Forged super alloy steel-Quenched Tempered.
Individually proof test at 2.5 times Working Load Limit.
Fatigue tested at 1.5 times Working Load Limit for 20000 cycles.
Breakage test magnaflux crack detection.
With spring inside for better pivoting control.
Appropriate tie down instruction are available upon request.
All dimensions in mm
Proof Load = 2 x S.W.L. (Safe Working Load)
Other threads can also be supplied to special order.
Shoulder Nut Eye Bolt - Installation for Angular loading
The threaded shank must protrude through the load sufficiently to allow full engagement of the nut.
If the eye bolt protrudes so far through the load that the nut cannot be tightened securely against the load, use properly sized washers to take up the extra space
Between The Nut And The Load
Place washers or spacers between nut and load so that when the nut is tightened securely, the shoulder is secured flush against the load surface.
Forged Eye Bolt Warning & Applications
Important Safety Information - Read & Follow
Inspection / Maintenance Safety
Never use eye bolt that shows signs of wear or damage
Never use eye bolt if eye or shank is bent or elongated.
Always be sure threads on shank and receiving holes are clean
Never machine, grind, or cut eye bolt.
Assembly Safety
Never exceed load limits specified in Table I
Never use regular nut eye bolts for angular lifts.
Always use shoulder nut eye bolts (or machinery eye bolts) for angular lifts.
For angular lifts, adjust working load as follows:
Never undercut an eye bolt to seat shoulder against the load.
Always countersink receiving hole or use washers to seat shoulder.
Always screw eye bolt down completely for proper seating.
Always tighten nuts securely against the load.
Shoulder Nut Eye Bolt - Installation for Angular loading
Operating Safety
Always stand clear of load
Never lift load with steady, even pull - do not jerk.
Always apply load to eye bolt in the plane of the eye, not at an angle
Never exceed the capacity of the eye bolt.
When using lifting slings of two or more legs, make sure the loads in the legs are calculated using the angle from the vertical to the leg and properly size the shoulder nut or machinery eye bolt for the angular load.
Key Specification-
1.Grade 4.6,8.8,10.9 & b7 gr 36/55/105
2.Material as per is-1397 part iii astm a193 astm f1554
3.Size m6 to m100 & above (1/4'' to 4.0'' & above)
Key advantage
1.Highly accurate in dimension and supply with certificate
Key Specification-
1.Grade 4.6,5.6,6.8,8.8,10.9,12.9 & b7,b16,307b,b8,b8m
2.Material as per is i 367 part-iii sae j429,is-3757 & astm 193,a307,a453
3.Size m6 to m100 & above (1/4'' to 4.0'' & above)
Key Advantage
1.Highly accurate in dimension and supply with certificate
Our main products include, Liner Bolts, LN Cap Bolts, Hex Bolts, Nib Bolts, Square Head Bolts, Shear Head Bolts, Full/Half threaded studs Hex Nuts, Key Nuts etc as per the special specifications of the clients and under third party inspection of their choice. We manufacture studs, bolts, screws as per SA193 GrB7, B7M, B16, B6X, B6, B8, B8M , SA320 L7 & nuts as per SA194 Gr. 2H, 2HM, Gr. 7, Gr. 7M, Gr. 6, Gr. 8, Gr. 8M etc.
Our main products include, Liner Bolts, LN Cap Bolts, Hex Bolts, Nib Bolts, Square Head Bolts, Shear Head Bolts, Full/Half threaded studs Hex Nuts, Key Nuts etc as per the special specifications of the clients and under third party inspection of their choice. We manufacture studs, bolts, screws as per SA193 GrB7, B7M, B16, B6X, B6, B8, B8M , SA320 L7 & nuts as per SA194 Gr. 2H, 2HM, Gr. 7, Gr. 7M, Gr. 6, Gr. 8, Gr. 8M etc.
Our main products include, Liner Bolts, LN Cap Bolts, Hex Bolts, Nib Bolts, Square Head Bolts, Shear Head Bolts, Full/Half threaded studs Hex Nuts, Key Nuts etc as per the special specifications of the clients and under third party inspection of their choice. We manufacture studs, bolts, screws as per SA193 GrB7, B7M, B16, B6X, B6, B8, B8M , SA320 L7 & nuts as per SA194 Gr. 2H, 2HM, Gr. 7, Gr. 7M, Gr. 6, Gr. 8, Gr. 8M etc.
Our main products include, Liner Bolts, LN Cap Bolts, Hex Bolts, Nib Bolts, Square Head Bolts, Shear Head Bolts, Full/Half threaded studs Hex Nuts, Key Nuts etc as per the special specifications of the clients and under third party inspection of their choice. We manufacture studs, bolts, screws as per SA193 GrB7, B7M, B16, B6X, B6, B8, B8M , SA320 L7 & nuts as per SA194 Gr. 2H, 2HM, Gr. 7, Gr. 7M, Gr. 6, Gr. 8, Gr. 8M etc.
