Here please allow me to share some information with you about our products:
1. Usage. Our products are widely used in the bathroom, pool and spa area, driveways, balcony, multi-residential, courtyard/patio and so on.
2. Quality. Our product have got WaterMark certification, material SS304 or SS316 all available for us
3. Type. Smooth linear grate, anti-slip grate, different wire grate, lock in the center of grate, with four side bar, and we can also custom-make some other type you needed.
4. Surface. We adopt the new flat welded technology, which can assure the grate surface is very straight and smooth.
5. Export: We have abundant experience in export to Australia, suggestions will be offered about the product that popular in your country
6. Service. We have superior pre-sales and after-sales service and we also can provide sample according to your request for your further testing.
The mixer component pictured here is made of stainless steel. The entire component with od 1950mm and 2205mm long after fabrication shall be finished by machining center for perfect dimensional precision.
Product 4" X 10' Long, 100% Stainless Steel Wool
Material
Stainless steel and poly fiber
Weight Ranging from 2000gsm
Size 4"*10m per roll or as requested
Width
47"/48"
Package Roll or Sheet
B):Feature:
1. 100% non-toxic and environmentally safe
2. Easy to install due to its flexible, compressible nature, comes in rolls and can be cut to size or shape desired, stuff it in the hole, and youâ??re done.
3. It is a permanent solution, will not rust or corrode over time, dose not shrink, stain, pull out.
4. Made of sharp durable fibers material which is suitable to die cut to specific shapes and sizes.
5.Most consistent material for exhaust applications with strength in all directions as cross-lapped material going at approximately 90 degree angles to other fibers.
6. Installs under landscaping and allows grass and small plants to grow through, thus being an invisible force against pests.
C):Function:
1. Fill fabric is an exclusion fabric used by professional nuisance control and pest control operators.
2. It is composed of stainless steel and poly fibers. This blend of materials gives it an extra â??spring backâ?�, allowing for easier fitting in crevices and the ability to stay in place well. Cut it 2-3 times the size of the opening to make a tight fit.
3. It is highly resilient and is an impenetrable barrier against rodents and pests.
D):Application
Burrowing animals such as rats, chipmunks, gophers, groundhogs and nutria can dig beneath the ground and ruin landscaping, chew through cables and destroy dikes and levees. Prevent these animals from wreaking havoc beneath the ground, currently protecting many public and private sites including:
Tree pits
Shopping mall landscapes
Planters
Parks
Sports fields
River and canal banks
Retention ponds
National historic sites
Outdoor amphitheatres
E):Install Instructions
1. Install it by pressing it into rodent-prone crevices with gloved hands or simple tools like a putty knife or screwdriver.
2. Do not install it close to live electrical conductors, since stainless stell is an electrical conductor. Installing IT around fully sealed electrical conduit coming out of a wall is safe.
PU Stainless Steel screen panel also named Stainless Steel Perforated Steel Modular Panels
Stainless Steel screen panel has following applications:
1?Wear resistance, corrosion resistance, long service life
2The mesh is varied to meet various mines requirements
Stainless Steel screen panel has following applications
Stainless Steel screen panel is widely applied to screen the metallurgy, mining, coal, quarry and other granule materials.
The customization of Stainless Steel screen panel:
The conventional thickness of Stainless Steel screen panel: 3-5mm
Overall Dimensions:Dimensions can be customized by customers
Mesh shape:Round,oblong, hexagon
The price is determined by the customized product
17884 Stainless Steel Suppliers
Short on time? Let Stainless Steel sellers contact you.
Product information:
The stainless steel banding can guarantee extended service life; and attaching under significant mechanical loads. Minimal breaking load is also different depends on the grade of steel.
Jeraâ?? stainless steel straps are available in different sizes to assist your strapping needs of securing with heavy loads.
Grades 201 202 304 316 409
1/4" - 6, 4 mm0.015" - 0, 40 mm
3/8" - 9, 5 mm0.020" - 0, 50 mm
1/2" - 12, 7 mm0.025" - 0, 64 mm
5/8" - 16, 0 mm0.028" - 0, 70 mm
3/4" - 19, 0 mm0.030" - 0, 75 mm
Stainless Steel Wedge Wire Drain is made of SS304 SS316 material. It has advantages
of surface , fast water draining, anti-odor, anti-clogging, easy to maintain and clean
etc. Our Wedge Wire Grate are highly and widely accepted by our customers around
the world, such as USA, Australia, Canada, Germany, Poland, New Zealand etc.
Size Table
Profile Wedge Wire: 3mm*4.2mm
Profile Wedge Wire Interval: 3mm
Support Bar: 3mm*6mm
Center Distance of Support Bar: 25mm
Frame on Four Sides: 20mm*5mm
Length Width Height
SS304 within 3m within 40 cm 20 mm
SS316 within 3m within 40 cm 20 mm
We have stock for wedge wire grate with standard sizes, so you will get the goods
on time when you nedd it urgently. Besides, we can also customize them according
to customers' requestment.
Wedge Wire Grate can be used in Bathroom ,Balcony ,Kitchen. swimming pool and
floor drain.
Advantages
1.Drainage fast , always keep the bathroom dry and clean, enhance the level of
non-slip surface
2.Increase three dimensional sense of space ,do not use stone to separate dry
and wet areas again ,and don't use any other Stainless Steel Linear Drain
3.Save the time of construction, using the drainage of same gradient, construction
of simple ,maintain tile integrity and beautiful appearance .
4.Security increased ,it is a trouble free access for some people whose action is
inconvenience as it do not need the stone to separate dry and wet areas
5.Beautiful appearance ,to be part of the bathroom , become a kind of elegant
decoration
Stainless Steel SS 304 316 Round Podium Drain
Company Information
Century Woven (BEIJING) Corporation is a professional manufacturer and
exporter in china, with more than 15 years experience in manufacturing and
exporting stainless steel linear floor drain.
We got mature experience from many times of cooperating with bathroom
accessories merchant around the world, especially in USA and Australia.
We have got water mark certification.
We look forward to the opportunity to serving you.
Packaging & Shipping
Packing
1.grate: 1PC/polybag, several in wooden pallet
2.grate+trough: 1pc/carton box, several in wooden pallet
3.or as customer requests
Transportation
Delivery Detail: Shipped in 7-30 days after payment
If you have any other question, pls feel free to contact us as below
Normal SS ring (4CM),Rs.4.50
Coating (4CM),Rs.7.95
Antique (4CM),Rs.7.95
Mat Finishing (4CM), Rs.5.90
Square- Normal (4CM),Rs.7.95
Square - Empose (4CM), Rs.7.95
Aluminium (4CM), Rs.5.75
We produce all kinds of stainless steel shackles including us type, eu type, jis type, dee type, bow shackle, security shackles and so on, u ara welcomed to inquiry us
ABOUT THE METAL SAND
1. Prolong service life of components so as to reduce production cost remarkably. The service life of metal sand as filter material is extended over 3 times than conventional filter materials such as glass bead,sea sand and silicon carbide.
2. Thanks to its high degree of profile ,large specific surface and strong impurities filter capability,the use of metal sand prolongs the service life of components,reduces use of auxiliary materials(strainer and washer,etc.)related to components,cleaning expenses of components and consumption of manpower as well as loss of capacity,etc.
3. Decrease the rate of broken filament and end breakage,the characteristic of irregular concave-convex acute angle in metal sand is far advantageous over conventional filter materials,such acute angle is very high in hardness and not easy to deform under 40Mpa pressure and can well puncture air bubbles in melt and obstruct foreign matters and coagulated particles so as to improve filter precision.
4. Stabilize pressure on components and the process of pressure rise is slow and stable to avoid fluctuation of production and unstable quality due to unstable pressure,and thus metal sand will not change its shape with changes of melt pressure and temperature.
5. Enhance homogeneity and spinnability of melt,stainless steel is a good conductor of heat and can guarantee homogeneity and consistence of temperature of high-temperature melt in sand bunker of components.
6. Stable chemical properties prevent adverse reaction with polyester melt.
7. Convenient use without need of cleaning and drying required for glass bead,sea sand and silicon carbide.We have conducted high-pressure cleaning process during production,so the delivered products are free of dust.
THE CONTENT OF ElEMENTS
Elements
C
Cr
Ni
Mo
Si
Mn
Fe
Qualified scope%
0.1-0.2
17-22
4-13
1-3
1.5-3
0.4-0.7
Basicingredient
Note:metal contents can be adjusted in accordance with the requirements of customers.
PACKING DENSITY(UNIT:(G/CM3)
Size micron(micron)
Size mesh(mesh)
Density(g/cm3)
1651-833
10-20
1.2-1.5
833-350
20-40
1.6-2.0
350-245
40-60
1.65-2.3
245-198
60-80
1.7-2.6
198-165
80-100
1.8-3.2
NOTE:
A. Testing method for packing density:place an empty beaker in a certain size cm3 rest on platform,and the metal sand in corresponding size fall freely into the beaker at a place in distance of 20cm from the opening of beaker.Stop falling of sand when the beaker is full of sand with a slight overflow,strike off along the opening of beaker with a flat ruler and weigh the sand,divide the weighed net grams by the volume of beaker is the packing density of this size.
B. The above packing density is only for reference,specific packing density for practical use should be determined according to the requirements of enterprises for production sizes and pressure on components.The established sized and corresponding packing densities by both parties should not be altered at discretion and be regarded as important indicators for inspection of incoming and outgoing goods by both parties.
C.In addition to common sizes,screening and matching can be performed as required by customers.
APPLICATION METHOD OF METAL SAND
1. This metal sand has been strictly cleaned and screened during production without need of
cleaning and screening once more during application.
2. Before assembly sizes should be seen clearly and confirmed without error.
3. At the end of each application,please well bind internal bag for residual metal sand to avoid entry of dust and impurities to affect normal use.
4. Several sizes can be used in layers,either one size can be used independently.For matching use of a few sizes,it would be the best to separate with corresponding single-layer stainless steel mesh between layers for better filter effect.The closer to the spinning head,the higher the meshes of sand (the thinner the sand).
5. In accordance with the requirements of productive technology,weigh metal sand and put into sand bunker,knock the case of sand bunker in all directions with copper rod to let sand increase density under vibration,and then compress the surface of metal sand in sand bunker with even end of stainless steel bar (which is approximate 15cm long and must be smooth and glossy)with diameter slightly less than that of sand bunker,and apply approximate 10kg pressure clokwise or anticlockwise and rotate to level the surface of metal sand,afterwards place a dedicated sand pressing bar with smooth and glossy surface in diameter of 1.5mm less than the inner diameter of sand bunker under the press to squeeze metal sand with a pressure of about 11Mpa to maximize its density.Nonhomogeneous densities and different sizes of dischargde filaments in the same sand bunker should be avoided.
6. During assembly of compinents the sand bunker must be filled with metal sand without void,which especially important for assembly of combination of a few sizes.
7. When the metal sand manufactured by our company is used,the speed of pressure rise of components is low and even the pressure does not rise for long time,this is a normal phenomenon;after the pressure rises up to the maximal technological pressure,please replace compinents in time in case that minconforming products are manufactured.
8. This product is a one-off product and cannot be reused after the first use.
9. Since the service life of components is longer due to use of metal sand manufactured by our company,so enterprises using the metal sand should make follow-up records for components loaded in machine.For convinience of quality management,it would be the best to replace components up to the approved service cycle(because as of now it is impossible for chemical fiber enterprises to install pressure gauge at each position),and meanwhile regular silicon dressing of spinning plates should be conducted in order to ensure stable quality and normal continuity of production.
SAMPLE FIGURE OF STAINLESS STEEL METAL SAND UNDER HIGHLY MAGNIFYING ELECTRONIC GLASS
ABOUT THE METAL SAND
1. Prolong service life of components so as to reduce production cost remarkably. The service life of metal sand as filter material is extended over 3 times than conventional filter materials such as glass bead,sea sand and silicon carbide.
2. Thanks to its high degree of profile ,large specific surface and strong impurities filter capability,the use of metal sand prolongs the service life of components,reduces use of auxiliary materials(strainer and washer,etc.)related to components,cleaning expenses of components and consumption of manpower as well as loss of capacity,etc.
3. Decrease the rate of broken filament and end breakage,the characteristic of irregular concave-convex acute angle in metal sand is far advantageous over conventional filter materials,such acute angle is very high in hardness and not easy to deform under 40Mpa pressure and can well puncture air bubbles in melt and obstruct foreign matters and coagulated particles so as to improve filter precision.
4. Stabilize pressure on components and the process of pressure rise is slow and stable to avoid fluctuation of production and unstable quality due to unstable pressure,and thus metal sand will not change its shape with changes of melt pressure and temperature.
5. Enhance homogeneity and spinnability of melt,stainless steel is a good conductor of heat and can guarantee homogeneity and consistence of temperature of high-temperature melt in sand bunker of components.
6. Stable chemical properties prevent adverse reaction with polyester melt.
7. Convenient use without need of cleaning and drying required for glass bead,sea sand and silicon carbide.We have conducted high-pressure cleaning process during production,so the delivered products are free of dust.
A world class manufacturer & supplier of lost wax investment castings in carbon steel and alloy steel, is one of the large-scale professional investment casting production bases in China, consisting of both casting foundry & machining factory. Annually more than 7000 tons Precision casting parts are exported to markets in Europe,America and Japan.
2. OEM casting service available according to customers requirements.
3. The materials could be cast by investment casting are very diversified. The material have been explored by our company are more than 80.
4.The material standards adopted include National Standards GB, United States Standards ASTM, AISI, Germany Standards DIN, Briitish Standards BS
5.The applications of our products cover almost the whole mechanical manufacturing and processing application fields , such as mining , Engineering machinnery , oil , ships , railroad, automobile , electric machine, hardware, agricultural machinery, appliances, construction. Our company has explored and produced more than 1000 different product.
6. Our products are widely applied and almost covered all applicable fields that involves equipment manufacturing & mechanical manufacturing industries, mainly including trains and railways, mining and engineering machinery, automobile, ships, petroleum machinery, agricultural machinery, construction, valve and pumps, electric machine ,hardware, power equipment and so on. We produce according to customersdrawings or samples, focus on the material categories of carbon steel and low alloy steel. Up to the present, more than 100 specific material specifications and 3,000 kinds of products have been developed and produced in our company. We are proficient in performing various industrial standards, such as Chinese GB, American ASTM, AISI , German DIN, French NF, Japanese JIS, British BS, Australian AS and Association of American Railroads (AAR )and other industrial standards.
1.material: stainless steel 201
2.finish:polish
3.size: 1800*38*1.5mm
4.packing: 60pcs/knit bag,special packing is accepted.
5.professional piano hinge manufacturer in China
6.factory direct offer with good quality and competitive price
7.can accept OEM
1.packing: 60pcs/knit bag,special packing is accepted.
2.weight:1.15kg/pcs
3.packing size: 1840*70*70mm
1.material: stainless steel 304
2.finish: mirror polish
3.size: 25meter( length)*30mm(open width)*0.5mm(thickness)
4.packing: packing in roll,one roll/knit bag,special packing is accepted.
5.factory direct offer with good quality and competitive price.
6.professional piano hinge manufacturer in China near ten years.
7.automated machine produce line.can delivery quickly.
Duplex 2507 is a super duplex stainless steel designed for applications which demand exceptional strength and corrosion resistance. Alloy 2507 has 25% chromium, 4% molybdenum, and 7% nickel. This high molybdenum, chromium and nitrogen content results in excellent resistance to chloride pitting and crevice corrosion attack and the duplex structure provides 2507 with exceptional resistance to chloride stress corrosion cracking. Usage of Duplex 2507 should be limited to applications below 600�?�° F (316�?�° C). Extended elevated temperature exposure can reduce both the toughness and corrosion resistance of alloy 2507. Duplex 2507 possesses excellent mechanical properties. Often a light gauge of 2507 material can be used to achieve the same design strength of a thicker nickel alloy. The resulting savings in weight can dramatically reduce the overall cost of fabrication. The advantage of a duplex structure is that it combines the favorable qualities of a ferritic alloy (stress corrosion cracking resistance and high strength) with those of an austenitic alloy (ease of fabrication and corrosion resistance). Usage of 2205 Duplex stainless steel should be limited to temperatures below 600 F. Extended elevated temperature exposure can embrittle 2205 stainless
Duplex 2205 is a nitrogen-enhanced duplex stainless steel that was developed to combat common corrosion problems encountered with the 300 series stainless steels. Duplex ? describes a family of stainless steels that are neither fully austenitic, like 304 stainless, nor purely ferritic, like 430 stainless. The structure of 2205 duplex stainless steel consists of austenite pools surrounded by a continuous ferrite phase. In the annealed condition, 2205 contains approximately 40-50% ferrite. Often referred to as the work horse grade, 2205 is the most widely used grade in the duplex family of stainless steels
The advantage of a duplex structure is that it combines the favorable qualities of a ferritic alloy (stress corrosion cracking resistance and high strength) with those of an austenitic alloy (ease of fabrication and corrosion resistance). Usage of 2205 Duplex stainless steel should be limited to temperatures below 600 F. Extended elevated temperature exposure can embrittle 2205 stainless.
Stainless steel conductive fabrics are a type of fabric made from stainless steel fibers that have been woven or knitted into a textile. These fabrics are designed to have electrical conductivity, which makes them useful for a wide range of applications, such as electromagnetic shielding, heating elements, and wearable technology.
The electrical conductivity of stainless steel conductive fabrics comes from the presence of stainless steel fibers, which are made from a blend of stainless steel and other metals. These fibers are typically very fine and can be woven or knitted into a fabric using traditional textile techniques.
One of the main benefits of stainless steel conductive fabrics is their ability to shield against electromagnetic radiation. This makes them useful for applications such as electromagnetic interference (EMI) shielding in electronics and communications equipment. They are also used in medical applications to shield against electromagnetic fields generated by medical equipment.
Another use for stainless steel conductive fabrics is in heating elements. Because of their electrical conductivity, they can be used to create heating elements for clothing, blankets, and other applications where heat is needed.
Stainless steel conductive fabrics are also used in wearable technology, such as smart clothing and fitness trackers. They can be integrated into garments to create sensors that track body temperature, heart rate, and other physiological data.
17884 Stainless Steel Suppliers
Short on time? Let Stainless Steel sellers contact you.
