Slag crushing process.
Jaw Crusher Components: 1 Frame 2 Crushing Chamber 3 Swing Jaw & Main Bearing Housings 4 Flywheel 5 Eccentric Shaft 6 Bearings 7 Hydraulic Cylinder 8 Shim 9 Toggle Block 10 Tension Rod with spring 11 Toggle Seat 12 Toggle Plates 13 Check Plates 14 fixed plates (left) moveable plate (right) Illustration of How Jaw Crusher Crushes: A jaw crusher reduces large size rocks or ore by placing the rock into compression, a fixed jaw, mounted in a ¡°V¡± alignment is the stationary breaking surface, while the moveable jaw plate exerts force on the rock by forcing it against the fixed jaw plate. The space at bottom of the ¡°V¡±, aligned jaw plate is the crusher product size gap, or the size of the crushed product from the jaw crusher. Model PEF150X750 PEF200X300 PEF250X400 PEF400X600 PEF350X750 PEF500X750 PEF600X900 PEF750X1060 PEF900X1200 PEF1000X1200 PEF1200X1500 PEX150X750 PEX250X750 PEX250X1200 PEX300X1300 International standard container, the spare parts is packed in wooden cases.
High efficiency Jaw Crusher Overview of Jaw crusher Jaw Crusher is typically used as primary crushers, or the first step in the process of reducing rock. They typically crush using compression. The rock is dropped between two rigid pieces of metal, one of which then move inwards towards the rock, and the rock is crushed because it has a lower breaking point than the opposing metal piece. Jaw crusher movement is obtained by using a pivot point located at one end of the "swing jaw", and an eccentric motion located at the opposite end. Working Principle of of Jaw crusher The motor transmits power through belt, drives the moving jaw to do periodic motion towards the fixed jaw by the eccentric shaft. The angle between toggle plate and moving jaw plate increases when moving jaw moves. So the moving jaw moves towards the fixed jaw. The stuff will be crushed in this process. The angle between toggle plate and moving jaw decreases when moving jaw moves down, the moving jaw leaves fixed jaw by pulling rod and spring, the final crushed stuff will be discharged from the outlet. Features of Jaw crusher 1.Deep Crushing cavity£¬improve the feeding capacity and output. 2.High ratio of crushing, Even final size, 3.The adjusting devices of discharging opening is reliable,convenient, and has wide adjustment, increases the flexibility; 4.Easy maintenance, 5.Simple structure, 6.Reliable working condition, 7.energy saving 8.satisfy different requirements 9.Low noise, little dustGrand Cempaka Jakarta. International standard container, the spare parts is packed in wooden cases.
PFW series impact crusher improves the adjusting device, the operation becomes more convenient. The tri ¨C cavity makes excellent capability in the fine crushing and super fine crushing line. The bi-cavity can simplify the process flow in the coarse crushing line. Benefits: 1. Bearing adopts the integrated cast-steel structure, which ensures the perfect match with crusher frame. Meanwhile, it greatly increases the radial intensity of bearing seat. 2. Unique fixing device of blow bar brings higher reliability. 3. Reformative adjusting device decrease the time of machine stop and overhaul. 4. Self-own open-top device can quickly finish the replacement of wearing parts. 5. Larger bearing specification and higher carrying capacity. 6. Rotor analysis ensures stableness and reliability.
Shanghai Shibang Machinery Co., Ltd, one of the most famous rock and mineral processing company in the world, is launching a new comprehensive portable plant for efficient fully mobile crushing. YG938E69 portable crushing plant concept is fully adaptable to all mobile crushing needs, it set up a new range of business opportunities for contractors, quarry operators, recycling and mining applications. It can eliminate the obstacles of the crushing places and circumstances, and offer the high efficient and low cost project plants for the client. To the client, it is the best choice. YG938E69 portable crushing plant highlights: 1. PE Series high performance jaw crushers. 2. Incorporated the feeder and vibrating screen into the crusher. 3. Everything on board: crusher, feeders, screens, belts and power installations. 4. Quick road transportation thanks to king pin arrangement. 5. Installation support legs on the track quick to set-up. 6. Electric motor and control cabinet are on the same truck.
SBM is a world-leading company in the field of making rock and mineral processing machine, which has equipped tens and thousands of crushers around the world since the late 20th century. Nowadays, the PEW jaw crusher in European style undoubtedly becomes the most welcome products in the world. When you want to crush the hard materials in high efficiency, the best choice for you is the PEW series of jaw crushers in European style, which adopts the most advanced international crushing technology as well as the world-class skills in making.
VSI5X series vertical shaft crushers adopt Germanic advanced technique and obtain many proprietary intellectual property rights and the patent technology as well as integrate with three types of crushing who have been the core equipments in sand making industry. The new type of high-efficiency crushers obtains the following advantages: 1, Optimized deep-cavity rotor improve the material throughput by about 30%. 2, Part-worn around protecting plate can be reversed end for end to use again which improve the operating factor by more than 48%. 3, Assembled hammer reduces the cost by more than 30%. In addition, adding the assistant hammer which protects the frame when the main hammer is worn. 4, The core wear resistant material adopts the American high-standard wear resistant material. 5, Adopting the lozenge impact plate protects the frame better.
SBM-Vertical shaft impact.: SBM VSI crusher is designed by reputed German expert of Shibang and every index of SBM VSI crusher is in world's leading standard. SBM VSI crusher incorporates three crushing types and it can be operated 720 hours continuously. Nowadays, SBM VSI crusher has replaced hammer crusher, roller crusher, roller ball mill, etc. and become the mainstream equipment in sand making business. Technological advantages: SBM VSI crusher incorporates three crushing styles its feeding style incorporates material on material, materials on iron and falling at sides. Customers can adjust the machines according to their own demand. SBM VSI crusher realizes multiple functions in one machine, which is a big breakthrough in sand making field. Excellent performance and long service time: 1.Special light oil lubrication systems ensures the temperature to be within 25f? 2.Brand new automatic protection device provides the machine with vibrating, oil filtering and warning system 3.New type oil filting system ensures the bearings and other transmission system are not abraded and peolong their service time 4.Choice wearable materials prolong the service time of the machine by 40%. So the cost is lowered by more than 40%. Model: VSI7611 VSI8518 VSI9526 VSI1140. Model:VSI 7611 Capacity (t/h): Feed both at center and at sides:120-180 Feed at center:60-90 Max feed size (mm): soft material ?35 hard material?30 Rotation speed (r/min): 1700-1890 Power (kw) : 110-150 Overall dimension L*W*H (mm) : 3700*2150*2100 Weight (t) : 7.8. Model: VSI8518 Capacity (t/h): Feed both at center and at sides: 200-260 Feed at center: 100-130 Max feed size (mm): soft material?40 hard material?35 Rotation speed (r/min): 1520-1690 Power (kw) : 180-220 Overall dimension L*W*H (mm) : 4140*2280*2425 Weight (t) : 10.3. Model: 9526 Capacity (t/h): Feed both at center and at sides: 300-380 Feed at center:150-190 Max feed size (mm): soft material?45 hard material?40 Rotation speed (r/min): 1360-1510 Power (kw) : 264-320 Overall dimension L*W*H (mm) : 4560*2447*2778 Weight (t) :16. Model:VSI1140 Capacity (t/h): Feed both at center and at sides:450-520 Feed at center: 225-260 Max feed size (mm): soft material?50 hard material?45 Rotation speed (r/min): 1180-1310 Power (kw) : 400-440 Overall dimension L*W*H (mm) : 5000*2700*3300 Weight (t) :25.6.
HPC series cone crusher with high-efficiency and hydraulic pressure was widely used in mining, concrete factory, sandstone making, etc. The machinery's pressure resistance strength is under 350Mpa. And they are widely suitable for primary crushing of many kinds of mining and rock such as many kinds of ores, concrete, fireproof material, bauxite, quartzite, corundum, perlite, ironstone, basalt, etc. Features and Benefits 1.The new series of HPC cone crusher with high-efficiency and hydraulic pressure equipment is adopted three protecting equipment such as protecting oilcan, locking oilcan and hydraulic driving oilcan. They not only protect the machinery, but could deal with troubles without disassembly the parts. 2.The equipment also can adjust the size of final material. The machinery with high dependability operated very expediently. 3. The crushing chamber specially designed according to particles sink principal and its matching speed can sharply increase the crushing ratio, output and content percentage of cubical product in final crushed material. 4. In the special circumstances such as irons was feed into the crushing chamber together with the materials and there is a jam in the crushing chamber, the hydraulic equipment could open the cover automatically, then the products could output successfully. It greatly reduced the trouble of stopping the machine to output the products artificially. Which makes the maintenance more convenient and with low cost. 5.It is adjusted by hydraulic device and lubricated by the dilute oil. And with locking sleeve assembly, it can overcome the trouble of oil and water being mixed together. 6.The concave and mantle made by high manganese steel. Owing to the change of the concavef+s style and the protect of the crushed products, The abrasion of the machine is reduced greatly and can last long compared with the old cone crusher.
Shibang series of jaw crusher can reach the crushing ratio of 4-6 and the shape of final product is even. Jaw crushers are widely applied to crush high hardness, mid hardness and soft rocks and ores such as slag, construction materials, marble, etc. The pressure resistance strength is under 200mpa, that is, suitable for primary crush. Jaw crushers can be used in mining, metallurgical industry, construction, road and railway building, water conservancy, chemistry, etc.
HCS Series cone crusher features Comparing with other kinds crusher, HCS Series Symons cone crusher have excellences for fine crushing, high productions and low maintenance. The long force arm designed into the HCS Series Symons cone provides greater crushing force. And the spring release system generates more opposing force than other cone crushers. So use in mine industry widely.
The impact crusher which is a kind Rock crusher that employs self-weigh security device in its back frame. When other objects enter the impact cavity, they will be forced out of the machine by the impact rack in the front and back of the machine. Features and Benefits of our impact crusher: 1.Our impact crusher is of High reduction ratio and crushing efficiency 2. No-board connection; The blow bar of our impact crusher with high chrome(high chromed blow bar). 3. Impact plate with a special shape. 4. Crushed product of impact crusher with cubical shape. 5. Easy maintenance and reliable operation. Type:PF-1010,PF-1210,PF-1214,PF-1315£¬PFV-1010£¬PFV-1210,PFV-1214,PFV-1315 Spec.: ¦1000*1050,¦1250*1050,¦1250*1400,¦1300¡Á1500,¦1000¡Á1050,¦1250¡Á1050,¦1250¡Á1400,¦1320¡Á1500 Feeder Opening (mm):350,350,350,350,350,350,350,350 Crushing Capacity (t/h):,50-80,70-120,80-160,160-260,50-80,70-120,130-180,150-220 Motor Power (KW): 55-75,110-132,132-160,180-260,55-75,110-132,132-160,180-220 Weight (t):12.6,14,18.6,24.2,13.2,15.2,18.6,24.5.
Symons cone crusher is a kind of crusher, stone crusher, rock crusher, crushing machine, crushing plant, rock crusher models which is also called gyratory crusher. Features of Symons Cone Crusher : Comparing with other kinds crusher, Symons cone crusher have excellences for fine crushing, high productions and low maintenance. The long force arm designed into the Symons cone provides greater crushing force. And the spring release system generates more opposing force than other cone crushers. So use in mine industry widely. Standard Symons Cone Crusher Technique paramete Type:CSB75,CSB110,CSB160,CSB240,CSB315, Dia. of cone mm (inch): 900 (3'),1200 (4'),1295 (4 1/4'),1650 (5 1/2'),2134 (7') Countershaf (r/min):580,485,485,485,435. Power (kw):75,110,160,240,315. Weight (ton): 15,20,27,55,110. Overall dimension (mm):2821x1880x2164,2821*1974*2651,2800x 2342x2668,3911x2870x3771,4613x3251x4732.
Energy-saving ball mill Energy-saving ball mill changes the intrinsic grinding machine structure. Its body and ground plank are integrated to one unit. So when fixed, it can be lowered on to a basal plane for one time. The use of aligning spherical roller bearing with centripetal spherical support of the main bearing can reduce energy consumption by 30%.The trellis-pattern forced discharging is substituted by the down-flow type controlling so that the milled granularity and the capacity can be increased by 15-20%.
Characteristics ----A wide selection range of materials with the Mohs scale of hardness below 6; ----Higher degree of fineness by the high pressure spring. ----Low in energy consumption compared with Jet Mill ----Less investment with accelerated cost recovery ----Independent system ----Less pollution; dust extraction fully conforms to national standard. ----Good sealing effect of grinding rollers. ----Technical specifications: Main Technical Data Model YGM7826 YGM8327 YGM9531 YGM3220 Roller Number 3 3 4 3 4 Roller Diameter(mm) ¦µ260 ¦µ270 ¦µ310 ¦µ320 ¦µ320 Ring Inside Dia.(mm) ¦µ780 ¦µ830 ¦µ950 ¦µ970 ¦µ970 Rotational Speed (r/min) 160 140 130 148 130 Max Feeding Size (mm) ¡´20 ¡´20 ¡´25 20-25 20-25 Output (kg/h) 25-500 30-680 150-1000 2000-5800 3000-6000 Motor Type of Main Engine Y225-8-18.5 Y225M-8-22 Y225S-4-37 Y225S-4-45 Motor Type of Air blower Y160L-4-15 Y180M-4-18.5 Y200L-4-30 Y200L-4-37 Motor Type of Size Analyzer Y160M-6-7.5 Y160M-6-7.5 Y160M-6-7.5 YCT200-4A-11 Gross Power (kw) 41 48 74.5 93 Overall Dimension(L*W*H)(m) 4.5*4.2*5.1 5.3*4.1*5.2 7.1*5.9*7.9 7.1*5.9*7.9 Weight (t) 4.8 6 11.5 13 14 Output Size (mesh) 500mesh(0.025mm)-1250mesh(0.01mm),some can be 2500 mesh(0.005mm) 20 mesh -425 mesh£¬ some can be 1000mesh.
Used for crushing of stone, iron ore, coal etc.
Crushing plants and crushers for stone, iron ore, dolomite, limestone, coal crushers etc.
Jaw crusher.
Dehong jaw crusher series are based on years experience and technology development. The continuous improvement and refinement has made them the preferred jaw crusher for professionals and our customers. They can meet most crushing requirements in primary and secondary crushing, and the largest compression resistance of the material is 320mpa. This series are widely used in stone mining, metallurgical, construction, smelting, hydraulic and chemical industries, etc.
Ball mill is mainly composed of charging and discharging, cyclone and rotation parts (like redactor, minor rotation gear, motor, electric machine, etc). Hollow axis is made of steel parts with a lining replacable. Major rotation gear, machined by rolling wheel of casting, is lined with wearing plate with fine wear-resisting property. This machine runs stably and reliably. the ball mill technical specifications from Dia 900-Dia 3200mm. Export standard container, or in bulk carrier.
