Electric fire pump is a kind of water supply device widely used in hospitals, shopping malls, office buildings and residential buildings in the middle and high-rise buildings, when an accidental fire, start the fire pump can ensure that the water pressure in the pipe network to meet the requirements of the fire extinguishing device, so that the fire is timely put out. In China, the fixed electric fire pump water supply system generally adopts the mode of one (or more) main pump with one (or more) standby pump, and is equipped with a special control cabinet to achieve the control of the fire pump.
Pump 21N-60-34100 Pump 708-2H-00440 Pump 706-7L-01111
Good quality 500W BLDC water pump controller Rated power : 500W Rated input:AC220W Input range : AC170-276V RPMï¼?200-6000RPM Control way: Sin wave control, FOC Hall sensor: Senseless Speed control: VSP Protection function Current limit protection, Over current protection, Under voltage protection, Over voltage protection, Phase loss protection, Anti-lock protection, Empty load protection
Rated power:48W Rated input:DC24V Input range: DC 16-30V RPM:200-6000RPM Control way: Sin wave control, FOC Hall sensor:Senseless Speed control:VSP Protection:Current limit protection, Over current protection, Under voltage protection, Over voltage protection, Phase loss protection, Anti-lock protection, Empty load protection
UL/FM Approved 1000 Gallons Per Minute FIRE PUMP SYSTEM, 10 Bar, Product : UL/FM Approved 1000 GPM FIRE PUMP SYSTEM Brand : SFFECO (SAUDI FACTORY FOR FIRE EQUIPMENT CO.) Condition : Brand New YOM : 2023 Location : EXSTOCK, UAE. â?¢ Price is inclusive for : o Electric Pump Code SF-PMPULHESELEC092 â?? 1 SET o Diesel Pump Code SF-PMPULHESDIES092 -1 SET o Jockey Pump Code SF-PMPJOCKEY50HZ07 -1 SET o Electric Pump Controller Code SF-PMPCPGPY50HZ11 -1 SET o Diesel Pump Controller Code SF-PMPCPGPD02 -1 SET o Jockey Pump Controller Code SF-PMPCPJP350HZ04 -1 SET o Diesel tank Code SF-TANKDIESNONUL03 -1 SET o Battery Code SF-PMPBAT150AH03 -4 SET o Terminal Box SF-PMPST431 -1 SET o Flow Meter Code SF-VLVFM008 -1 SET o Pressure Relief Valve Code SF-PMPACCPRV02 -1* SET o Waste Cone Code SF-WCFLG004 -1* SET ITEM DESCRIPTION QTY COUNTRY OF ORIGIN SFFECO-UL/FM APPROVED END SUCTION (SFP 1000-54 EM-2G) ELECTRIC MOTOR DRIVEN SKID PUMP 1000 GPM @ 10 BAR COUPLED WITH UL LISTED ODP MOTOR. SUCTION AND DISCHARGE PRESSURE GAUGES, AND CASING RELIEF VALVE ARE INCLUDED. 1 UAE SFFECO-UL/FM APPROVED END SUCTION (SFP 1000-54 EM-2G) ENGINE DRIVEN SKID PUMP 1000 GPM @ 10 BAR COUPLED WITH UL/FM LISTED STALLION ENGINE. SUCTION AND DISCHARGE PRESSURE GAUGES ARE INCLUDED. 1 UAE GMAX PUMP VERTICAL MULTISTAGE JOCKEY 5.5HP, 2900 RPM, 380/415V, 50HZ, GMAX MODEL GVR 8-120 WITH BASE INCLUDED. 1 UAE CONTROL PANEL WITH NEMA2 ENCL. FOR ELECTRIC PUMP STAR DELTA OPEN STARTER MODEL GPY-125HP-50HZ-380/415V-3PH, TORNATECH. UL&FM APPROVED. 1 UAE CONTROL PANEL WITH NEMA2 ENCL. FOR DIESEL PUMP MODEL GPD-24-220 TORNATECH. UL&FM APPROVED. 1 UAE CONTROL PANEL WITH NEMA2 ENCL. FOR JOCKEY PUMP DOL STARTER MODEL JP3-5.5HP-50HZ-380/415V-3PH, TORNATECH. UL APPROVED. 1 UAE SFFECO TANK DIESEL 150 GALLON CAPACITY CYLINDRICAL SINGLE WALL FACTORY STANDARD 1 UAE BATTERY FOR DIESEL ENGINE DRIVEN PUMP FOR ENGINE CAPACITY 80HP AND ABOVE 4 KOREA TERMINAL BOX 60-125 HP FIRE PUMP 1 UAE FIRE PUMP FLOW METER SIZE 6" FM APPROVED FOR 1000 GPM TO 1250 GPM & BELOW 1 USA
Equivalent Andritz S pump spare parts including: Impeller (2 vanes, 3 vanes, 6 vanes, 8 vanes), Volute Casing, Casing Cover, Front Lining, Rear Lining, Stuffing Box Body, Shaft Wear Sleeve etc which for Andritz S series paper-pulp pumps. Paper Stock Pulp Pumps and Wearing Spares working advantages: 1. High efficiency and energy saving: The operating efficiency is 3-10 percentage points higher than that of ordinary pulp pumps on average, and the energy saving and consumption reduction reach 15-30%. 2. Good cavitation performance and long service life: the actual service life can be 2-3 times longer than that of ordinary pulp pumps; 3. High concentration and no clogging: the pulp concentration can reach 6%; 4. Reasonable structure and convenient maintenance: The pump head part adopts a front and rear door-opening structure. There is no need to disassemble the pipeline during maintenance. The pump can be disassembled and repaired by simply moving the motor backward.
SP/SPR heavy duty cantilever sump pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. Vertical Sump Slurry Pumps Spare Parts Design features: â?¢ Fully Cantilevered - Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. â?¢ Impellers - Unique double suction impellers; fluid flow enters the top as well as the bottom. This design eliminates shaft seals and reduces thrust load on the bearings. â?¢ Large Particle - Large particle impellers are also available and enable passing unusually large solids. â?¢ Bearing Assembly - The maintenance friendly bearing assembly has heavy duty roller bearings, robust housings, and a massive shaft. â?¢ Casing - The metal pumps have a heavy walled abrasive resistant Cr27Mo chrome alloy casing. Rubber pumps have a molded rubber casing adhered to sturdy metal structures. â?¢ Column and Discharge Pipe - The metal pump columns and discharge pipes are steel, and the rubber columns and discharge pipes are rubber covered. â?¢ Upper Strainers - Snap in elastomer strainers fit in column openings to prevent overly large particles and unwanted refuse from entering casing of the pump. â?¢ Lower Strainers - Bolt-on cast strainers on the metal pump and molded snap-on elastomer strainers on the rubber pumps protect the pump from oversize particles.
1.5/1B-AH Slurry Pump is end-suction, split-case, centrifugal slurry pumps have set the world standard for heavy duty abrasive pumping applications. With large shaft diameters, heavy duty bearing assemblies and robust slurry pumping capacity, Application customization comes standard with this line by applying a wide variety of metallic and elastomeric parts options, an assortment of seal arrangements, and a standard impeller adjustment mechanism incorporated into every base assembly. Tobee�® AH Series Slurry Pumps are the most comprehensive range of centrifugal slurry pumps for use in mining, minerals processing, coal preparation, dredging, metallurgy, power plant, chemical and general industry applications. The wetted parts materials designed by High abrasion and corrosion resistance alloy, rubber or polyurethane etc, Expecially for handling high abrasive, high density slurries.
3/2D-HH High Head Slurry Pump is designed to produce high heads per stage at high pressures. Commonly used for long distance transport lines, the high head slurry pump lines can often satisfy application duties with a single pump where others require multiple pumps in series.
Tobee E044 Split Packing Gland Assembly is used for 6x4 EAH slurry pump, 8x6 EAH slurry pump and 10x8 EM slurry pump. Slurry Pump Gland Assembly is primarily used to compress the packing to ensure a tight seal between the packing and the bushing. Gland Assembly has a split Gland Assembly that is typically used in slurry pumps.
Tobee C090 Slurry Pump Shaft Seal is been called slurry pump shaft seal ring, Double Lip Seal as well, which is a kinds of seals spare parts of 1.5/1C-HH, 3/2C-AH Slurry Pumps, 4/3C-AH, 4/3C-SC, 75C-L Slurry pumps. Slurry Pump Intake Joint is used for sealing the pump with inlet pipeline or inlet valve for preventing leak from suction end, It is installed on slurry pump suction flange.
32056RU Impeller of 3 vanes for 3x2 C-SC series rubber lined slurry pumps, which are suited for processing the chemical acid slurries. Tobee�® Provides replacement SC and L series pump wet parts that are able to be interchangeable. Both types smaller pumps with Semi-open impellers. The material of the wet parts can be used as A05, A07, A33, A49, A51, A61, and natural rubber spares. Today we are talking about the A49 Alloy and rubber spares. They have the same function to prevent erosion and corrosion.
Spare Parts for 65QV-SP, 100RV-SP, 150SV-SP Vertical Slurry Pumps. Mainly SP Metal Lined Vertical Sump Pump Parts: Impeller - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary. Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. Column Assembly - Completely fabricated from mild steel. G refers to submerged depth 1200mm; J refers to submerged depth 1500mm; L refers to submerged depth 1800mm; M refers to submerged depth 2000mm; Q refers to submerged depth 2400mm; Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR. Upper Strainer - Snap in elastomer strainers fit in column openings to prevent overly large particles and unwanted refuse from entering casing of the pump. Lower Strainer - Bolt-on cast strainers on the metal pump and molded snap-on elastomer strainers on the rubber pumps protect the pump from oversize particles. Discharge Pipe - Metal for SP, elastomer covered for SPR. All wetted metal parts are completely rust protected. Fully Cantilevered - Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. Agitation - An external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye. Materials - Pumps can be manufactured in abrasive and corrosive resistant materials.
150SV-SP Vertical Slurry Pump is available in a wide range of popular sizes to suit most pumping applications. Thousands of these pumps are proving their reliability and efficiency worldwide in Minerals processing, Coal preparation, Chemical processing, Effluent handling, Sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation.
Tobee Andritz Pump Spare Parts namely the pump parts have direct connection with slurry, are very crucial to the service life of slurry pumps. The wet parts, include impeller, liner, throatbush, frame plate liner insert, casing, etc., are very easily worn-out components because they work under longtime impact of abrassive and corrosive slurries in the high speed. For the long service life of pump parts, the material plays an important role. Tobee�® mainly manufacture Andritz Paper Pulp Pumps and Spares Parts, such as Andritz ACP, S, CP, VP, FP etc paper pulp pumps and Andritz Spares Parts. Andritz replacement parts including: Open or Semi Impellers(2 vanes, 3 vanes, 6 vanes, 8 vanes), Pump casings, Casing cover, Front linings, Rear lininings, Stuffing box body, Shaft etc, The materials can be manufactured in cast iron, SS304L, SS316L, 1.4460 Duplex stainless steel, 1.4517, 1.4517 hardened etc. ANDRITZ S & ACP Series Centrifugal Paper Pulp Pumps are available with closed, semi-open or open impellers with 3 vanes or 6vanes in a highly wear-resistant design. These pumps are suitable for conveying many different media. Depending on the impeller design, they can convey slightly contaminated and contaminated media with some solids and content up to consistencies up to 8%. S series and ACP series paper pulp pumps are wide used in the pulp and paper, mining, offshore, power, food, and chemical industry. Additionally, water supply, waste water treatment, desalination plants, and irrigation as well as drainage etc.
135.2 Rear Liner is one of wear parts for Andritz S series Pump S125-400 DD. The Rear Liner 135.2 suitable for Andritz S Series, the model: S 80-265, S 100-265, S 125-265, S 100-350, S 125-350, S150-330, S125-400, S 150-400, S 200-380, S 150-470, S 200-470, S 250-430, S 350-470, S 500-600, S 600-700. Tobee�® manufacture a range of replacement parts including impellers(2 vanes, 3 vanes, 6 vanes, 8 vanes), casings, casing cover, front lining, rear lining, stuffing box body, shaft etc which for Andritz S series pumps, ACP series pumps, FP series pumps etc Tobee�® Pump is always making continuous optimization of materials like Cast steel, EPDM, Hypalon, Hastelloy, CD4MCu, Viton, Fluoroplastic, Ceramic, Bronze, Titanium, Aluminum and other anti-abrasive & corrosive materials for various applications. Such as impeller: EN-GJL 250, 1.4460 and 1.4517, casing/casing cover: EN-GJL 250 and 1.4460, volute casing: EN-GJL 250, EN-GJS-400-15 and 1.4460, bearing housing EN-GJL 250 and 1.4468, front and rear lining: 1.4460 and 1.4517, stuffing box body EN-GJL 250, 1.4460 and 1.4408, shaft: 1.4021 & 1.4462 and 1.4404 & 1.4439, etc. ANDRITZ S & ACP Series Centrifugal Paper Pulp Pumps are available with closed, semi-open or open impellers with 3 vanes or 6vanes in a highly wear-resistant design. These pumps are suitable for conveying many different media. Depending on the impeller design, they can convey slightly contaminated and contaminated media with some solids and content up to consistencies up to 8%. S series and ACP series paper pulp pumps are wide used in the pulp and paper, mining, offshore, power, food, and chemical industry. Additionally, water supply, waste water treatment, desalination plants, and irrigation as well as drainage etc. ANDRITZ FP Series Double Suction Fan Pump is a low pulse and high efficient paper pulp pump,It is new standards in terms of efficiency, flexibility, and design. This double-suction pump series was designed for flow rates up to 20,000 m�³/h and heads up to 220 m. The pumps can convey stock suspensions with consistencies of up to 2%. The fan pump supplied has a very high efficiency of 92% and lowest pulsation in order to guarantee perfect sheet formation.
Tobee Andman Paper Pulp Pumps SPECIFICATIONS: Size: 1"-16" Pump Capacity: 30-3300m3/hr Head: 3-100m Working temp.: 120 Concentration: 0%-7% Material:Cast iron, Cast steel, SS304, SS316L, Duplex stainless steel etc Design Features: Impeller - Adopting full open type impeller with large channel design by precision casting, No. of vanes is 3-6 vanes,This configuration can reduce the axial force, And in the transporting, it will not generate bubbles, non-clog impeller channel,Improving the pulp concentration. Volute casing - Adopting single stage vortex casing, big size, Casing is designed as duoble casing structure for reducing radial force and axis deviation. Materials - various mateials of Wetted parts are available, Such as Cast iron,SS304,SS316L,Duplex stainless steel etc Shaft seal - Mechanical seals and packing seal can be used as per requested Severe application - Excellently suited for transporting media containing solids (e.g. for pulp, paper, or effluent applications) Andritz S Series Pump Models and Spares: S80-265, S100-265, S125-265, S3 100-350.3, S125-350, S150-330, S3 125-400, S3 150-400.3, S3 200-380, S8 200-380, S3 150-470.3, S3 200-470.3, S3 250-430.3, S3 350-470.3, S8 350-470.6, S500-600, S600-700 etc. Andritz ACP Series Pump Models and Spares: ACP65-315, ACP100-500, ACP65-250, ACP100-315, ACP125-400, ACP150-500, ACP100-250, ACP125-315, ACP150-400, ACP200-500, ACP300-700, ACP125-250 etc.
Equivalent Andritz S100-265 Process Pumps and Paper Pulp Centrifugal Pumps are widely used for handling pulp and paper stock transfer. Tobee Andman Paper Pulp Pumps SPECIFICATIONS: Size: 1"-16" Pump Capacity: 30-3300m3/hr Head: 3-100m Working temp.: â?¤120â?? Concentration: 0%-7% Material:Cast iron, Cast steel, SS304, SS316L, Duplex stainless steel etc Design Features: â?¢ Impeller - Adopting full open type impeller with large channel design by precision casting, No. of vanes is 3-6 vanes,This configuration can reduce the axial force, And in the transporting, it will not generate bubbles, non-clog impeller channel,Improving the pulp concentration. â?¢ Volute casing - Adopting single stage vortex casing, big size, Casing is designed as duoble casing structure for reducing radial force and axis deviation. â?¢ Materials - various mateials of Wetted parts are available, Such as Cast iron,SS304,SS316L,Duplex stainless steel etc â?¢ Shaft seal - Mechanical seals and packing seal can be used as per requested â?¢ Severe application - Excellently suited for transporting media containing solids (e.g. for pulp, paper, or effluent applications) Andritz S Series Pump Models and Spares: S80-265, S100-265, S125-265, S3 100-350.3, S125-350, S150-330, S3 125-400, S3 150-400.3, S3 200-380, S8 200-380, S3 150-470.3, S3 200-470.3, S3 250-430.3, S3 350-470.3, S8 350-470.6, S500-600, S600-700 etc.
Tobee S Series Pumps and Pump Spares are widely used in papermaking, pulp mills, pulp medium of transportation, also applies to enterprise sugar, starchprocessing, chemical raw materials, such as the transmission medium. Tobee S Paper Stock Pulp Pump SPECIFICATIONS: Size: 1"-16" Pump Capacity: 30-3300m3/hr Head: 3-100m Working temp.: 120 Concentration: 0%-7% Material:Cast iron, Cast steel, SS304, SS316L, Duplex stainless steel etc Andritz S pump spare parts including: Impeller (2 vanes, 3 vanes, 6 vanes, 8 vanes), Volute Casing, Casing Cover, Front Lining, Rear Lining, Stuffing Box Body, Shaft Wear Sleeve etc which for Andritz S series paper-pulp pumps.
Tobee manufactures Andritz alternative ACP, S, VP, FP, CP series Paper & Pulp Stock Pumps and Pumps Wearing Spares, all the pumps and spares parts are widely for Paper mills, Paper Pulp, Coal prep, Waste pulp, Paper stock, Paper making, Waste paper stock, Chemical slurries, Sugar refining, Recycled fiber preparation, Chemical industry, Food industry, Energy supply, Water supply, Waste water treatment, Alkali recovery, Sugar syrup, Molasses, Pharmaceuticals industry, Potash Fertilizer Plant, Other industries etc. Andritz S pump spare parts including: Impeller (2 vanes, 3 vanes, 6 vanes, 8 vanes), Volute Casing, Casing Cover, Front Lining, Rear Lining, Stuffing Box Body, Shaft Wear Sleeve etc which for Andritz S series paper-pulp pumps. Andritz S Pump Models and Spares: S80-265, S100-265, S125-265, S3 100-350.3, S125-350, S150-330, S3 125-400, S3 150-400.3, S3 200-380, S8 200-380, S3 150-470.3, S3 200-470.3, S3 250-430.3, S3 350-470.3, S8 350-470.6, S500-600, etc
