Walk Behind Roller Description --------------- Value Working weight --------------- 180kg Working width --------------- 560 mm Actual load --------------- 2.9 kg/cm Walking speed --------------- 1.6 km/hr Frequency --------------- 4620/rpm Centrifugal Force --------------- 10 km Engine --------------- G X 160 5.5hp (Petrol)
Hardness is 58-62 HRC
Material is 30Mn Iron case
Material is Hi-Mn13-3 Iron case
JKY60/60-3.8 JKY55/55-3.8 JKY50/50-3.8 JKB55/55-3.0 JKB50/50-3.0 JKR45/45-2.0 JKR40/40-2.0 JKR35/35-1.5 Production capacity (standard brick packs/h) 13000-15000 11000-13000 10000-12000 12000-14000 11000-13000 12000-14000 9000-12000 8000-11000 Reamer diameter (mm) 600 550 500 550 500 450 400 350 Extruding pressure(MPA) 3.8 3.8 3.8 3.0 3.0 2.0 2.0 1.0-2.0 Forming liquid water content (%) 14~16 14~16 14~16 16~18 16~18 18~22 18~22 18~22 Vacuum (MPA) í_-0.092 í_-0.092 í_-0.092 í_-0.092 í_-0.092 í_-0.092 í_-0.092 í_-0.092 Power (KW) 75/200 75/160 55/132 55/132 55/110 45/90 45/75 37/55 The JKY modelíóJKB modelíóJKR model are advanced twin-stage vacuum Brick Presses which draw lessons from the developed domestic, abroad experiences and design to make .They are mainly made of high quality steel with features of reasonable structure, sturdy and durability. And they have strong applicability, high efficiency, easy maintenance but lower energy consumption. They are applicable for the production of high-rate hollow bricks with the materials of coal gangue, shale, high-volume fly-ash, urban construction waste, gangue waste, inferior soil.
Functional process: Load the material for grinding evenly and continuously into the grinding chamber of the main frame. Due to the centrifugal force in rotation, the roller swings outward and presses closely upon the ring. The shovel carries the material to the space between the roller and ring. When the roller rolls, the material is thus ground. After being ground, the material is to be routed to the sorter along the wind belt of the blower and the coarse powder will be put back to the mill for regrinding. The fine powder flows into the cyclone collector together with airflow and is expelled from the discharge pipe as final product. In the grinding chamber, since the material may contain moisture to some extent, the heat generated during grinding makes the moisture evaporated; since the pipeline joints are not airtight, the external air is sucked in and the circulation air amount increases. In order to enable the mill to work under negative pressure, the increased airflow is guided to the deduster anew sequentially to the atmosphere after purification.
Ball mill Ball mill is an efficient tool for grinding many materials into fine powder. The Ball Mill is used to grind many kinds of mine and other materials, or to select the mine.2 It is widely used in building material, chemical industry, etc. There are two ways of grinding: the dry way and the wet way. It can be divided into tabular type and flowing type according to different expelling mine. To use the Ball Mill, the material to be ground is loaded into the Neoprene barrel that contains grinding media. As the barrel rotates, the material is crushed between the individual pieces of grinding media that mix and crush the product into fine powder over a period of several hours. Quite simply, the longer the Ball Mill runs, the finer the powder will be. Ultimate particle size depends entirely on how hard the material you're grinding is, and the time how long the Ball Mill runs. Our Ball Mills have been used to grind glass, powder food products, creat custom varnishes,make ceramic glaze, powder various chemicals, and make Black Powder.
The application of cone crusher: The py series cone crusher has been developed to crush high or medium hardness material , such as iron ore , copper ore, limestone, quartz, granite, and sand stones, ect. And it is used in metallurgical, construction, road building, chemical, silicate industries.The cone crusher has the advantage of reliable construction, high prod activity , easy adjustment and less cost in operation. The spring release system of crusher acts an overload protection system that allows tramp to pass through the crushing chamber without damage to the crusher, use dry oil, water, two kinds of sealed formation. Cone crusher made plaster stone and engine oil separated, assured reliable performance. The type of crushing chamber depend upon the size of feed and fineness of the crushed product. The standard type is applied to medium crushing, the medium type is applied to medium or fine crushing and the short head is applied to fine crushing. The main features of cone crusher: 1.The py series crushers crushes by the change of the gap in the crushing cavity .The gap is opened and closed by the gyration of main shaft, which is derived by motor through cone gears. 2.The py series cone crusher is of high reduction ratio, high performance, low power consumption, and uniform size products. It has been used in the secondary and tertiary crushing. 3.The cone crusher consists of body frame, transmission shaft, eccentric sleeve, cone bearing, breaking cone, supporting sleeve, adjusting sleeve, feeding part, spring, elastic coupling , lubrication part , electric part, ect.
PLC Control spare parts
Fully-auto main machine, plc control, one whole spare parts, PVC pallets. 7250mm*6000*3500MM
Fully-auto main main machine, semi-atuo production line, one whole sets spare parts.
For polishing granite tiles 1 Unit
Granite double blade edge cutting machine 1 Unit
For tiles & slabs polishing machines
Granite slabs polishing machine
Model:GW40Z Cut reinforcing steel bar diameter:6-40mm(a3 steel) 6-36mm(h screw thread steel) Cut reinforcing steel bar intension:
Model Jf-3 260l Jf-3 300l Jf-3 350l Outlet capacity 260l 300l 350l Productivity 6-10m3/h 8-12m3/h 10-14m3/h Power 2.2kw 3kw 3kw Weight 270kg 300kg 300kg Engine Electric Outer size(mm) 1700x970x1600 1800x1070x1600 1900x1070x1750
We are distributors for one of the most reputed super k-span machines which has integrated micro-processor, working in all terrains, a mobile factory at site. With the purchase of our machines, one can construct steel structure of over 1000 sq meters in a single day with 10-12 workers at the construction site. Easily operated and efficient. These buildings are completely insulated and fire proof by our k-13 spray on. We use an array of supporting machines which simplifies construction and helps in gaining more profits.
Suspended plaform Driven by ri-phase asynchronous moor, i consiss of body, elecromagneic moor, cenrifugal over-speed governor, gear or worm ransmission sysem, and rope holding sysem, ec.
Scaffolding H-frame (item code: ntc-142) Weight appx. 40 kg, rate-64$ Pipe size-48 od, height- 1mtr. Width-500mm, erossing-40 od Pipe thickness 3mm with painting nut bolt. Heavy duty prop.( item code: ntc- 155) (d) open 2.59/3.95 mtr Pipe thickness-3mm, weight-19kg, rate-35$ Prop sleeve propnut with painted complete set Adjustable base jack (pipe od 38mm)(item-150) Height-760mm long, thickness-4mm, weight-3.7kg rate-7$ Threading-610mm 150mm plane with galvanising.
