Flow: 10m3/h Head: 40m Power: 2.2kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380v Phase: 3 phase/50hz Color: blue Qj submersible pumps parameters: Flow range10~500m3/h, lift scope within 5~405m; Caliber scope 32~203mm, temperature range-15~80° c. Products overview: Qj series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: Qj submersible pumps use conditions 1. 380 v bias voltage does not exceed + -5% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° c, qjr-temperature hot water pump up to 80 ° c. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water ph 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / l. Application : Deep well water Farm irrigation Sprinkling irrigation Urban and rural industry Mine supply and drainage.
Flow: 10m3/h Head: 65m Power: 4kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380v Phase: 3 phase/50hz Color: blue Qj submersible pumps parameters: Flow range10~500m3/h, lift scope within 5~405m; Caliber scope 32~203mm, temperature range-15~80° c. Products overview: Qj series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: Qj submersible pumps use conditions 1. 380 v bias voltage does not exceed + -5% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° c, qjr-temperature hot water pump up to 80 ° c. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water ph 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / l. Application : Deep well water Farm irrigation Sprinkling irrigation Urban and rural industry Mine supply and drainage.
Flow: 10m3/h Head: 95m Power: 5.5kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380v Phase: 3 phase/50hz Color: blue Qj submersible pumps parameters: Flow range10~500m3/h, lift scope within 5~405m; Caliber scope 32~203mm, temperature range-15~80° c. Products overview: Qj series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: Qj submersible pumps use conditions 1. 380 v bias voltage does not exceed + -5% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° c, qjr-temperature hot water pump up to 80 ° c. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water ph 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / l. Application : Deep well water Farm irrigation Sprinkling irrigation Urban and rural industry Mine supply and drainage.
Model Series 5/a series 5/v series 5/w Pressure range 1.6~3 bar 70~80 kpa 2~3 bar Flow range 6~11 l/min 5~11 l/min 800~1200ml Power 6~ 16 w Dc voltage 6v 9v 12v 24v brushless Dimension 86*60*38mm Weight 286g Technology features 24 hours working under normal condition Oil-free Compact size, high negative pressure, high performance price ratio Maintenance free High weight Low noise level&vibration and lower power consumption Can be mounted in any plane Flow can be adjusted (customized) Adopt customized industrial raw material, it can work with long time in high or low temperature under harsh condition Application Electron&electric appliance, food industry (jucier, vacuum preservation etc) Medical (oxygenators, sputum suction devices, blood pressure meter) Digital printing equipment Lab equiment, chemical analysis Beauty equipment (cupping) Automation (parts adsorption)
Basically we are dealing with Centrifugal Pumps 1.Water Pumps-WP Operating Range Delivery Size:DN 32 to 150 mm Capacity:upto 550 m3/hr Head:upto 100m Temperature:upto 160° C Pressure:upto 16 bar Design: Horizontal, radial split, volute casing pumps according to DIN 24255 std. with closed impeller, end suction, top centre line discharge. Back pull out design enables to remove the rotor without disturbing the pipelines. Application: For handling clean or slightly turbid non-aggressive liquids. Suitable for pumping condensate, general water supply in agriculture, trade, and industries with favourable NPSH condition. Materials: Cast Iron and Bronze. 2.Chemical Process Pump Operating Range Delivery Size DN 25 to 200 mm Capacity:upto 700 m3/hr Head:upto 180m Temperature:upto 260° C Pressure:upto 26 bar Design: Horizontal, radial split, volute casing pumps according to ANSI B73-1 specifications with open impeller, end suction, top centre line discharge. Simple external axial adjustment for impeller wear. Back pull out design enables to remove the rotor without disturbing the pipelines. If a spacer coupling is used, the motor does not have to be removed from the base plate. Only four bearing beds cover the entire 32 models. This means that the shafts, sleeves, bearings, and bearing beds are identical in and interchangeable for a large number of pump sizes. Application: For handling all chemical process requirements like acids, alkalis, corrosive slurries, hydrocarbons etc. Suitable for all liquids with/without solids Materials: Graded cast iron / WCB/CF8/CF8M (SS-316)/317/317L/CD4MCU/Alloy - 20/Hastalloy - B/ Hastalloy - C etc., If you have any inquiry about particular product then feel free to Contact us. Email:info@impetix.com Web:www.impetix.com Skype:impturno Cell: +91 98792 020860 Export Quality
. .
QL-690 150bar 380v copper motor car cleaner Jiuzhou is a professional company in designing, manufacturing and selling high pressure plunger pump, high pressure washer and some other cleaning machines. Our company is willing to cooperate with all friends worldwide. Please feel free to contact us for more information. Other Features: 1) 10m high pressure hose. 2) Long usage life. 3) The motor drives the plunger pump directly. 4) It has the features of mordernly designed, compact structure, small size. 5) convenient to move, high pressure and efficiency, less heat. Application: This high pressure washer is mainly used in cleaning and maintenance of all kinds of motor vehicles, engineering vehicles, agricultural machinery.Also it can be used to disinfect and clean of playground, square, exterior walls, doors, windows, hotel, hospital, gym and livestock farm. Model No. QL-690 Motor type Three-phase capacitor motor Power Supply 380V/50HZ Max Pressure 15Mpa Working Pressure 1-15Mpa(Adjustable) Power 4Kw RPM 1450R/M Theoretical Flow Rate ¡¨¹ 15L/min Net weihgt 76kg Gross Weight 80kg Size 80¡¨¢35¡¨¢80cm Move Modes Lift or push
We have Wilden Pumps - Re Conditioned for Sale and we Do Export to Africa these Pumps hence if u have any Requirements then let me know 15KGS - WOODEN BOX
Open flow:1.6L/min max output pressure:0.8-1.0Mpa Electric current¡êo1A inlet pressure: 0.2Mpa 6 pieces a carton G.W:14.5kg N.W:13.5kg
1. Heating mode only, max water outlet temperature is 80¡æ 2. Copeland evi scroll compressor, lcd display controller 3. Installed outdoor (on outdoor wall or in yard or top of house) 4. Needn't electric heater back up 5. Refrigerant:r134a 6. Capacity: 7~24 kw Plywood wood box
Specification: 1, permanent magnet and continuous duty 2, self-priming so pump can be located above water tank 3, runs dry for extended periods of time without damage 4, hold excellent motor keep stable temperature of pump body Size: 11.3" l x 7" w x 6.7" h ( 288 x 178 x 171 mm) 4, self priming: more than 2 meters 5, port size: hose tail connection 3/4" 6, pressure max: 25psi (1.5bar) 7, diaphragm material: vition 8, check valve made: vition 9, voltage: 12v, 24v dc115v, 220v, 230vac 10, power : on/off switch 11, head of pump: glass fibre 12, body material(dc): glass fibre 13, body material(ac): aluminium 14, liquid of application: water, oil, urea, adblue Carton case with pallet
Steel square section rolling, pump equipment.
Any pump, spare parts.
Spare parts of mud pump.
Spare parts.
Mud pump parts.
Moldel: zpk-dc2l2000y03s Voltage: 24v Power: 20w Max static water head : 3m Dimension of outlet : 17.5mm Net weight : 0.75kg
The product is cantilever, centrifugal pump. Horizontal, vertical axial open double pump shell structure, lined with carbide or rubber with good wear resistance, corrosion resistance and high reliability. Product structure is reasonable, reliable operation, long life and other characteristics. Especially for high concentrations, strong abrasion conditions.
1) cooling capacity: we have 3kw to 1600kw model. 2) power : 3ph, 380v/220v/200v/415v 50hz/60hz 3) refrigerant type: r22 / r134a / r407c / r404a / r410a 4) the choice of imports of semi-closed original double-screw compressor, reciprocating compressor, compared with the traditional, high efficiency, quiet operation, simple operation and long life. 5) using the world famous brand refrigeration parts, to ensure the quality and stable unit. 6) evaporator, condenser threads are using the latest high efficiency and ensure a good cooling unit performance. 7) independent of the cooling loop, separate maintenance and repair without affecting the machineâ??s use. 8) the unit uses micro-computer plc control, energy control system with the compressor section can be timely and accurate cooling capacity control mechanism and the cooling load matching, to ensure the most efficient plant operation, lowest energy consumption and achieve energy-saving and reliable operation. 9) able to monitor the setting of actual temp, and display temp, trend in hours or daily.
Water Supplying Booster Pump ? Usage: Water supply for High height Apartment, Shopping Mall, Hotel, Hospital, Industry buildings. ? For unstably water supplied area, or wide range area - Combination of pump Set + Inverter control panel + Pressure tank separation type factory releasing - Possible to change direction by equipping suction/ discharging flange - Possible to adjust head bore according to site condition - Possible to have basic dual (Inverter) type as for products below 11Kw 2 pump
