Product overview:
The series submersible sewage pump is mainly used for industry,agricultural,fishery,mine drainage,building construction, municipal environmental protection and tunnel construction etc. Trades to drain off soild particles with short fiber, confetti,sediment and so on. Or drain off software solids liquids. Such as mud,grey water, life wastewater, sewage and so on. The series submersible pump is the ideal equipment for agricultural irrigation,raising livestock and poultry manure pit,cleaning the silt of pool and construction site.
Usage:
Used for discharging waste water and other material with granular material, also it can be used for clean water and corrosive medium.
Conditions of using:
1.The medium temperature should not be over 40oC ,PH:4-10.
2.The solid volume ratio of the medium should not be over 2%.
3.The kinematic viscosity of medium between 7*10-7m2/s---23*10-6 m2/s.
4.The density of the medium is 1.2*10 3kg/m3.
5.Centered on the impeller,underwater not more than 5m.
Scope of application:
1. For discharging polluted waste water of factories and industries;
2. sewage discharge station of living quarters;
3. drainage system of municipal sewage treatment plant
4. drainage station of fire fighting system
5. waterworks equipment of running water factory
6. sewage discharge of hospitals and hotels
7. construction site of municipal engineering
8. matched equipment of exploration mine
9. country biogas digester
10.farm irrigation
11. other industries
Product overview:
The series submersible sewage pump is mainly used for industry,agricultural,fishery,mine drainage,building construction, municipal environmental protection and tunnel construction etc. Trades to drain off soild particles with short fiber, confetti,sediment and so on. Or drain off software solids liquids. Such as mud,grey water, life wastewater, sewage and so on. The series submersible pump is the ideal equipment for agricultural irrigation,raising livestock and poultry manure pit,cleaning the silt of pool and construction site.
Usage:
Used for discharging waste water and other material with granular material, also it can be used for clean water and corrosive medium.
Conditions of using:
1.The medium temperature should not be over 40oC ,PH:4-10.
2.The solid volume ratio of the medium should not be over 2%.
3.The kinematic viscosity of medium between 7*10-7m2/s---23*10-6 m2/s.
4.The density of the medium is 1.2*10 3kg/m3.
5.Centered on the impeller,underwater not more than 5m.
Scope of application:
1. For discharging polluted waste water of factories and industries;
2. sewage discharge station of living quarters;
3. drainage system of municipal sewage treatment plant
4. drainage station of fire fighting system
5. waterworks equipment of running water factory
6. sewage discharge of hospitals and hotels
7. construction site of municipal engineering
8. matched equipment of exploration mine
9. country biogas digester
10.farm irrigation
11. other industries
Flow: 15m3/h
Head: 26m
Power: 2.2kw
Material: cast iron
Medium: clean water
Outlet dia: 50mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province.
The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence.
Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Flow: 20m3/h
Head: 64m
Power: 7.5kw
Material: cast iron
Medium: clean water
Outlet dia: 60mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
Flow: 15m3/h
Head: 65m
Power: 5kw
Material: cast iron
Medium: clean water
Outlet dia: 50mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
.
5792 Industrial Pumps Suppliers
Short on time? Let Industrial Pumps sellers contact you.
Flow: 15m3/h
Head: 80m
Power: 7.5kw
Material: cast iron
Medium: clean water
Outlet dia: 50mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
Flow: 20m3/h
Head: 30m
Power: 3kw
Material: cast iron
Medium: clean water
Outlet dia: 60mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
Flow: 20m3/h
Head: 40m
Power: 4kw
Material: cast iron
Medium: clean water
Outlet dia: 60mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
Flow: 20m3/h
Head: 54m
Power: 5.5kw
Material: cast iron
Medium: clean water
Outlet dia: 60mm
Diameter: 175mm
Speed: 2850r/min
Voltage: 380V
Phase: 3 phase/50Hz
Color: Blue
QJ Submersible pumps Parameters:
Flow range10~500m3/h, Lift scope within 5~405m;
Caliber scope 32~203mm, Temperature range-15~80° C.
Products Overview:
QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
QJ Submersible pumps use conditions
1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply.
2. Electrical cavity must be filled with water.
3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m.
4. Electrical from the bottom of the bottom of the well shall be not less than 3 m.
5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C.
6. Water and sand content (by mass) of not more than 0.01%.
7. Water PH 6.5-8.5.
8. The hydrogen sulfide in water content is not more than 1.5 mg / L.
Application :
deep well water
farm irrigation
sprinkling irrigation
urban and rural industry
mine supply and drainage.
P31:pressures to 3000 psi. Flows to 41 gpm high tensile grey iron, designed for high-torque applications with unique pressure balanced thrust plates that comtribute to optimized performance.
P51:pressures to 3000 psi. Flows to 66 gpm high tensile grey iron construction, designed for high-torque applications with unique pressure balanced thrust plates that comtribute to optimized performance.
P76:pressures to 3000 psi. Flows to 128 gpm high tensile grey iron construction, designed for high-torque applications with unique pressure balanced thrust plates that comtribute to optimized performance.
Roller bearing pumps include models 020, 031, 051 and 076
Features:
Pressure balanced thrust plates
Durable high-strength cast iron body
Contamination tolerant
Volumetric efficiencies to 95%
Applications:
Material handling
Turf care
Agricultural
Construction equipment
Valve options:
Pressure relief valve
Load sense unloading bolt-on relief valve
Priority flow divider
Trade names: cast iron roller bearing pumps are also marketed under the commercial brand name.
Sqj submersible pumps parameters:
Flow range10~500m3/h, lift scope within 5~405m;
Caliber scope 32~203mm, temperature range-15~80° c.
Products overview
Sqj series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions
1. Sqj submersible pumps use conditions:
(1)380 v bias voltage does not exceed +/-10% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply.
(2) Electrical cavity must be filled with water during operation.
(3)the first-class pump impeller should at least go into a dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m in depth.
(4)the normal water temperature should be no higher than 20 ° c, qjr- hot water pump temperature up to 80 ° c.
(5)water and sand content (by mass) of not more than 0.01%.
(6)water ph 6.5-8.5.
(7)the hydrogen sulfide in water content is not more than 1.5 mg / l.
Products overview
Sqj, sqs, sqy, series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation.
Product use conditions:
1.380 v bias voltage does not exceed +/-10% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply.
2.Electrical cavity must be filled with water during operation.
3.The first-class pump impeller should at least go into a dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m in depth.
4.The normal water temperature should be no higher than 20 ° c, qjr- hot water pump temperature up to 80 ° c.
5.Water and sand content (by mass) of not more than 0.01%.
6.Water ph 6.5-8.5.
7.The hydrogen sulfide in water content is not more than 1.5 mg / l.
Submersible deep well pumps
Sqj , sqs, sqy submersible pump series parameters
Sqj submersible pumps parameters:
Flow range10~500m3/h, lift scope within 5~405m;
Caliber scope 32~203mm, temperature range-15~80° c.
Sqs bearing submersible pumps parameters:
Flow range10~250m3/h, lift scope within 5~12m;
Caliber scope 30~150mm, temperature range
Flow: 10~500m3/h
Lift: 15~405m
Caliber: ?175~?400mm
Power: 0.4-160kw
Temperature: =140 ?
Qualitycertificate: one year warranty and lifelong maintenance
Qjr submersible hot water pump overview:
This machine is used to deliver water. It has submersible motor and works under water. It is mainly used for farmland irrigation, water supply and water drainage in cities, factories and mines.
Qjr series spring pump is widely used in special occasions like heating for warmth, physiotherapy, health care, earth energy utilization, etc. Its motor and pump are united into one. Its structure is simple, easy to install and disassemble, taking little floor space. It is easy to use and maintain, works safely and reliably, causing no pollution to water source.
Qjr submersible hot water pump application range:
1. To collect hot water from boilers for secondary use
2. To collect water that leaks from heating pipelines in winter for secondary use
3. To collect cooling water in factories for secondary use (the pump should be submerged in water when working)
4. To deliver high temperature water through heat-supply system
5. To be used for heat-supply equipment maintenance
6. To supply hot water for bath center
7. To draw water from underground hotsprings, etc.
Application:
This product is suitable voltage level is less than 3kv/6kv of electric submersible pump until and the power cable connected to the supporting power supply.
Operating characteristics:
Cables rated voltage:1.8/3kv---3.6/6kv
Cable minimum ambient temperature of not less than-50celsius degree.
Cable normal operating temperature between 90--250celsius degree
Cable minimum bending radius of not less than 30 times the thickness of cable.
The structure of cable includes conductor, insulation, Kapton, lead sheath layer and armor.
The production range of cable :the cross-sectional area is 10--20mm2 and the core number is 3.
Type: hydraulic vane pump
Model Number: VP-SF-15-D (VP-15-FA3)
Brand Name: JUN LING
Place of Origin: Guangdong, China (Mainland)
pressure range: 50--70 bar (kgf/cm2)
displacement: 15 L/min
shaft key: parallel key or spline shaft
shaft diameter: 12.70 mm or 15.875mm
flange size:: 82.55 mm
parallel key spec.: 25mm length, 3.18mm
width sauction port diameter: 1/2 "
delivery port diameter: 3/8"
drain port diameter: 1/4"
weight: 5 kg
Type: hydraulic vane pump
Model Number: VP-SF-15-D (VP-15-FA3)
Brand Name: JUN LING
Place of Origin: Guangdong, China (Mainland)
pressure range: 50--70 bar (kgf/cm2)
displacement: 15 L/min
shaft key: parallel key or spline shaft
shaft diameter: 12.70 mm or 15.875mm
flange size:: 82.55 mm
parallel key spec.: 25mm length, 3.18mm
width sauction port diameter: 1/2 "
delivery port diameter: 3/8"
drain port diameter: 1/4"
weight: 5 kg
C101/102 series pumps have operating pressures up to 172 bar (2, 500 psi) and speeds up to 4, 000 rpm. Pressure balanced thrust plates assure maximum efficiency under all operating conditions, contamination tolerant.
Our dump body truck pumps products deliver the right flow range for most applications at 1800 rpm/2000 psi. Models with two shafts (c101) can be mounted to remote pto’s operating in either direction of rotation. Single shaft units (c102) mount directly to the vehicle drive train. These models can be connected in 2 or 3 line circuits to control single-acting cylinders. Offers reliable performance, pressure balanced thrust plates assure maximum efficiency under all operating conditions, contamination tolerant, serviceability/repeatability. All units are supplied with factory-set 2000 psi relief valves.
5792 Industrial Pumps Suppliers
Short on time? Let Industrial Pumps sellers contact you.
