Basic specification of stainless steel water tank: Material: Stainless steel SUS304 or SUS316 Water Tank Volume: 1-1000CBM Stainless Steel Panel Size: 1.0m*1.0m, 1.0m*0.5m,0.5*0.5m Stainless Steel Panel Thickness: Wall board thickness: 4mm,6mm,7.5mm,8mm,10mm and etc. Accessory:Water inlet and outlet,Bolts,Steeling tapes,Draw rod,Flange connection,Ladder,Base channel(C channel)etc. Water Tank size: can be produced according to customer's size
Description Two component, air drying, high solids, Epoxy coating. The product has the advantage of epoxy resin composition with speciality pigment, which facilitates one-coat, high build application for high performance. The product can be applied on minimum prepared surface and is designed to completely wet the substrate. Excellent adhesion is obtained on a variety of intact surfaces including over old coating and tightly adherent rust. The composition has been balanced to a convenient mixing ratio by volume with excellent application characteristics. The ZERO solvent content reduces the problem of lifting of the paint film and adhesion failure by blistering and pin holing. This assures a stable long term performance. Recommended Use :- It is mainly recommended in those areas where blasting is impractical or impossible. Uses include steel structures in Industrial plants, bridges, tank exteriors, oil tanks, pipes, marine atmosphere, cooling towers, etc. It has good resistance to spillage and fumes of acids, alkalis, fresh and salt water. Recommended as a primer on suitably cleaned mild steel surface in various Fertilizer units, Refineries, Chemical and other plants, Transportation industries, steel plants, cement plants, power plants, pulp and paper industries, pharmaceutical industries, water tank, pipelines etc. for application on tank exteriors and interiors, structural steel, pipelines, machineries, vessels, etc. Physical Data COLOUR : Selected industrial shades FINISH : Semi glossy SOLIDS BY VOLUME : 80 �± 2% THEORETICAL SPREADING RATE : 10 sq.mt. / ltr. at a recommended DFT of 80 �µ FLASH POINT : Base : Above 25�°C Hardener : Above 25�°C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30�°C) : SURFACE DRY : 4 hours FULL CURE : 7 days HARD DRY : Overnight SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO Base : Hardener ( As per our recommendations) : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Airless Spray POT LIFE : 2 - 3 hours min at 30�° C RECOMMENDED DFT : 75-100 mic. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU
Product Name:Purified water storage tank Deionized and Ultra-pure Water Storage Tanks What are some common materials used to make purified water tanks? Purified water tanks can be made from a variety of materials, depending on the intended use and application. Some common materials used to make purified water tanks include: Stainless steel: Stainless steel is a durable and corrosion-resistant material that is commonly used in the food and beverage industry. It is easy to clean and maintain and can withstand high temperatures and pressures.
TOPTION FRP plant produces various horizontal and vertical FRP storage tanks, FRP containers, and FRP large-scale series of FRP pressure vessels. Different types of high-quality resins are selected according to the medium stored by the user, which consists of a high-resin content corrosion-resistant liner, a leakproof layer, a fiber-wound strengthening layer, and an outer protective layer. The product's working temperature is between -50 and 80, and the pressure resistance is generally below 6.4MPa. It has the advantages of pressure resistance, corrosion resistance, aging resistance, and long service life. Additionally, FRP has the characteristics of lightweight, high strength, leak prevention, insulation, non-toxicity, and smooth surface. Fiberglass products can be widely used in the petroleum, chemical, textile, printing and dyeing, power, transportation, food and beverage brewing, biological and pharmaceutical industries, as well as in water supply and drainage, seawater desalination, water conservancy and irrigation, and national defense engineering.
Product Description Faber cylinders give you the quality and performance you expect and appreciate in a steel scuba cylinder. With one of the widest ranges of sizes in the market today Faber cylinders offer you the needed volume and flexibility to maximize your bottom time. With over 35 years of cylinder manufacturing experience, let Faber make your diving experience a safe and enjoyable one. From the highest quality, deep drawn Chromium Molybdenum steel, to our exclusive Phosphatized-cleaned internal surface, triple protected zinc, and epoxy and polyurethane finish for durability, you get the best from Faber. High Pressure tanks that are compatible with any regulator Free Visual Inspection Program (VIP) Included Includes Pro Valve-Standard Yoke and DIN Compatible 3442 PSI Nitrox Compatible to 40% (The Recreational Limits of Nitrox) Durable corrosion resistant finish Chromium Molybdenum Steel DIAMETER: 5.5 inches LENGTH: 17.7 inches WEIGHT EMPTY: 14.8 lbs. BUOYANCY FULL: -1.48 lbs. BUOYANCY EMPTY: -4.51 lbs. FULL MANUFACTURER'S WARRANTY
Product Description Blue Steel Faber HP Steel Tank Painted Silver with Pro Valve Includes: Blue Steel PRO Valve, Tank, Current Hydro, VIP and Tank boot Faber Steel Cylinders Feature: 3442 psi (237 bar) working pressure Phosphatized-cleaned interior DOT SP13488 and TC SU7694-237 O2 cleaned for use with up to 40% pre-blended nitrox Includes rubber self-draining tank boot with round rim Inlet thread is standard �¾â??-14 NPSM Painted Silver Triple protected the finish for long-lasting durability. The process includes a zinc galvanization spray followed by epoxy paint and then a polyurethane topcoat.
Product Description Blue Steel Faber HP Steel Tank Hot Dip Galvanized with Pro Valve Includes: Blue Steel PRO Valve, Tank, Current Hydro, VIP and Tank boot Faber Steel Cylinders Feature: 3442 psi (237 bar) working pressure Phosphatized-cleaned interior DOT SP13488 and TC SU7694-237 O2 cleaned for use with up to 40% pre-blended nitrox Includes rubber self-draining tank boot with round rim Inlet thread is standard �¾â??-14 NPSM Hot Dip Galvanized The most durable, corrosion-free exterior finish possible. The process involves submerging the cylinder into molten zinc. The zinc metallurgically bonds to the steel.
Dosing Tank Capacity: 100 LIT. MOC:LLDPE.
Jotun polishing machine/ China stainless steel tank/cylinder shell surface automatic polishing machine This is JT-1 tank shell surface polishing machine,which can polish tank shell inside and outside surface. Producting workpiece Material:Metal(stainless steel,carbon sheel,etc.) Min and max diameter:200-5000mm, Min and max thickness:>1mm Min and max length:300-6000mm. Weight:1/2/3/5/10Tons. Surface roughness:Ra 0.25m Shipment port:Shanghai port. Delivery time:30 working days Payment: T/T, L/C Warranty: 12months.
FRP tank product according customer's requirement
Pressure tanks are used in closed water circulation systems to balance water flow and pressure, avoiding frequent opening of safety valves and frequent replenishment of automatic water valves. The expansion tank not only serves to accommodate the expansion water, but also serves as a makeup water tank. The expansion tank is filled with air and can obtain a larger volume to accommodate the expansion water. High and low pressure expansion tanks can use their own pressure to supplement water to the pressure stabilization system in parallel. The control of each point of this device is interlocking reaction, automatic operation, small pressure fluctuation range, safe and reliable, energy-saving, and good economic effect.
Supply Ability & Additional Information Packaging: Wooden packaging or as requirementsTransportation: Ocean,Land,AirPlace of Origin: ChinaPayment Type: L/C,T/T,OthersIncoterm: FOB,CFR,CIF,EXW Packaging & Delivery Selling Units: Set/Sets Package Type: Wooden packaging or as requirements 50CBM 0.8Mpa low temperature LNG Storage Tankï¼? 1. Effective Volume: 50.0 m3 2. Working pressure: 0.8 MPa 3. Overall dimension: 3016*12120mm 4. Shell material: Outer jacket: Q245-R; Inner: S30408. 5. Insulation: Vacuum powder insulation 6. Tare weight: About 17680KG
Equipment Name: Conveying tank Manufacture Code: GB150Specification: ID1200Design pressure: 1.0 MPa Material: Q345R Volume: 1.5 m
Asme air storage tank with u stamp project name: petroequipment name: low pressure air storage tankmanufacture code: asmedesign pressure: 1.1 mpa, design temperature: 110 specification: id1000material: sa-516m gr.485volume: 2ma
Material: 6065A Volume: 40L Length: 720 mm Diameter: 280 mm Thickness: 3 mm Weight: 6 KG Max pressure: 5.5 MPA We can produce almost all the parts with aluminium alloy, because we are the second largest aluminium extrusion product developer and the largest in Asia. Just need a product profile drawings, after that I can calculate price for you.
The corrosive gas include the ethane, methane, butane, propane and natural gas. Cause the medium is the corrosive gas, we promise that the every tank must be X-ray detect before to the customer. We provide the gas storage tank with ASME code and Chinese GB to choice. As design we can provide areasonable price for the customer.
Application of the mirror surface aluminum fuel tank trailer The mirror surface aluminum fuel tank trailer is to transport the fuel from the fuel refinery factory to different fuel stations. The aluminum tank is made of aluminum alloy 5454 which has a better performance of heat resistance. This kind of aluminum tank trailer is especially suitable in heat and dusty area. Advantages of the mirror surface aluminum fuel tank trailer The advantages of aluminum fuel tank trailer are less weight, more load, lower operation cost, good appearance, etc. Except the good performance of heat resistance, mirror surface also appears good image which is also very attractive for transporters. The surface of aluminium fuel tank could keeps shinny and beautiful long time, no need painting and easy to wash. This also could improve the company image. Description of the mirror surface aluminum fuel tank trailer The 3 axle mirror surface aluminum fuel tank trailer is equipped with whole set of YORK axle and suspension, JOST landing gear and kingpin, Double coin super single tyre and aluminum wheel rim. The tank parts using OPW CIVOCAN parts. All these superior quality China parts and world famous parts support our good quality aluminum fuel trailer. What's more, this trailer is checked carefully both by inspector and machines to make sure this isn't any defective on welding and function. SpecificationDimensionOverall dimension11800x2500x2980mmTare weight7500kgsTankShapeRo und shapeTotal volume42000LTank body materialAluminum alloy 5454 5mm mirror surfaceTank end plateAluminum alloy 5454 7mm mirror surfaceCompartment2 independent compartmentsManhole coverAluminum manhole cover, OPW brandBottom valvePneumatic control bottom valve, OPW brandDischarge valve4 inches European type discharge valve, OPW brandVapor recovery systemWith vapor recovery system, OPW brandTrailer chassisMain beamHeavy duty special design I beam Made by aluminum alloy 6061AxleYORK axle, 13T capacityLanding gearJOST landing gearKingpinJOST kingpin 2 inchesSuspensionA whole set of YORK Air suspensionBraking systemWABCO RE 6 replay valve, T30/30 air chamberTireTubeless tyre 12R22.5Wheel rimAluminum wheel rim 9.0R22.5AccessoriesOne tool box, 2pcs extinguisher, foldable handrill
Quick DetailsPlace of Origin:Zhejiang,China (Mainland)Brand Name:OEMModel Number:PT-10HType:High Pressure GunApplication:Paint Spray GunCup Volume:10L/Qt, 2.65 Gal.Max working pressure:43.5 psi (3 bar)Air hose connection:1/4" NPTLiquid hose connection:3/8" NPTPaint tank/pot:10L/Qt manual/hand mixing air pressure quality paint/pot tank PT-10HPackaging & DeliveryPackaging Details:Sea worthy cartonDelivery Time: Shipped in 7 days after paymentProduct DescriptionProduct ApplicationBig capacity tank perfect for big area spraying such as wall, floor, assembly line, garages, body shop, ship yard etc.10L/Qt, 2.65 Gal. manual/hand stir HVLP air pressure quality paint pot PT-10HMax Operating Pressure43.5 psi (3 bar)Paint Capacity10 Liter/Qt,2.65 Gal.Air hose connection1/4"Liquid hose connection3/8"Stir typemanual/handInner tankS.S inner tankMain Features1)� Complete with paint tank(10 lier)/qt,2.65 Gal., manual stirring pole, paint exit tube, air pressure gauge, air regulator, safety valve, pressure release valve, fluid outlet valve(2pcs), air inelt&outlet, S.S inner tank air hose, paint hose(avaiable with longer ones) and 4 castors.2) Actuated by manual/hand3) One -piece format seamless steel body4) S.S inner is easy to replace the paint5) Large lid clasp&gasket makes good sealing and stability during operating6) Air safety valve and pressure regulator. for safety7) Mounted on castors for easy manoeuvrability8) Carry hook, paint strirrer and assembly spanner includedDetailed ImagesOur ServicePacking & Delivery
Feed water tanks
We are manufacturer for Liquid Nitrogen containers ranging from 0.5 Ltr till 35 Ltrs, even can make as per your requirements. We are supplying in India to various limited companies. We can also supply Epoxy Insulation Tubes. Kindly send me your detailed requirements so that we can quote you the best rates FOB / CIF.
