Ecoplus Interior Emulsion is a high quality water based paint suitable to use for interior application and protection of surface walls, ceilings, particle boards etc. It is available in wide range of attractive shades.
Emulsion paint consists of tiny polymer particles within which the pigments are trapped.
For price, specification and other details please contact us
High grade universal spray with 8-fold action: dust remover, lubricant, cleaner, penetrating oil, anti-corrosive, damp repellent, shock and contact spray. It does not corrode plastics or metals and leaves a protective film on surfaces after use.
Universal spray
8-fold action
Can be used on metals, plastics and rubbers
Aerosol can be used at any angle (360�°)
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Metal cutting fluid In actual production, even high-quality metal cutting fluids must be added with a certain amount of bactericidal and algae-removing agents to extend the service life and increase the utilization rate. PSC80626, whether used as a metal cutting fluid additive, a settling agent or a water-based cutting fluid, can accelerate the sedimentation of metal chips, accelerate the separation of water and oil in the cutting fluid, effectively reduce the growth of bacteria, and extend the life of the metal cutting fluid. PSC80626 is used in fully synthetic metal cutting fluids for water machines, and the amount is very small, and the additive formula can be adjusted flexibly. As a settling agent, it is basically consistent with Buckman's Busan 77 in terms of theoretical map test data, which can completely replace this type of product and has a significant effect in actual use.
We would like to introduce Awesome paints which has come a long way ever since it's establishment in the year 2014, and has established a strong foothold in the market. We have come to be recognized as an eminent importer, exporter and consultant of Acrylic washable Distemper (water base no VOC paint).
Made using superior quality raw materials our products are meet with international standards.
Export business is one of our prime objective and we are exporting our products WORLDWIDE.
Now, we are focusing to develop business in GLOBLE MARKET Being our valuable representative in GLOBLE MARKET, we need your help / support to establish new trade relationship with GLOBLE MARKET. So we request you to kindly provide us details of the buyers, importers, wholesale
rs and traders of our above mentioned product to communicate with them and to establish new business relationship.
We are forwarding below our company details for your kind reference.
Company Profile
Business Type:
Exporter
Primary Competitive Advantages:
Standard Product Quality
Competitive Price
Delivery on Time
Customer Oriented Approach
Year of Establishment:
2014
Export Markets:
Russia, Kuwait, Nepal, Middle East, European Union, USA, Africa and Pakistan (Spreading Services Speedily)
OEM Service Provided:
Yes
Annual Production Capacity:
60lakhs and more per month
Product Range:
Acrylic washable distemper with different size of packing
Membership:
Registered Member under Government of India (FIEO)
Focus Industries:
Chemicals Industry, Decorative Industry, Paint Industry,Trading Companies, Distribution Companies, Agents.
We believe in providing prompt delivery, best quality & most competitive price.
We would also be thankful if you could kindly give us the details of leading Business to Business magazines, Trade web portals and "Directories" relating to our product.
We look forward to receive your soonest and positive reply and the details.
Highly finish wall guard putty give finish surface as well as whiteness. All fill the dent and rust area. Our bag is not harm to worker and atmosphere . Itâ??s also loyal rate. And give higher covering
1, With very good adhesion, can dissolve much iron oxide in metal surface, makes very strong combination with metal body.
2, Can be combined with cover coat in high level.
3, With very good elasticity and compressive strength. Prevent and decrease damage due to mechanical stress.
4, With less viscosity and surface tension, its good for escape of gas when firing. Reduce bubbles on cover coat. To ensure the smooth surface of enamel products.
5, With suitable expansion coefficient similar as steel plate.
ABOUT US
vitreous enamel coating porcelain enamel steel grates enamel glaze fritHunan Noli Enamel Co., Ltd
is the leader manufacturer of enamel frits & inorganic pigment in China.
Now we have 30,000 M/T enamel frits and 2,000 M/T inorganic pigments annual capacity, 10,000 M/T RTU(Ready to use) powder and electro static powder.
Our main products of enamel frits including ground coat, cover coat, transparent frit , matt enamel, direct on black frits and various cast-iron frits. High temperature inorganic pigment including Red& yellow, blue, green, black Oxide etc, widely used in porcelain enamel, ceramics, glass, coating,painting etc.
As an ISO9001:2008 certified manufacturer, we have strict quality control in the whole production process to guarantee the quality of products. We are supplying the best service for customer.
100% of Our goods are exporting to USA, Europe, Middle East, Southeast Asia, South America, & Africa.
FAQ
Q1. Are you factory or trading company ?
We are a factory.
Q2. Whats the MOQ ?
Inorganic pigment MOQ is 25kg, enamel frit, RTU powder and electronic static powder MOQ=200kg.
Q3. What is your principle for the samples ?
We offer free samples if you are willing to pay the shipping cost.
Q5. How about your delivery time?
A: Generally, it will take 15 days after receiving your advance payment.
Q6. What information should I let you know if I want to get a quotation?
A: Your base material, your application area (best to send your finished product picture), the physical parameters you require(acid resistance, adherence, color, etc) the quantity you need. If possible, you can send me your samples and we customize for you.
Q7.Why choose us?
1. Reaching a production capacity of 30,000 Tons/Year for Enamel frit, 10,000 Tons/Year for RTU & electronic static powder, 2,000 Tons/Year for Inorganic pigment.
2. 60% frits & pigment exported to US, Netherlands, Indonesia,Thiland, Vietanam, Korea, Chile etc 30 country.
3. Having over 30 technical experts of frits & pigment from domestic & overseas, focusing on technical development & product improvement.
4. Having complete quality control system, Strong technical supporting team is focusing on customer service in this world.
AT-66 is a kind of synthetic emulsion of styrene acrylic copolymer. It is good at water, alkali and scrubbing resistance. It has excellent performance in adhesion with the base materials. Therefore, it is very suitable for interior and exterior wall paints.
Polymer Type Styrene acrylic copolymer
Appearance Milky white liquid
Solid Content 48±0.5%
pH Value 7.0-9.0
Viscosity 800-2000 cps(Brookfield Viscometer , 3#/60rpm/25)
Average Particle Size 0.1 - 0.2 micron
Glass Transition Temperature About 25
Minimum Film Temperature About 18
Ionic Character Anionic
Applications
AT-66 can be used for interior and exterior wall paints.
At-3202A is a kind of styrene acrylate copolymer synthetic latex, without APEO and plasticizer, with good cement compatibility, water resistance, alkali resistance and excellent elongation AT break, especially suitable for the preparation of high-performance JS waterproof coating.
Appearance :milk white liquid
Solid content:54.5%-55.5%
PH: 7.0-9.0
Viscosity:500-2000 cps(3#60 rpm/25 centigrade)
Particle size :0.2-0.3 micron
Tg:-16 centigrade
MFT:0 centigrade
Ion features:anion
Use :make high performance JS water proof coating ,flexible putty.
At-3128 is a kind of vinegar tertiary acrylate copolymer, which is used to produce synthetic latex of water-borne metal antirust primer coating, and has good compatibility with antirust agent and antirust pigment.The products have excellent adhesion with metal substrate, resistant to water, salt water, salt fog, acid and alkali resistance.It has high weather resistance and yellowing resistance, suitable for metal rust - proof primer.
Appearance:milk white liquid
Solid content: 39%-41%
PH: 7.5-8.5
Viscosity: less than 1000 cps(3#60rpm/25 )
Particle size:0.0-0.2 micron
Tg:23
MFT:10
Ion feature :anion
BARILAC barrier coatings are the most suited sustainable solution to replace polycoated laminated board,
waxcoated, PVDC coated etc all non sustainable alternatives. Barilac barrier coat is recommended for
paper cup, trays, foodtrays, pizza boxes, ice cream cartons etc.
The special product features are.
- Low COBB
- Good oil and grease resistance
- Good Moisture Vapour Transmission rate
- Good heat sealing performance
- Good water resistance
- Low odour
- FDA compliance
Multi-purpose Spray Paint designed for interior & exterior application.
High Gloss and Quick Drying
Weatherproof, waterproof, rust proof
Acrylic Paint
Solid color and metallic color available
Primer and Lacquer
OEM Private Label acceptable
400ML Capactiy
Standard packing: 12pcs/box
