High Frequency Radar Level Meter Design features: Small antenna size, easy to install; non-contact radar, no wear, no pollution Hardly affected by corrosion or foam; hardly affected by changes in water vapor, temperature and pressure in the atmosphere. Severe dust environment has little influence on the work of high frequency level gauge. Shorter wavelength, better reflection on inclined solid surfaces The beam angle is small and the energy is concentrated, which enhances the echo ability and helps to avoid the interference. The measurement blind area is smaller, and good results can be obtained for small tank measurement. High signal-to-noise ratio, even in the case of switching, can achieve better performance High frequency is the best choice for measuring solid and low dielectric constant medium Application: various corrosion liquid Antenna material: PTFE Measurement range: 10 m Process connection: thread, Flange Medium temperature: -40C --130 Process pressure:-0.1~0.3MPa Accuracy: ±5mm Power supply: 24VDC (two lines, four lines) Protection grade: IP67 Frequency range: 26GHz Explosion-proof grade: Exia C T6 Ga/ Exd ia IIC T6 Gb Signal output: 4. 20mA/HART (two / four) RS485/Mod bus
This instrument is developed and designed according to the national power industry standard DL/ t506-2007 "insulation gas humidity measurement method for sulfur hexafluoride electrical equipment" and adopts the imported high-precision dew point sensor and new digital circuit control technology. It is a high-precision intelligent instrument to measure the trace moisture content in SF6 gas. This instrument adopts intelligent self-calibration technology wide measurement range fast response high accuracy good linearity dynamic display of measurement curve. At the same time the instrument also has an automatic dryer which can greatly reduce the measurement time. Product nickname intelligent micro water meter micro water meter micro quality meter.
Tank feeding bulk powder Tank Loading Mass Flow Meter realizes quantitative and accurate loading and one-button operation of powdered bulk materials, greatly improves loading efficiency, saving labor costs and improves working environment. At the same time, combining with other intelligent automation devices, the bulk powder process is fully automated, which is a new type of environmentally-friendly quantitative loading equipment. Applicable: cement, fly ash, mineral powder, alumina powder, calcium carbide powder, etc. Accuracy: ±1.0%; Flow rate: 250~800m³/h Product Features 1. Like a gas station, loading as required quantity; 2. One button to start loading automatically; 3. Since the release process is automatic and stable, accurate loading, the equipment can protect the environment and improve the working condition; 4. Height of 700mm is enough for installation, and the modification period is as short as 1-2 days; 5. It can be connected to Fengbo intelligent cloud service platform to realize early diagnosis, early warning, remote guidance and rapid maintenance. There are more than 300 successful applications and a thousand sets are installed in the cement, power, and metallurgy industry.
Function 1.Observe stress distribution in transparent plastic, glass products and optical crystals 2.Measure retardation caused by internal stress in glass and optical crystals Detecting object 1. transparent glass products with complex construction. such as : penicillin bottle, ampoule , mobile phone cover, light tube, light bulb,solar glass ,automobile glass,sapphire, glass container , glass handicraft 2. transparent plastic samples plastic bottle , cosmetic bottle , beverage bottle, contact lenses, plastic tray plastic film 3. optical crystals such as quartz , SiC, calcium fluoride Detecting methods Sensitive Color Method and Senarmont Method Specification Model PSV-413 Size W291D384H388mm Measuring range 0-280nm Weight 11Kg Viewing field W200D200mm Measure height max259mm Light Source Warm white LED light 10W Power DC 12V(with a AC/ DC adapter)
CARACTERISTIQUES DES COFFRETS Coffrets pour kit monophas
DDSY1598 Compteur d'nergie de paiement anticip de clavier BS monophas La description
Our STS prepaid electricity meter is certificated by STS association that is from South Africa. The meter is built-in prepayment algorithm, will cut off the power automatically if the credit in the meter be used up. And will reconnect automatically if the meter recharge for his meter. This kind of meter is very popular on the Africa and Asia, Nigeria, Tanzania, Ghana, Syria Indonesia, installing millions of STS keypad prepaid electricity meter.
Our STS prepaid electricity meter is certificated by STS association that is from South Africa. The meter is built-in prepayment algorithm, will cut off the power automatically if the credit in the meter be used up. And will reconnect automatically if the meter recharge for his meter. This kind of meter is very popular on the Africa and Asia, Nigeria, Tanzania, Ghana, Syria Indonesia, installing millions of STS keypad prepaid electricity meter.
The Cellular Electricity Power IoT RTU is a powerful smart meter used for power internet of things solution, is special using for remote monitoring 100~400VAC of 3-Phase electricity power distribution safety and measurement, can measuring the 3-phase 3-wire, 3-phase 4-wire distribution power voltage, current, factor, watts, frequency, apparent power, active power, reactive power, active energy, reactive energy. Also, it provides Dual SIM, 2 digital inputs, 2 relay outputs, 1 ambient sensor input for monitoring onsite temperature and humidity, also 1 RS485 for extend I/O to monitoring oil level and temperature or read meters. 1. Can be operated from anywhere, no distance limitation; 2. Quad band 850/900/1800/1900Mhz GSM GPRS Module inside. 3. 3G/4G/NB-IoT Modules are optional, LCD Display is optional; 4. Modular design, can easily upgrade the cellular module if network upgrade; 5. Embedded ARM�® Cortexâ?¢-M4 32 Bit RISC Core, 168 MHz inside, RTOS system, reliable performance with anti-jamming and in-built watchdog; 6. High isolate voltage, current and voltage input signal isolated by accuracy transformer, afford arrive DC2500V; 7. Working Voltage: 60~500VAC or 70~800VDC; 8. 3-phase 3 wires or 4 wires power parameter measurement, include voltage, current, factor, watts, frequency, apparent power, active power, reactive power, active energy, reactive energy, phase loss; 9. Measurement range: AC100~400VAC, currant range: 5A, other range should use CT; 10. 2 digital inputs, compatibles dry and wet contact, 2 relay output (5A/30VDC, 5A/250VAC), compatibles pulse outputs; 11. 1 ambient sensor input for monitoring onsite temperature and humidity ; 12. 1 RS485 port, supports Modbus RTU Master and Slave, can be used to extend I/O ports or meters; 13. Provides 1 channel DC power source output for external device, saving wiring cost; 14. Each parameter can setup threshold, when exceed or recovery will alarm immediately; 15. Can monitoring phase loss, when occurs will alarm immediately. 16. Inbuilt inter-lock logic programmer and powerful timer program function. 17. Resend the data while communication failure and alert to users by SMS; 18. Inbuilt TCP/IP protocol stack, supports cloud, APP and web server applications; 19. Supports Modbus TCP, Modbus RTU protocol and transparent transmission, can be used as master and slaves, can integrate to SCADA, HMI, DSC directly; 20. Supports USB setting, reading, records inquiry and firmware upgrade;
Description UT200+ series handheld automatic range true RMS clamp meter, designed according to safety standard EN61010-2010 CAT II600V/CAT III 300V grade, with full-function gear anti-burn protection, can meet high reliability and high safety operation requirements; It contains the basic functions of electrical measurement, with high precision measurement, and expands the current frequency (UT201+ / UT202+ only), high voltage frequency function, UT202+ has temperature measurement function, UT203+ has DC current measurement function, and the new design makes it An excellent measurement tool for electronic and electricians with superior performance Features: Large screen LCD display, fast ADC / analog to digital converter Full-featured false detection protection, overvoltage, overcurrent alarm prompt True RMS; voltage measurement 600V With high voltage frequency measurement AC current measurement function With current frequency measurement function (UT201+/UT202+UT202A+ only) Temperature measurement function (UT202+/UT204+ only) Capacitance measurement function (UT202+max 4mF/UT203+max 40mF/UT202A+/UT204+max 60mF) NCV electric field detection with sound and light alarm prompt; LIVE live line measurement (UT202A+/UT204+ only) Specification Range UT201+ UT202+ UT202A+ UT203+ UT204+ AC current (A) 400A (2%+10) (2%+10) (2.5%+5) 600A (2%+10) (2.5%+5) AC current frequency (Hz) 50Hz~100Hz (1%+5) (1%+5) (1%+5) DC current (A) 400A (2.5%+5) 600A (2.5%+5) AC voltage (V) 600V (0.8%+5) (0.8%+5) (0.8%+5) (0.8%+5) (0.8%+5) AC voltage frequency(Hz) 10Hz~10kHz (1%+5) (1%+5) (1%+5) 10Hz~60kHz (0.5%+2) (0.5%+2) DC voltage (A) 600V (0.5%+2) (0.5%+2) (0.5%+2) (0.5%+2) (0.5%+2) Resistance (�©) 40M�© (0.8%+2) (0.8%+2) (0.8%+2) 60M�© (0.8%+2) (0.8%+2) Capacitance (F) 4mF (4%+5) 40mF (4%+5) 60mF (4%+5) (4%+5) Temperature () -40~1000 (1.5%+5) (1.5%+5) Frequency (Hz) 10Hz~10MHz (0.1%+4) (0.1%+4) (0.1%+4) Features Display count 4000 4000 6000 4000 6000 Auto range Jaw opening 28mm 28mm 28mm 28mm 28mm True RMS NCV Live wire test Continuity test Diode MAX/MIN Relative mode Zero mode Data hold Low battery indication Auto power off General Characterisitics Power 1.5V battery (R03) x 2(Not included for air shipping) Display 37mm x 25mm Product color Red and grey Product net weight UT203+:235g Product size 215mm x 63mm x 36mm Standard accessories UT203+: test leads, Standard individual packing Gift box, Carring bag, English manual
UNI T True RMS Digital Multimeter 6000Counts Auto/ Manual Range AC/DC Tester UNI T True RMS Digital Multimeter UT15B /UT17B PRO 6000Counts Auto/ Manual Range AC/DC 1000V/10A Resistance Frequency Diode Frequency Diode Temperature VFC Tester Backlight Data hold Flashlight UT15B PRO / UT17B PRO is a high-reliability true RMS digital multimeter.The product has a built-in VFC anti-jamming start mode, which can filter out the carrier frequency interference or distortion voltage signal superimposed by the sine wave, and stably measure the output voltage of the inverter. And equipped with a hand-automatic backlight induction self-starting function. UT17B PRO has added frequency and duty cycle modes, which can switch frequency and duty measurement arbitrarily between DC / AC. It is also equipped with a temperature measurement function with a resolution of 0.1 The full range of functions of this series of products realizes the misdetection protection of up to 30KVA energy, ensuring users are safer and more reliable in operation,and obtained CETLus certification according to the CAT III 1000V / CAT IV 600V safety level. Features 1.6000 display digits / true effective value measurement range is wider 2. Large screen LCD display, easy to read data; 3.1000V AC / DC voltage measurement 4. VFC frequency conversion voltage measurement 600V (low pass) strong anti-interference; 5.LED flashlight, automatic induction backlight, to deal with dark environment 6.60M resistance measurement / 6000uF capacitance measurement 7.100kHz frequency / duty cycle (UT17B PRO only) 8. Temperature measurement (UT17B PRO only) 9. Diode / on / off beep 10. Manual / automatic range 11. Max / Min / Relative 12. Current gear protection: equipped with fused fuse 440mA / 11A 1000V fuse 13. Dangerous voltage warning function, easier to use 14. CAT III1000V / CAT IV600V safety level double insulation design.
Product overview Pipe type ultrasonic flowmeter is composed of a main body and a pipe segment type sensor. The DN15-DN32 uses a -type pipe segment sensor, and the DN40 and above uses a standard pipe segment sensor. The pipe-type ultrasonic flowmeter has the advantages of simple installation, low starting flow, high measurement accuracy, and no pressure loss. The main unit can be installed in the wall, instrument box, and distribution box with a protection level of IP67. The external clip sensor is installed on the surface of the pipe and selects different sensors. The applicable diameter is DN15~DN6000mm. Product features 1. Simple installation, no need for professional workers 2. High precision and low price 3. Can work in humid and water-immersed environment
GMF200 Series Ultrasonic Flowmeter Model GMF200-D Principle Ultrasonic time difference principle Precision ±1% Display 4x8 Chinese or 4x16 Western dot matrix backlit LCD, supporting Chinese, English, Italian and French languages Output 1 channel OCT pulse output (pulse width 6-1000ms, default 200ms) Data interface Isolating the RS-232 application interface, the flow meter can be upgraded through a PC Pipe Steel, stainless steel, cast iron, copper, PVC, aluminum, fiberglass, and other dense pipes, allowing lining Pipe inner diameter 15-6000mm Straight pipe The sensor installation point is best to meet: upstream 10D, downstream 5D, from the pump outlet 30D (D is the pipe diameter) Medium Water, sea water, sewage, acid and alkali, alcohol, beer, various oils, etc. Fluid temperature -30~+160�°C Turbidity 1000pmm bubble content is small Flow rate 0±10m/s Working environment Host: -20 ~ +60 C; flow sensor: -30 ~ +160 C Host: 85% RH; sensor protection grade: IP67 Power supply 3-cell rechargeable Ni-MH battery with 1.2V capacity of 2000mAH, which can work continuously for more than 12 hours every time. Power consumption 1W Housing material Flame retardant ABS Host weight 390g
GMF200-H series hand-held ultrasonic flowmeter realizes non-contact measurement of liquid flow. Install the sensor on the outer wall of the pipe to complete the flow measurement. With small size, easy to carry, accurate measurement and so on. Widely used in tap water, heating, water conservancy, metallurgy, chemical, machinery, energy and other industries. It can be used for production monitoring, flow calibration, temporary detection, flow inspection, water meter balance debugging, heating network balance debugging, and energy saving monitoring. It is a necessary tool for timely flow detection.
Product Description ADL10-E Single Phase Electric Energy Meter General ADL rail- installation Electricity meters is a new generation electricity meter developed by Acrel Co,.Ltd, resulting from many years experience in designing Electricity meters. LCD display and electricity pulse output function is installed in the power meter; clock, rate period parameters can be set also. Data swap with the super ordination machine via RS485 communication interface greatly facilitate the power automated administration. This power meter has advantages of smaller volume, high precision, good EMC, easy installation etc, meet the related technical requirements of electronic power meter in the IEC62053-21,IEC 62053-22 standard. Technical Parameters Voltage Reference voltage AC 220V Reference frequency 45-65 Hz Consumption
Product Description ADL10-E Single Phase Electric Energy Meter General ADL rail- installation Electricity meters is a new generation electricity meter developed by Acrel Co,.Ltd, resulting from many years experience in designing Electricity meters. LCD display and electricity pulse output function is installed in the power meter; clock, rate period parameters can be set also. Data swap with the super ordination machine via RS485 communication interface greatly facilitate the power automated administration. This power meter has advantages of smaller volume, high precision, good EMC, easy installation etc, meet the related technical requirements of electronic power meter in the IEC62053-21,IEC 62053-22 standard. Technical Parameters Voltage Reference voltage AC 220V Reference frequency 45-65 Hz Consumption
Product Description ADL10-E Single Phase Electric Energy Meter General ADL rail- installation Electricity meters is a new generation electricity meter developed by Acrel Co,.Ltd, resulting from many years experience in designing Electricity meters. LCD display and electricity pulse output function is installed in the power meter; clock, rate period parameters can be set also. Data swap with the super ordination machine via RS485 communication interface greatly facilitate the power automated administration. This power meter has advantages of smaller volume, high precision, good EMC, easy installation etc, meet the related technical requirements of electronic power meter in the IEC62053-21,IEC 62053-22 standard. Technical Parameters Voltage Reference voltage AC 220V Reference frequency 45-65 Hz Consumption
Product Description ADL10-E Single Phase Electric Energy Meter General ADL rail- installation Electricity meters is a new generation electricity meter developed by Acrel Co,.Ltd, resulting from many years experience in designing Electricity meters. LCD display and electricity pulse output function is installed in the power meter; clock, rate period parameters can be set also. Data swap with the super ordination machine via RS485 communication interface greatly facilitate the power automated administration. This power meter has advantages of smaller volume, high precision, good EMC, easy installation etc, meet the related technical requirements of electronic power meter in the IEC62053-21,IEC 62053-22 standard. Technical Parameters Voltage Reference voltage AC 220V Reference frequency 45-65 Hz Consumption
Product Description ADL10-E Single Phase Electric Energy Meter General ADL rail- installation Electricity meters is a new generation electricity meter developed by Acrel Co,.Ltd, resulting from many years experience in designing Electricity meters. LCD display and electricity pulse output function is installed in the power meter; clock, rate period parameters can be set also. Data swap with the super ordination machine via RS485 communication interface greatly facilitate the power automated administration. This power meter has advantages of smaller volume, high precision, good EMC, easy installation etc, meet the related technical requirements of electronic power meter in the IEC62053-21,IEC 62053-22 standard. Technical Parameters Voltage Reference voltage AC 220V Reference frequency 45-65 Hz Consumption
Product Description ADL10-E Single Phase Electric Energy Meter General ADL rail- installation Electricity meters is a new generation electricity meter developed by Acrel Co,.Ltd, resulting from many years experience in designing Electricity meters. LCD display and electricity pulse output function is installed in the power meter; clock, rate period parameters can be set also. Data swap with the super ordination machine via RS485 communication interface greatly facilitate the power automated administration. This power meter has advantages of smaller volume, high precision, good EMC, easy installation etc, meet the related technical requirements of electronic power meter in the IEC62053-21,IEC 62053-22 standard. Technical Parameters Voltage Reference voltage AC 220V Reference frequency 45-65 Hz Consumption
