Cnc engraving machine-jk-40j-d JK-40M Table Size: 480*380mm Working Stroke of X, Y, Z: 400*300*90mm Positioning Accuracy of X, Y, Z: í+0.01/300mm Repositioning Accuracy of X, Y,Z: í+0.01mm Evenness of Worktable: í+0.025/300mm Verticality of X, Y: 0.025/300mm Spatial Height in Z Direction: 200mm Spindle Power: 200w Spindle Speed: 1000-2500rpm Driving System: Stepped Working Voltage: Single Phase 220V Weight of Machine Tool: 700kg Dimension: 800*780*1450mm wooden package. 1000x1000x1600MM
Jaw Crusher is mainly used to crush kinds of mining stones primarily, and the largest compression resistance of the material to be crushed is 320MPa. The jaw crusher is widely used in mining, metall-urgical industry, building material, highway, railway, and chemical industry. Working Principle of Jaw Crusher: The motor transmits power through belt, drives the moving jaw do periodic motion to the fixed jaw surround the eccentric shaft. The angle between toggle plate and moving jaw increases when moving jaw moves up. So the moving jaw closes to the fixed jaw. The stuff will be crushed in this process. The angle of Jaw Crusher between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw of Jaw Crusher moves away from fixed jaw by the pulling of rod and spring, the products after crushing will be discharged from the outlet of Jaw Crusher. Characteristics of Jaw Crusher: High ratio of crushing, homogeneous final grain size, simple structure, reliable working condition, easy maintenance, low operating cost. standard packing
Impact Crusher is mainly used to crush many kinds of large, medium, small materials whose side length is less than 500mm, and compression resistance should not be more than 350Mpa. The impact crusher is widely used in hydroelectricity, highway, artificial stone and sand, building material, etc. Working Principle of Impact Crusher: When the impact crusher works, the motor drives the rotor rotate of the impact crusher with high speed, on the rotor where installed the hammers. When the materials get into the area which the hammers effect, under the impact function of the hammer at a high speed, the materials are thrown to the impact device above the rotor continuously. And then the materials are rebounded from the impact liner to the area where the hammers effects for being recrushed. The materials from large to small all to be crushed at the impact chamber repeatedly. The process woní»t stop till the material are crushed to the required size and then discharged from outlet of the impact crusher. Characteristics of Impact Crusher: Special structure, connected without key, high chrome hammer, unique impact liner, deal with hard material, high efficiency and save energy, cubic shape of product, adjustable output size. standard packing
The ball mill is a key equipment to grind the crushed materials, and the ball mill is widely used in powder-making production line including cement, silicate, new-type building material, refractory material, fertilizer, ore dressing of ferrous metal and non-ferrous metal, glass ceramics, etc, and the ball mill can grind various ores and other materials with dry type and wet type. There are two kinds of ball mill, grate type and overfall type due to different ways of discharging material. Working Principle: The ball mill is a horizontal rotating device transmitted by the outer gear. The materials are transferred to the grinding chamber through the quill shaft uniformly. There are ladder liner and ripple liner and different specifications of steel balls in the chamber. The centrifugal force caused by rotation of barrel brings the steel balls to a certain height and impact and grind the materials. The ground materials are discharged through the discharging board thus the grinding process is finished. Standard packing
CNC Cutting Machine Main technical specifications and devices of the machine 1. Overall dimension: please see fig. 4, fig. 5, fig. 6 and fig. 7. 2.Track length: 26000mm, the effective cutting length is 24000mm. 3.Track width: 5000mm, the effective cutting width is 4200mm. 4.Driving mode: double-side driving 5.Cutting speed: 50 ~ 6000mm/min. 6.Max. Rapid speed: 18000mm/min. 7.Main cutting device: 1 set of single flame torch, a set of automatic height control system and a set of automatic ignition system. 8.1 set zinc powder marking torch. 9.Adjusting range for up-and-down of torch: 200mm 10. Gas for flame cutting: oxygen-acetylene or oxygen-propane or lpg Flame cutting thickness: 6 ~ 120mm 12. Strip cutting device: 4 strip-cutting torches are equipped on the back of the beam.
Cncpipeprofilecuttingmachine I.Maintechnicalspecifications 1.Outerdiameterofpipetobecut:75~1010mm 2.Max.Wallthicknesstobecut:50mm(oxy/ace), 25mm(plasma) 3.Borediameterforsteelpipegoingthroughspindle:200 4.Steelpipecuttinglength:12000mm 5.Numbersofcontrolaxis:5 6.Themax.Travel:10000mminxdirection 600mminydirection 400mminzdirection 7.Cuttingspeed:10~2000mm/min. 8.Angleofgrove:n60 9.Themax.Rotaryangle: W:limitlessrotation(piperotating) B:70(torchswayedangle) 10.Plasmacuttingfunctioncanbeequipped.
High speed Nominal pressure:450kN Nominal pressure stroke:1.6mm stroke length:10mm/20mm/30mm No .of stroke per minute:150-550/150-500/150-450 Max.height space :265mm/260mm/255mm die hight adjustment:50mm throat depth:235mm bolster surface:F.B*L.R 450mm*740mm slide surface :F.B*L.R 290mm*340mm stemhole:50mm*75mm distance between uprights:300mm thickness of bolster:110mm air pressure:0.5MPa weight:4000kg F.B*L.R*height:1620*1353*2471
Nominal pressure:4000kn Nominal pressure stroke:13mm Stroke length:400mm No .Of stroke per minute:15 Max.Height space :900mm Die hight adjustment:400mm Thickness of bolster:180 Bolster surface:f.B*l.R 2800mm*1600mm Weight:91500kg F.B*l.R:3850*5700
Used wheel loader
Rolling mill Specification of the steel rolling machine 650mm, 500mm, 450mm, rough rolling mill group, 400mm rough rolling mill group and medium rolling mill group, 320mm medium rolling mill group , 300 medium rolling mill group , 280mm, 250 mm, 220 finishing rolling mill group (note: all the groups include motor, speed reduction unit, link-up, guide rail, roller etc.) Rolling steel products: I-bar , angle bar , u-bar, round bar, deformed steel bar;, strap steel, rail steel, steel for agricultural-purpose etc.. Iii.Types of service: 1.Providing model , design, manufacture, installation and commissioning as to the requirements of the customers. 2.Providing the plane design, general layout of the equipment; process design and products design of steel rolling etc. Various technical design. 3.Dispatching various technical staff to the site for the technical services till the finished products as to the requirements of the customers. 4.Providing long-term technical service to the customers as to their requirements, mainly adjustment of steel rolling mill, new products development, equipment maintenance and improvement.
Alrflow sieving machine Ws series air flow griddle abandons geopotential working principle, adopts the working principle of kineticenergy to do works, with the air as carrier, . Mixes materials with the air under pressure, then make them to enterinto the middle of wheel, spay through the net with the enough eccentricity powder, and are collected by the snail shell. For those, which cannot through the net, are discharged automobile through exclude to gain filtration propose. Wooden case
Roller crusher Roller crusher is widely used by cement plants in China and India
Features: 1) Speed can reach 50m/min 2) Two-motor drive system ensures quick, even, stable operation 3) Highly accurate gears allow for engraving characters as small as 1.5mm 4) The subdivision, stepper motor, and the high power main shaft make the machine more efficient 5) The vacuum cleaning system offers a clean working environment and better quality 6) USB ensures high speed and efficiency 7) The unique calculating system realizes speedy, accurate, curvy operation 8) Applicable areas: a) Furniture processing industry b) Decoration c) Wooden art crafts d) Wood furniture engraving Specifications: 1) Product model: 1,325 2) Dimensions: 1,300 x 2,500 x 120mm 3) Working speed: 50m/min 4) Distinguishing rate: 0.01mm 5) Interface: USB 6) Voltage: AC380V 7) Power of the main shaft: 3kW, 4.5kW (optional) 8) Cutter diameter: 3.175, 6, 12.7mm (optional) 9) Power of vacuum cleaner: 2.2kW wooden case
1)Machine body : whole cast iron or cast aluminum 2) Work size: 300 x 300 x45mm 3)Boday size:600 x600 x600mm 4) Z axis working area:45mm 5) Max. feeding height: 60mm 6) Thickness of material:
Features: 1) Lathe bed is cast wholly and firmly and will not deform 2) Imported ball screw rod and round guide rail to ensure accuracy 3) Subdivision stepper motor with excellent performance, quick speed, stable operation, and large cutting movement to ensure long and safe operation 4) Frequency conversion water-cooling large power motor, low noise, even speed 5) Humanistic design, the machine can be disassembled, so it is easily transported 6) Applicable to: a) Chest species b) Tablet species c) Building models d) Signs e) Metal f) Wooden models g) Embossed pictures Specifications: 1) Working travel: 600 x 800 x 100mm, 800 x 1,000 x 100mm 2) Maximum carving speed: 6,000mm/min 3) Main shaft: 1,500W 4) Speed of main shaft: 0-24,000rpm 5) Cutters of main shaft: 3.175mm, 6.00mm 6) Power source: AC 220/50Hz 7) Drive: stepper 8) Weight: 200kg, 248kg Wooden Case
Lg450 cold rolling mill Technical parameter Main parameter of rolling materials Stainless steel tube, carbon steel, titanium and alloy tube Outer diameter of tube blank 250480l Wall thickness of tube blank 1035l Outer diameter of finished products 219450l Wall thickness of finished products 628l Operating length of pass 960 mm Length of the rough pipe 3-10mm Journey length of the machine frame 1208mm Journey times of the machine frame 2050¦e/+÷ Entering quantity of bend handle 600mm Diameter of roller 7801080l Entering amount 3-12mm Power of main motor 950kw Rolling lines single Loading method side loading Export package standard
Mongline long stroke cold pilgering mill Description Technical parameter: 1.Main parameter of rolling materials Stainless steel tube, carbon steel, titanium and alloy tube 2.Outer diameter of tube blank 130270l 3.Wall thickness of tube blank 632l 4.Outer diameter of finished products 108250l 5.Wall thickness of finished products 328l 6.Length of the rough pipe 2000-8000mm 7.Journey length of the machine frame 1078mm 8.Journey times of the machine frame 2555¦e/+÷ 9.Entering quantity of bend handle 535mm 10.Diameter of roller 780l 11.Entering amount 2-12mm 12.Power of main motor 550kw 13.Rolling lines single 14.Loading method side loading 15.Efficient length of rolling groove 960 mm Export package standard
3 in 1 precision servo straightener uncoiler Electric eye loop control system Straightener opener device Feeding line easily adjusts by advance worm gear screw jacks device Feed and staightener rolls with a hard chrome finished Coiler material entry support assembly Tranformer 3 in 1 servo straightener feeder and uncoiler
Metal scrap hydraulic briquette press Y83-160A Y83-230 Y83-300 YA83-300 Wooden case
Lz sand washing & recycling machine is based on sand washer and sand recycling system main tech, we make it a compact multiple function sand washer. It is widely used for crushed sand, river sand, lake sand or sea sand washing, screening, recycling and dewatering. Working principle *washing: the bucket is driven by the motor through the reducer and rotates in circle. There are many sand storage web grooves and bucket screen for sand storage and primary dewatering. When the bucket moves, sand can be put out by sand storage web groove after being cleaned in the cleaning tank and primary dewatered on the bucket screen. *recycling: flowing slurry water is extracted by slurry pump, fine sand is collected by the centrifugal force of the cyclone, then fed to the polyurathane screen from the apex spray. The 0.16-3mm fine sand and water are efficiently separated through the vibration screen. *dewatering: coarse sand (3-10mm) and fine sand (0.16-3mm) are fed onto polyurathane vibrating screen for dewatering. Technical 1.Higher sand quality, lower moisture content. 2.Recycled fine size 0.16-3mm sand, lower mud content. 3.Compact structure, multiple functions, easy install, convenient maintenance, small occupation area. 4.High capacity, after this machine 95% sand can be washed. 5.Solve sedimentation tank cleaning problem, higher economical profit.
