BLUE JAY DC voltage panel meters with a DC signal conditioner board combine high accuracy with high read rate and a wide range of isolated output options for computer interface and control. Accuracy is 99.99% of full scale ±1 counts DC voltmeter operation provides and six full-scale voltage ranges from 200.00 mV with 10 mV resolution to 600.0 V with 5V resolution. The 200.00 mV and 2.000 V ranges provide a high input impedance of 1 Gohm to minimize the load on the voltage signal. All voltage and ranges are factory calibrated, without recalibrating the meter.BLUE JAY DC voltage panel meters with a DC signal conditioner board combine high accuracy with high read rate and a wide range of isolated output options for computer interface and control. Accuracy is 99.99% of full scale ±1 counts DC voltmeter operation provides and six full-scale voltage ranges from 200.00 mV with 10 mV resolution to 600.0 V with 5V resolution. The 200.00 mV and 2.000 V ranges provide a high input impedance of 1 Gohm to minimize the load on the voltage signal. All voltage and ranges are factory calibrated, without recalibrating the meter.
Especially developed for indication and supervision of the single-phase circuit, replaces an analogical ammeter, reducing installation manpower and optimizing the used one of spaces in the panel. Ideal for protection of single-phase networks is monitored and generally to own alarm superior and inferior. Protection of the parameters of programming by password. Specifications Current inputs (TRMS) Communication (Option) CT primary 10 000 A Link RS485 CT secondary 1 and 5 A Type 2 ... 3 wires half duplex Sampling Rate 2 per sec Protocol Modbus RTU mode Resolution 0.001 to 1, depending on the range MODBUS speed 4800/9600bauds Burden < 0.5VA, < 0.2VA in 20A Analog Outputs (Option) Auxiliary power supply Number of outputs 1 channel AC voltage DC/AC 85~265 ± 30 % Type Isolated Frequency 50 / 60 Hz Range 0 / 4 ... 20 mA or 0-5V Consumption < 10 VA Maximum current 30 mA Front panel Alarm Outputs (Option) Display Type Red LED Super Bright Display Number of relays 1 channel Maximum Display 9999 Counts Type Passive nodes Polarity Indication "-" is indicated for negative input(option) Weight Case / Housing Material Approximate 250~400g Installation Panel mounting Environment Terminal Block Thermoplastic with Tin Plated Brass Terminal Calibration 27°C ± 5°C Dielectric Strength Operation 0 to 50°C, RH < 70% 2.5 kV at 50Hz for 1 min Storage -10 to 60°C, RH < 70%
Intelligent temperature & humidity controller with completed FUZZY algorithm provides very precise of temperature monitor. FUZZY algorithm control fan or heater to maintain sensible & latent capacity follows temperature/humidity curve by automatically. Display unit can show environment temperature and humidity as per configure by user. The user also can adjust environment condition very easily.
Electronet series ELMAG-200 are micro-controller based full bore type electromagnetic flow meters specially used for various industrial applications. These flow meters accurately measure the flow rate of conductive liquids & slurries in closed pipes. Due to its simple and rigid design, the flow meter is an obstruction-less and maintenance-free instrument in place of conventional mechanical flow measuring devices. The use of 'Pulsed DC' technology offers highest ability and better measuring accuracy in the form of electrical signal 4-20 mA DC linearly proportional to volumetric flow. A magnetic field is generated by the instrument in the flow tube. The fluid flowing through this magnetic field generates a voltage that is proportional to the flow velocity. Corresponding electrical output is provided with respect to measuring flow range.
Electronet series ELMAG-2516 are micro-controller based full bore type electromagnetic flow meters specially used for various industrial applications. These flow meters accurately measure the flow rate of conductive liquids & slurries in closed pipes. The use of 'Pulsed DC' technology offers highest ability & better measuring accuracy in the form of electrical signal 4-20 mA DC linearly proportional to volumetric flow.
Data: 1.Measuring current:0-5A 2.Measuring voltage:0-100V 3.Accuracy class:1.5 4.Operating temperature:-20~50 5.N.W:195G G.W:245G 6. Product Description Composition: Glass window, ABS Resin frame and case, PC glass fiber base mounting fitting included. Scale Plate: The normal scale plate is made of alloy-aluminium material white printed with black scales,Values, units, technique symbols, etc. Scale plate with special requirements are available upon request. Such as color, scale with lighting functions and PVC noctilucence are available upon request. Color: Black base and frame , white scale plate and meter body. Pointer: Normaly, the pointer is made of alloy-aluminium, it is black, and red, white are available Upon request. Anti-static: All meters are subject to anti-static treatment to minimize the static-effect to the accuracy of the meters. Damping and Overshoot: The overshoot is less than 15% when the pointer is at the 2/3 of the scale. Damping and overshoot can be customized according to userâ??s requirements. Accuracy: BE-96W A/V-Class 1.5 BE-96W COSΦ-4degree in phase angle BE-96W HZ-Class 1.5 FULL SCALE DEFLECTION:250 degree Service condition: -20~+50 degree; Operating position: Generally, meter is installed in vertical position. Other installation position can be customized (please specify the desired angle).The accuracy class is just valid for the Corresponding installation mode. Insulation Test: The test Voltage for BE&BP series is 2KV RMS for 1 minute with the frequency 50Hz. Safety Precautions: Meters with damaged bezels or glass faceplates must be disconnected from the mains. Scale plate, front frames and windows may only be replaced under voltage-free conditions. The meter should be kept clean, if the meter is used in a manner not specified by the manufacturer, the protective function may be impaired. Meters with Auxiliary Lighting In order to read the indicating values in darkness,KDSI provides Meters with lighting functions.Power can be AC/DC:12V,24V,110V.
SA2100 Class S Power Quality Analyzer Overview SA2100 is a handheld multi-functional device which is designed to measure and analyze single or three-phase power system. This portable class S device can provide safe, convenient and accurate measurements for troubleshooting power networks. SA2100 Portable Power Quality Meters Portable Power Quality Meters enable electricians and facility maintenance professionals to troubleshoot and benchmark power quality problems over time. They help you identify energy waste in your facility and detect and prevent power problems before they occur. Why do you need Power quality meter analyzer? Portable Power Quality Meter identifies power quality problems that often manifest themselves as dips, spikes, harmonic distortion, imbalances, flicker and transients. Power quality determines the suitability of electrical energy to drive motors, machines and other end-user equipment. Poor power quality can affect the ability of these devices to operate properly, which can lead to malfunctions, premature failures or possibly cause them to not work at all. Most power quality analyzers monitor total harmonic distortion, phase angle, power factor, balance, etc. to get a complete picture of the system.
Laser Source Power Meter The Laser Source Power Meter provides an economical, stable laser source for point-to-point attenuation measurements. It features a rugged design that withstands the harsh test environments of fiber optic cable installation and maintenance.
PH meter Description Online pH / ORP meters and pH / ORP controllers are one of the most common water quality analysers in use today in water treatment and process plants and yet online pH / ORP meters cause continual problems for their operators. What is needed is a stable, reliable, online pH/ ORP analyzer for a reasonable cost. That is exactly what you get with the BOQU Instrument. A pH and ORP meter consist of a pH or ORP sensor, transmitter and process adaption, combined to best suit your pH control needs. The online ORP meter from BOQU Instrument provides accurate process pH measurements in a wide range of environments, from ultra pure water to hygienic measurements in a bioreactor to dirty chemical production. Our Advantages 1ã??Stable, Reliable,Precision,Continuous measurement pH,ORP and Temperature. 2ã??Instrument for panel mounted,wall mounted,pipe mounted. 3ã??2 ways of 4-20mA and standard RS485 Modbus RTU 4ã??Instrument provide High/Low control relay 5ã??Local Data logger function for 1000 times 6ã??Application:industrial waste water, drinking water environmental monitoring, ultra pure water,fermentation, food production process etc. If you need our online ph meter, you can contact us through our online chat window.
Online pH / ORP meters and pH / ORP controllers are one of the most common water quality analysers in use today in water treatment and process plants and yet online pH / ORP meters cause continual problems for their operators. What is needed is a stable, reliable, online pH/ ORP analyzer for a reasonable cost. That is exactly what you get with the BOQU Instrument. A pH and ORP meter consist of a pH or ORP sensor, transmitter and process adaption, combined to best suit your pH control needs. The online ORP meter from BOQU Instrument provides accurate process pH measurements in a wide range of environments, from ultra pure water to hygienic measurements in a bioreactor to dirty chemical production.
Common Meter Reading Instrument (CMRI) is a handheld computer used to download data from electronic tri-vector meters, supporting different protocols like IEC, ANSI and PACT. CMRI is also compliant to IS-15959/ DLMS (IEC-62056) standard. CMRI can be interfaced with the portable printer for spot billing applications. SANDS CMRI-1010 comes with LCD Graphical (3.5â?? TFT) & 15Line x 40 Characters visibility is rugged to withstand drop on to concrete and waterproof. CMRI is available with a memory size of 512 MB. Features Electronic reports for Static Tri-Vector Meter data No manual intervention & error-free reports Universal report generation irrespective of meter make Reports affecting activities like energy accounting, technical loss. calculation & deriving industry load patterns HT service meter reports in comparison to the respective Feeder Meter data Consolidated consumer reports for quick reference for higher-level management High Speed (HS) communication Complied with Common DLMS S/W ACCESSORIES Optical Probes Universal Probe for Multiple Protocols Zero Powered Probes USB type probe (USB 2.0) Impact Printer 2 Inch paper width High speed printing Long ribbon life RS-232/Bluetooth Interface
The DLMS meter reading application runs on Android mobile devices. It is an effective and efficient meter reading solution for DLMS meters (IEC-62056) & Smart meters (IS-16444). This application supports reading and Real-time viewing of field meter profiles, data view, programming the meter, smart meters connect / disconnect. This is also a solution to address the last mile connectivity issues- where the AMR and AMI networks failed due to network problem. Features SANDS DLMS meter reading application is an effective solution for reading, configuring, and controlling the DLMS meters. Simple and user-friendly GUI. Supports all leading meter manufacturers DLMS meters (Tested with 30 makes of both single-phase and three-phase meters). Real-time data profile view, using compact BCS supports both graphical and tabular report formats.
IOT-Based fastest tri-axial vibration & Noise (10kHz) in a single analyzer in the market (Data Refresh rate every 1 sec). Quick collect, route based collect and vibration analysis in a single unit. Monitor a broad range of machinery â?? from variable speed machines, complex gearbox, high-speed spindles & Low speed bearings. Wireless MEMS based tri-axial vibrations measuring range up to +/- 16g & Sampling rate 26.7 kHz. Offers Velocity, Acceleration and displacement â?? Overall RMS values, TWF & FFT Spectrums. AI & ML based alerts will give the health condition of the equipment as per ISO-10816 standards. Routine data collection and Real Time spectrums can be viewed and logged to mobile app
IoT Power Meter A IoT power meter is a data-transmitting meter that helps industries monitor and manage three-phase power consumption. It transmits real-time energy consumption data to a server in the cloud, allowing for better management of energy consumption and industrial equipment. Acrel ADW300 energy meter is mainly used to measure three-phase active electric energy of low-voltage network, with RS485 communication and 470MHz wireless communication function, which is convenient for users to monitor, collect and manage electricity consumption.
Smart Energy Meter IoT With Internet of Things (IoT) enabled solutions for smart metering, you can improve customer service and increase profitability with actionable smart meter data insights. Internet of Things Smart Meters Traditionally part of the grid infrastructure, smart meters are electronic devices that can remotely monitor and record energy consumption. However, in the era of IoT and IoT platforms, standalone smart meters are giving way to more advanced and versatile smart metering solutions. These solutions offer a wider range of remote monitoring and alerting capabilities, as well as powerful data analytics tools to help companies and individual users optimize their energy, water, gas or fuel consumption. Smart Metering Solutions with Acrel IoT Cloud Platform Through the wireless network, you can check the status of IoT devices located across the country anytime, anywhere, and simply view data such as energy consumption and alarm reports. Energy Analysis and Reporting This page displays daily, monthly, and yearly energy graphs, while energy reports can be automatically generated in Excel format for export. Parameter Monitoring Monitor all parameters collected by IOT devices, can generate historical curves, and alarm based on parameter monitoring. Alarm report When a potential threat such as over-current, over-voltage or over-temperature occurs, it will be added to the alarm report and notify the user for current alarm. Alarm Handling Once the alarm occurs, the most important thing is to deal with the possible faults at the site in time, by sending the alarm processing to the site, in order to solve the problem in time.
Product Introduction The wet gas flowmeter is a volumetric gas flowmeter. Its measurement range ranges from 0.016L/min for small flow to 200L/min for large flow. It has high accuracy, no leakage, and good stability. It is suitable for gas volume or flow measurement in laboratories, research institutions, environmental measurement, production sites, etc. It can also be used as a transmission standard and working standard, and is widely used in gas appliances, energy, chemical industry, environment, medicine, calibration and other industries. The products have been exported to Europe, America, Asia and other countries and regions. � Product Features 1. Extra-wide flow range 1:300 2. Repeatability better than 0.1% 3. Intelligent correction (Volume and flow rate automatic correction) 4. Various automatic measurement methods (constant volume output, timing output, and fixed whole revolution output) 5. Full digital flow meters (Temperature, Pressure, Volume, High-precision measurement of flow, RS485 Bus Communication) 6. Intelligent wire control start and stop 7. Each is strictly calibrated with � 0.05-stage active piston prover to ensure accuracy 8.� No leakage (using advanced magnetically coupled transmission technology, non-oil seal) � Precision (Repeatability) Standard Flow Range: �± 0.1% (Standard deviation) Entire Flow Range: �± 0.15% (Standard deviation) � Material (Anti-corrosion) 304 stainless steel 316 stainless steel (customized) Temperature measurement: 0-50 Pressure measurement: 0-10kPa
DDS5558 Single Phase Meter is a kind of new style single phase two wire active energy meter, it adopts micro-electronics technique, and imported large scale integrate circuit, use advanced technique of digital and SMT techniques, etc. It has minimum size, and also a new single phase two wire active energy meter. It has already passed the test of the international authority CE. The meter completely accords with relevant technical requirements of class 1 single phase active energy meter stipulated in international standard IEC 62053-21. It can accurately and directly measure 50Hz or 60Hz active energy consumption from single phase AC electricity net. This meter has white backlight source eight digits LCD monitors shows the active energy power consumption. It has following features: Good reliability, small volume, light weight, specious nice appearance, convenient installation, etc. Features: Bi-directional total active energy measurement 25mm standard DIN rail installation, complying with standard DIN En50022. Single pole width (Modules17.5mm), complying with standard DIN43880. Small modular size, DIN rail mounted. Easy installation to distribution boards, load center, miniature & etc. by identifying where energy is being used. Application: All power parameter measurements; Energy measurement and electrical fire monitor and control; Replacing the three-phase power meter, three-phase electricity transmitter; Transformers, generators, capacitors, and electric motors distributed detection; Medium and low-pressure systems; SCADA, EMS, DCS integrators.
DCM3366D series electronic DC energy meter is a new generation product produced by our company. It adopts a liquid crystal display and has an RS485 communication function for data exchange with a microcomputer. It is suitable for power measurement and energy metering of DC signal equipment such as batteries and solar panels. It can also be used in modern supply and distribution DC systems such as industrial and mining enterprises, civil buildings, and building automation. It is composed of a measurement unit, data processing unit, communication unit, display unit, etc., and has the functions of electric energy measurement, data processing, real-time monitoring, and LCD. The electric energy meter has the characteristics of high overload, high accuracy, low power consumption, automatic saving of power outage data, and long life. Rated voltage (Un): DC100V, DC300V, DC500V, DC1000V Rated current (Ib): 50A, 100A, 200A, 300A, 500A, etc. can be set (maximum measured value 4800.0000A), using an external 75mV shunt input Auxiliary power supply: power supply voltage, DC20Vï½?60V or AC85ï½?265V/DC85ï½?330V optional Working temperature range: -25â??ï½?60â?? Dielectric strength: Voltage/power supply/casing: 3.0kV/min Communication/power supply: 3.0kV/min Static electricity immunity: contact discharge 8 kV, gas discharge 15 kV Electrical fast burst immunity: 4kV Surge immunity: 2kV/4kV
Plastic housing made of PP, POM or PA, rust free for water flow. Vertical or horizontal installation, easy to set up for different applications. Sensitive start up volume setting and accurate to measure volume. Features of plastic water flow switch Multiple mounting options: can be mounted vertically or horizontally. Different connecting options: barbed connector or threaded connector with different sizes. Wide range of application with working temperature up to 100â??. For more information about pvc pipe flow switch and buy position sensor, please feel free to contact us!
DM400 Chemical Moisture Meter High Frequency moisture meter DM400 is our new designed product with separate probe .It used for measuring moisture content of soil ,silver sand, chemical combination powder, coal powder and other powder materials. It applicable of chemical industry and other relevant industry. Features: * It is portable, compact, easy to use and the moisture measurement readings are instant. * Digital display with back light gives exact and clearly reading although you stay at the somber conditions. * This instrument adopted the high frequency principle based on the introduction of the most advanced technology from foreign country. * Low battery alert. Specifications: Display:4 digital LCD Measuring range : 0.00%-2% 0.0%-90% Measuring conditionï¼? Temperature:0-60°C Humidity:5%-90%RH Resolusion:0.1 or 0.01 Accuracy: ± 0.5%n Power supply: 9V battery Dimensions: 172Ã?66Ã?28ï¼?mmï¼? Needleï¼?450mm Weight:250g
