-asbestos rubber gaskets, graphite gasket,PTFE gasket,micashield . 7. Printing: we can print on the glass according to requirements. Any question, please feel free to tell me. I will do my best! Thanks&Best regards,
Round Glass The borosilicate round glass is produced according to the international standard DIN7080. Operating temperature is 280 degrees Celsius. In a toughened form, temperatures up to 315 degrees Celsius are possible whilst annealed glass may be used up 400 degrees Celsius continuously with a short term maximum of 500 degrees Celsius. In addition to the standard DIN size, other sizes can be customized.
