Bleached Softwood Pulp is commonly used in the production of most paper, paperboard and tissue products. Softwood pulp brings strength to the end product, as well as runnability and excellent dewatering properties to the production process.
virgin polyester staple fiber 1.2-1.4d 38mm psf fiber Application: 1. yarn spinning, open end spinning and ring spinning, sock yarn, mop yarn 2. needle punch nonwoven, for geotextile, automotive interior, exhibition carpet, trunk nonwoven, insulation panels.
Cottonseed oil, like all oils extracted from plants, is cholesterol-free, making it an excellent alternative for people looking to lower their cholesterol levels. Because it is not as heavy as other oils, it is used for baking. It has a high level of oxidation resistance, making it perfect for salad dressings. Cottonseed oil has long been used as a frying oil because of its low cost, and it is one of the best frying oils for the ready-to-eat snack food sector. Cotton seed, like other oilseeds such as sunflower seed, has an oil-bearing kernel encased by a hard outer hull; the oil is removed from the kernel during processing. Salad dressings are made with cottonseed oil.Cotton seed, like other oilseeds such as sunflower seed, has an oil-bearing kernel encased by a hard outer hull; the oil is removed from the kernel during processing
Sodium chlorate is an inorganic compound with the chemical formula NaClO3. It is a white crystalline powder that is readily soluble in water. It is hygroscopic. It decomposes above 300 C to release oxygen and leaves sodium chloride. Several hundred million tons are produced annually, mainly for applications in bleaching pulp to produce high brightness paper. The main commercial use for sodium chlorate is for making chlorine dioxide (ClO2). The largest application of ClO2, which accounts for about 95% of the use of chlorate, is in bleaching of pulp. All other, less important chlorates are derived from sodium chlorate, usually by salt metathesis with the corresponding chloride. All perchlorate compounds are produced industrially by the oxidation of solutions of sodium chlorate by electrolysis.
Making wadding and padding materials 7D*64mm HC non silicon polyester staple fiber white color 054310599 Our siliconized fiber mainly can be used in home textile, such as filling sofa, pillow, cushion and winter clothing and non siliconized mainly can be used in non woven fabrics, such as padding, mattress and wadding.
Product Introduction PET spunbond substrate fabric compared with short fiber polyester tire has high tensile strength, elongation, stability, aging resistance, long service life, good wettability and other characteristics, as the internationally recognized high-performance SBS, APP and other modified asphalt waterproof roll tire. Application Area Modified asphalt waterproof coil is widely used in waterproof concrete building, such as building roof, underground structure, high-speed railway, tunnel, highway and railway bridge waterproof field.
What is pe/pp bicomponent fiber? PE/PP bicomponent fiber is a type of synthetic fiber that is made up of two different polymers, polyethylene (PE) and polypropylene (PP), which are combined in a single filament. What are the advantages of using PE/PP bicomponent fiber in textiles? PE/PP bicomponent fiber offers several advantages in textiles, including improved strength, durability, and moisture management. It also provides a softer feel and can be used in a variety of applications, such as sportswear, outdoor apparel, and home textiles. What are some common uses of PE/PP bicomponent fiber in the textile industry? PE/PP bicomponent fibers have several advantages that make them popular in the textile industry. Some of these advantages include: Improved Strength: PE/PP bicomponent fibers have a higher tensile strength than regular fibers, making them ideal for use in high-stress applications. Enhanced Durability: These fibers are resistant to wear and tear, making them ideal for use in products that need to withstand daily use. Improved Comfort: PE/PP bicomponent fibers have a soft texture, which makes them comfortable to wear against the skin. Moisture Management: These fibers are hydrophobic, which means they repel water and moisture. This property makes them ideal for use in products that need to stay dry. Some common uses of PE/PP bicomponent fiber in the textile industry include: Clothing: These fibers are often used in the production of sportswear, outdoor clothing, and other products that require enhanced durability and moisture management. Home Textiles: PE/PP bicomponent fibers are used in the production of carpets, curtains, and other home textiles that require enhanced strength and durability. Nonwoven Fabrics: These fibers are used in the production of nonwoven fabrics, which are used in a wide range of applications, including medical products, hygiene products, and filtration materials. Overall, PE/PP bicomponent fibers offer several advantages that make them a popular choice in the textile industry for a wide range of applications.
Fibre Fill Polyester Filling Microfiber Fiber 0.9d Down Like Virgin Micro Gel Fiber Hot Sale Virgin Down Like Polyester Fiber filling fiber hollow conjugated fibers recycled polyester stuffing fiber 1) Denier:0.8D-1.5D 2) Cut length:22MM/25MM/32MM/38MM/51MM/64MM/71MM/76MM 3) Luster:raw white Virgin and recycled grade 4) Siliconized and no siliconized 5) Merits: high intension, stable stretch elongation, highly elastic, puffed, high ratio of hollowness 6)Excellent fluffy performance, pleasing hand feeling, plump, gentle, luster 7) Usage: suitable for filling toys, pillows, cushions, and other products need to be filled ; make pearl cotton. bedclothes , man-made fur, filler materials, sofa and others 8) Weight: around 300kgs/bale 9) Package: woven bag Container load: around 34 bales for a 20GP,around80 balesfor a 40HQ 10) Delivery Time: within 15 days after receiving the deposit
New-type hot-connectivity composite fiber is made from different types of modified high molecular materials through advanced composite spining technology. It has unique characteristic of melting at low temperature, and after hot treatment, it can naturally adhere without use of binder, green and environmental. The product abides by strict sanitation control standards to achieve sanitation material grade. The products include ES fiber and ETS modified polyester composite staple fiber which is initiated by the company, and can be applied to production of surface layer and guide layer of disposable sanitary articles Functional characteristic the product is a kind of chemical blend provided with advantages of the two materials. ES fiber has low melting point on the superficial layer, soft, bouffant and pervious, while the core layer has certain intensity and fiber state. ETS fiber is provided with advantages of heat bonding, high hygroscopicity and antistatic property, etc. Application scope the sanitary products are applicable to hot air penetrating technology to produce surface layer and guide layer of disposable sanitary materials such as paper diaper and sanitary towel; the conventional low-melting fiber is applicable to production of hard cotton, decorative wall board, environmental mattress, seat mat, environmental filter media, constructional acoustic damping and heat insulation materials, etc. Specification 4D*51MMã??4D*32MM
The polyester staple fiber machine (PSF plant) takes virgin PET Chips, recycled Bottle Flakes, Popcorn and Lumps, etc., as raw material, with continuous drying (or batch drying through Vacuum Dryer), high pressure melt spinning process engineering and VFD controlled Spinning & Stretching process engineering to produce normal Staple Fibre, High Tenacity Low Elongation Staple Fibre and Hollow Fibre. Single plant capacity is 15T.P.D. to 80T.P.D. Equipment Technical Data Titer Range dtex 6.67-16.67 Spinning Pos. nos. 6-24 Spinning Pitch mm 700, 750 Plant Capacity TPD 15-80 Spinneret dia. mm 328, 358, 410 Spinning Mechanical Speed m/min 500-1,500 Spinning Processing Speed m/min 500-1,300 Stretching Mechanical Speed m/min 240 Stretching Processing Speed m/min 230 Total Tow Titer at Stretching dtex 600,000-3,000,000 Stuffer Box Width mm 160-410 Cutting Length mm 25, 32, 38, 44, 51, 64, 76, 101 Bale Weight kg 200-350 Application: Cushions Pillows Quilts Toys Jacket Mattress Non woven carpet Automotive felts, speaker felts, geo textiles, polyfill wadding, filter fabrics and other acoustics as well. Spinning Line: Continuous Dryer Hopper Screw Extruder Polymer Pipe Filter Spin Beam (Meter Pump System, Spin Pack, Spinneret) Quenching Unit Interfloor Duct Draw-off Wall Capstan Roller Sunflower Gearing Unit Automatic Fiber Can Device Drawing line: Can Creel Inlet Thread Guide Tow Guide Stand Dipping Bath 1st Draw Stand Draw Bath 2nd Draw Stand Draw Steam Chest 3rd Draw Stand Tow Stacker Crimper Steam Box Crimper Silicone Oil Sprayer Machine Tow Tension Stand Cutter Fiber Spreading Machine Relaxer Fiber Blowing system Baling Press
ES fiber is a sheath-core composite fiber obtained by successfully combining low-melting components and high-melting components on a single fiber. It has excellent thermal bonding properties. The low melting point component in ES fiber melts under heat treatment conditions higher than its melting point, and bond with other materials to form a binder-free environmentally and friendly non-woven fabric. ES fiber has various advantages such as soft, fluffy, low-temperature processing, heat-bonding, plasticity, non-toxic, non-irritating, and lightweight. It is mainly used to manufacture high-quality sanitary products such as sanitary napkins and diapers. And it is also high-quality materials used to make medical products such as medical protective cloth and medical protective masks, and so on. There are two main types of ES fibers. The first kind is a composite of PE and PP. Its sheath layer is PE (polyethylene, melting point 130�°C), and its core layer is PP (polypropylene, melting point 165�°C). The second kind is a composite of PE and PE. Its sheath layer is PE, and the core layer is PET (polyester, melting point 255â??), which is an upgraded version of PE/PP. ES is divided into EP and ET in terms of material and functionally divided into the hydrophilic, water-repellent, hydrophilic, and weak parent, single parent, multi-parent.In addition, it also can be divided into whitening, general whitening, high holding, medium holding, and low holding. The specifications are 1.5D38mm, 2D38mm, 4D51mm, and so on. In the future, the trend will gradually develop towards fine deniers. SPECIFICATION: PE+PET ES Fiber: Optical White & Super Hydrophile 2D*38mm, Optical White & Hydrophile 2D*38mmï¼? Optical White & Water Repellency 2D*38mmï¼? RAW White & Water Repellency 2D*38mmï¼? Optical White & Super Hydrophile 1.5D*38mmï¼? Optical White & Water Repellency 1.5D*38mmï¼? RAW White & Water Repellency 1.5D*38mï¼? Hydrophile 2D*38mmï¼? Water Repellency 2D*38mm PE+PP ES Fiber: Hydrophile (P2Q) 2D*38mm
This type Chips that is designed to resist burning and melting at low temperatures. Low Melting Point Polyester Chip for Hot Melt Yarn Masterbatch Extrusion Grade Polymer for Hot-melt Adhesive Glue Coating Description: Generally speaking, the low melting point polyester chip refers to one specialty polymer with a melting point between 90 and 220. The melting point of polyester is the temperature at which a solid crystalline substance changes from a solid state to a liquid. So it reflects the purity of polyester. Generally speaking, pure polyester is a partially crystalline polymer with a melting point of 265. But during actual production, some impurities exist in the polyester due to various side reactions. At the same time, the defects of polymer crystals and the difference in crystallinity will also affect the melting point. The common type of low melt polymer is 110. But we can also offer a melting point of 90, 120, 160, and 180. Application: Low-melt polyester chips can produce low-melting point fiber, low-melting point synthetic fiber, and thermal-melting mucilage. Its primary usage is acting as bonding fiber in nonwoven fabrics. The end usage lies in clothing, articles for bed, shoe uppers, sleeping bags, sofas, and hygiene products. LM PET Chip is also the main raw material of masterbatch carriers. That is, low-melt PET chips, conventional chips, and dyes are mixed to produce the polyester color masterbatch according to a certain proportion. The production of this product is the introduction of polyester macromolecules into the modified copolymer unit. And its melting point is in the range of 100-120. Commonly used modifiers are phthalic acid, adipic acid, and trimethylolpropane. Recently, LM Polymer is also extruded into the back coating of nonwoven, automotive interiors, foam, injection molding, PET sheets, and hot-melt adhesive/glue. Low Melt Yarn is also called hot melt yarn or fusible yarn. There are sheath-core low-melt bicomponent yarn and full low-melt polyester yarn.
Global Industries FZC is an established and renowned AluminiumFabrication company with wide experience in the construction and refurbishment sectors. We have a reputation for providing pro-activeadvice on practical and innovative solutions. By drawing on the experience gained from working on various projects, we provide a highquality, efficient and cost-effective service solution. Highly skilled labour, motivated staff guided by qualified management team ensures highest quality and effeciency to all the jobs we undertake.Our factory and facilities are fully equipped with the latesttechnology , machinery and tooling. Our Mission : Providing our customers with the highest quality products and services to establish long-lasting relationship. We continually strive to exceed customer expectations and gain their confidence through theutilization of innovative products and latest technology. Our Vision : To be leaders in providing value added construction services to ourcustomers by creating successful partnerships with them throughout the construction process and achieve unhindered growth.
Pre fabricate cabin for construction sites .
Dyed BCI organic cotton yarn for socks.
Dust&Ammonia free and color and perfumed as per request. 25kg-50kg drums.
Bleach For Cleaning Is Available.
Prefabricated Buildings (Portacabins) Prefabricated Houses (Portacabins) manufactured by Global Industries FZC are the ultimate, versatile, sustainable building. Our modular system enable us to create buildings of any size with multiple storeys, for upto 1000 people or more. Our Prefabricated Buildings meet all permanent building standards. The difference is that, our buildings are fabricated in the factory, so that, quality can be precisely controlled and delivered to site for rapid installation. Our company legacy is grounded in its reputation for exceptional customer service, effective management of business operation and consistent product innovation. Our global presence combined with local market expertise provides exemplary service tailored to meet the unique needs of customers throughout the world. Our buildings are inherently energy efficient and able to achieve high levels of air tightness and thermal insulation properties. Application, could be any of the following : Site Accommodation Site Officces Emergency Accommodation Health Centers Classrooms Canteens Gate Houses Gymnasiums Hospitality Suites Training Rooms Document Storage Toilet Blocks First Aid Posts Catering Units Prayer Rooms Laboratories
Oilfield Accommodation & Utility Buildings Global Industies FZC is a leading provider of Modular Buildings for Workforce Housing and Camp Systems. We proudly serve a diverse range of industries and sectors, with an unmatched ability to design and completely customize workforce solutions. Our Camp System can be configured and scaled to accommodate crews and labour forces from 10 to 5000 people. We understand, companies operating in remote areas need on-site services and high end levels of accommodation to attract and retain workers. Companies wanting to provide their Workers with hotel-like services including catering, housekeeping, laundry and access to recreation activities and facilities, with a goal of creating a "home away from home" experience can rely on us. Our dedicated team will work with your Project Management Team every step of the way, from initial planning, designing, logistics and site installation. Application, could be any of the following : Worker Dormitories Staff Quarters Executive Dormitories Fitness Centers Gymnasiums Game Rooms Movie Theaters Commissary Dining Room Food Storage Food Preparation Room Shower & Toilet Clinics Laundry Offices Security Rooms
Building materials, food stuffs, textiles fabric like cotton, petroleum product.Exports, import
