Pneumatic clamping of the glass sheet during the drilling operation of Opposite drilling head.BZ0213 glass drilling machine is equipped with a glass supporting table. Major Technical Specification Drilling Hole Diameter 4-130(mm) Glass Thickness 2-20(mm) Space Between Drilled Hole Center And Vertical Post 1050(mm) Total Power 1.7(kw)/2.2(kw) Dimension 1.65x2.6(M) Weight 900(kg)
It can grind and polish flat edge with arrises. It adopts mechanical stepless speed adjustment and can be adjusted to suit different thickness glass. Major Technical Specification Speed 0.5-5(m/min) Max. Grinding Amount 3(mm) Glass Thickness 3-25(mm) Min. Glass 80x80(mm) Total Power 22.8(Kw) Dimension 6.6x1.1(M) Weight 2850(kg) Max. Glass 3000x3000(mm)
BQ2500 Glass horizontal washing & drying machine is working for various flat glass and specially working for LOW-E glass. The structure of machine is made of painted steel; All parts in contact with water are waterproof materials made. The machine equipped with 4 pair of brushes and air-knife so that generate a perfect washing and drying, All driven-rolls are steel made, suitably coated with vulcanized and rectified rubber, soundproof blower, is placed on the top of drying section, to ensure a strong force air for drying. The washing section is well controlled by PLC, and it is able to be completed lift up or low-down for the purpose of different thickness of glass. W26 horizontal washing machine is an particular design for Low-E glass and other coated glass, it is also can perfectly perform washing and drying for all kind of flat glass. Min. Size 300*350mm Max.Size (Width) 2600mm Glass Thickness 3-60mm Processing Speed 1.2-6m/min Intalled Power 39KW No. of Burshes 4pairs Dimension 8500*4500*3500mm Weight 4500kg
KV9 Glass Flat Edger & Variable Miter Machine 1. Brief Introduction: 1.1. This glass edger and variable miter machine is able to grind and polish the miter angles of the glass, with bottom edge polishing and rear seaming all at the same time. 1.2. The control system of this glass miter machine uses a Mitsubishi PLC control unit. 1.3. The input and output conveyor adopt timing belt which can improve the transmission precision. 1.4. The processed glass surface is very bright and smooth, approaching the original glass surface. 1.5. The mitering angle of the glass machine ranges from 0 to 60 degree. 2. Technical Parameters 1. Processing glass thickness: 3~~25mm 2. Miter angle: 0íp~~60íp 3. Min size processing glass: 80mmí-80mm 4. Processing speed: 0.75~~3.75m/min 5. Installation power: 20.3KW 6. Size: 7800 x 1400 x 2500mm
KV11a Glass Flat Edger & Variable Miter Machine 1. Brief Introduction: 1.1 This glass mitering edging machine is able to process and polish all miter edge, bottom edge and arris on glass at one time. There are 3 wheels for each arris. 1.2. The control system of the glass mitering edging machine uses a Mitsubishi PLC control unit. 1.3. The input and output conveyor of the machine adopt timing belt which can improve the transmission precision. 1.4. The mitering angle ranges from 0 to 60 degree. 1.5. Different options: Digital display, PLC. 2. Technical Parameters: 1. Processing glass thickness: 3~~28mm 2. Miter angle: 0íp~~60íp 3. Min size processing glass: 80mmí-80mm 4. Processing speed: 0.75~~3.75m/min 5. Installation power: 23.3KW 6. Size: 7920 X 1400 X 2500mm
2-19 mm thickness 1830*1650 1220*1830 900*1780 1685*1100 1100*1620 2140*3300 2250*3300 2440*3300 2140*3660 2250*3660 2440*3660 4500*3050 6000*3050. And so on... Packing in wooden crates with powder interlayer.
As one of the leading manufacturers of frp products in china, we are specialised in manufacturing frp profiles by pultrusion process. Our products mainly include:round tube, square tube, rectangular tube, channel, angle, i-shape, t-shape, flooring pannel, gratings. After proper combination and connection, these profiles can constitute many kinds of structure or construction, such as ladder, stairs, bridge, companionway, platform. Our ladder include vertical ladder and gradient ladder, both of which can meet the standard of bs 4211-2005. Comparing with ladders made of traditional material, the frp ladder has many superior characteristics as follows. A) corrosion resistance B) insulation electrically & thermally C) non-magnetism D) rodent proof E) high strength & light in weight F) easy assembly, no welding G) nice appearance H) low maintenance I) long service life Pallet, cargo container
Class type: float glass, tempered glass, reflective glass, low-e glass etc. Pvb or glass color: clear, bronze, grey, green, milky white, french green etc Thickness: 3+0.38/0.76+3, 4+0.38/0.76+4, 5+0.38/0.76+5, 6+0.38/0.76+6 etc Feature: safety glass, sound insulation, anti-uv, energy saving Application: curtain wall, door, windows, balconies, elevators, railings, and skylights Size: 2440x1830mm, 3300x2134mm, 3300x2250mm, 3210x2250mm, 2134x1650mm, 2200x1650mm Strong wooden crates
ITO glass have many characteristic such as high-transmissivity, high infrared reflectivity, high UV-blocking-rate and low surface resistance. The thin films used for ITO is a typical transparent heater surface to help prevent fog and frost. It was a low-E glass. Which is effective in heat insulation, energy conservation. It is used for automobile, trains, plane and other transports' windshield, display window, visible refrigerator, refrigerating showcases and construction field. Passivation layer, substrate, silicon dioxide. Package: wooden case and interleaving paper between sheet Classification: Building glass,
Technical data of water jet cutting machine The machine has three parts: cutting table, intensifier pump, controller 1) We have two kinds of cutting table: bridge style and flying arms style, their technical data is as follows: Z-axis journey is 150mm Three-axis control, Auto zero positioning Way of drive : Servo ( drives and motors are FUJI brand from Japan ) All screw and linear guide are ABBA brand from Taiwan Control accuracy: í+0.01mm Cutting accuracy: í+0.2mm 2) The intensifier pump we introduce you to use is made in China, its technical data and components are as follows: Type of pressurization is hydraulic. (The water is pressurized by using the fluid pressure intensification principle) Max. oil discharge is 90 L/min Max. water discharge is 3.7L/min Max. diameter of orifice is 0.3mm Max. operating pressure is 380MPa Continuous operating pressure is 330MPa Power requirement : 37KW,380V/50HZ Type of shift is electronic maintenance free accumulator whose capability is 1.3L using American technology intensifier is from America 3) For the controller,we research and develop our own professional software, components are as follows: EVOC brand Industrial Personal Computer and 17BENQ LCD specialised waterjet cutting software Omron brand PLC instead of relay Windows XP based. Soft packing.
Clear float glass
Laminated glass - (clear and tinted) Thickness: 3mm-19mm Max size:2440mm*7000mm.
Tempered glass Thickness:3-19mm Max Size:3000*11000mm.
Insulated glass Max size: 2440*5000mm.
Compact, robust Safe, ex-proof Power source:compressed air Max.Output pressure:100mpa Medium:oil, water, corrosive liquids Hydraulic power packs include lbs130wl model are complete hydraulic units ready for connection which are provided for generating operating pressures up to 100mpa.It is suitable for powering a variety of medium, such as oil, water or corrosive liquids. As the pressure will be generated by means of a pneumatically operated pump.The electric connection will not be necessary. To operate this system, the air driven liquid pump have to be equipped with the air control unit combined filter and water seperator, pressure-regulating valve, pressure control gauge as well as manual relieve valve.In this operation, the pump will be mounted to the stainless steel tank in the closed cabinet in a compact and space saving manner.Pressure gauges, valves and pressure regulators will be fitted on panel. The desired operating pressure can be attained by adjusting the driving air pressure.When the driving air pressure and the output pressure reach the balance, the pump stops filling pressure and the output pressure stays at the preset value. This hydraulic unit can be used for all kinds of pressure testing and test tools for research and test institutes or for other functions requiring a determined pressure As per buyer's requiement
Air driven gas booster Rugged, efficient Pressure range:1.6~80mpa Seven pressure ratios available Best price, high quality Air driven gas boosters are high pressure reciprocating pumps used for gases boosting, driven of compressed shop air. Sta series boosters are single acting, single air head driven type.(except model sta02 and sta05.They are double acting models).They have to be prepressurized at the inlet port so as to meet with the outlet pressure requirements, which value will be variable based on the permitted maximum outlet pressure. Sta series gas boosters are suitable for the oil free compression of air and industrial gases like nitrogen, helium as well as flammable and risk gases like hydrogen , oxygen and natural gas.Air drive pressure from 1bar(14.5psi.) to 8bar(116psi.). Provide for operating pressures up to 80mpa. As per buyer's requirment
Silicone rubber coated fiberglass sleeving
Size:1830x240 Thickness:3mm-12mm Crates /case
1). Tempered glass is high grade float glass which is processed by special methods. 2). Have a high impact strength and great intensity to improve 3). If broken, the particles and debris will not harm the human body is an ideal choice for safety glass. 4). Can be used in flat-type building and around the doors and windows, walls, screens and home decoration, shower room , and so on . Paper interlayer between two sheets, wooden crates with strong bottom plank and polythene wrapping on crates to avoid moisture.
Description: 1). Tempered glass 2). Shape: can be round or rectangular 3). Size: as your requirements 4). Can do some designs on it Paper interlayer between two sheets, wooden crates with strong bottom plank and polythene wrapping on crates to avoid moisture.
