The venus relay protection tester is developed using advanced dsp (digital signal processor) and switching amplifier technologies, which can test electromagnetic, transistor, integrated circuit and microprocessor relay protection equipments. Venus relay protection test software is an automatic testing management platform for protection device. The highly efficient system consisted of venus and the software can meet the requirements for the research institutions and manufacturers in the power system of the world. 4/6 ac or dc voltage sources 3/6 ac or dc current sources 0-250v independent dc voltage source Measurement for kwh and transducer Internal and external gps synchronization Ethernet interface(rj45) for communication 4 binary output, 8 binary input Powerful test system, rich function, cost effective Calibrate all kinds of protection devices. Measurement for transducers and kwh meters. Easy to operate. - all interfaces are on the panels of the device. - tester can stand or lies according to userí»s needs Light weight, and portable. Small power consumption, good heat dissipation
This is the most advanced automatic version of the c&df sets within our product range. The automatic 12kv 200ma test set integrates the high voltage power source and the measuring bridge into one single compact unit. It is designed to measure dissipation factor and capacitance in heavy electromagnetic interference environment such as in power plants and substations. Using digital filters it eliminates interference signal to specimen signal by a ratio as high as 2:1. It can also be used in laboratory for high accuracy tests on high voltage bushings, transformer windings, shunt reactors, current transformer, capacitor voltage transformer (cvt), grading capacitors of circuit breakers, surge arrestors and generator windings. Dissipation factor range v no limit Df resolution v 0.001% (1 x 10-5) Df accuracy v 1% + 4 digits Capacitance range v 3pf to 50000pf @ 12kv 60pf to 1uf @ 0.5kv Capacitance range accuracy v 1% + 1 digit Test voltage range v 0.5kv to 12kv, 200ma(max) Test voltage resolution v 1v Test voltage accuracy v 1% + 10 digits Input current range v 10ua to 5a Test time v 30s typical Cvt test mode v o/p voltage 3 to 50v, o/p current 3 to 30a Internal hv frequency v 45, 50, 55, 60, 65 hz (single) 45/55hz, 55/65hz (auto multiple frequency measure & avg for interference suppression) Input supply v 1-phase 220v 50hz, +/- 10% (flat pin type, type g electrical plug) Printer v thermal printer Communication port v rs-232. Moq - 1 pc Weight - 35 kgs Dimensions - 45cms x 35cms x 35cms.
Designed to test all types of relays. 6 x 30 a ac/dc 4 x 125 v ac/dc 1x 3 a /100v 1 x 0-265 v aux DC 8 binary inputs 4 binary outputs Rs 232, ethernet port Based on linear power amplifier techmology, the test set is highly accurate and is the economical solution for relay testing. 15 kg
The repair tester for Common Rail Injector CRI-1000 simulates the outputs of an Engine Control Unit (ECU) to provide user adjustable fuel injection control signals for driving the solenoid of a common rail injector. The CR injector being tested is fed by a high pressure fuel source, which may be a mechanical manual pump or an electrical motor driven pump or a pneumatic driven pressure booster. Such a test device will fulfill the tasks of checking nozzle spray pattern, injector back leakage and solenoid condition. Design Features Modulated driving signal to ensure the safety of the injector solenoid Adjustable frequency and pulse width for the injector driving signal Short circuit protection for solenoid driving signals Rich accessories, ready to test Bosch, Denso and Delphi injectors 40*37*20cm
Common Rail System Tester CRS-1000 simulates an engine ECU, to drive a solenoid on CR pump, such as Bosch CP1/CP2/CP3, Delphi CRSP and Denso HP2/HP3, and solenoids of 6 CR injectors. A standard high pressure pump test bench with a CR system tester CRS-1000 will fulfill most tasks for repairing a CR system and the components, such as injection quantities, injector fuel return, nozzle injection spray atomization, pump condition and fuel rail pressure control. Design Features Combine two independent modules for pump and injector control Pump driving signal - Adjustable duty cycleíAwhile monitoring fuel rail pressure Injector driving signal - Adjustable frequency and pulse width Modulated driving signal to ensure the safety of the solenoids of the injectors Software based over-pressure protection Short circuit protection for solenoid driving signals Rich accessories, ready to test Bosch, Denso and Delphi injectors and pumps 50*43*30cm
LCD displays ATX power voltages Tests 20-pin and 24-pin power supplies Tests SATA power Tests Pentium 4 power connector Tests PCI-Express power connectors Tests Xeon power connectors Tests Floppy drive connectors Tests standard 4-pin power supply connectors Tests for +3.3V, -12V, PG, +5VSB, +12V, -5V, +5V outputs Aluminum Case Accurate Voltage indicator +/- 0.1V Displays ATX P.G. values Low or High PG aalues alarm ATX output connectors check Over voltage alarm No Voltage alarm Low Voltage alarm Blister
V-checker circuit tester
Universal fiber continuity tester Fast, easy to use, economical when compared with other testers Activate the high-intensity led light beam with a simple twist 24+ hours continuous use battery life with patented circuitry design Allow direct inspection from fiber end (singlemode or multimode) for continuity testing Elegant color anodize finishing for corrosion resistance, particularly important when using under hazard environment Rugged machined aircraft aluminium alloy construction Singlemode or multimode fiber testing Compact in size and easy handling Suitable for all 2.5mm connectors (fc, sc, st, fddi, escon), 1.25mm connectors (lc, mu) and sma connectors Red led light source, able to transmit light through 2km multimode fiber (subject to the fiber characteristics) Comes with handy blister package Blister packing
Features: 1, each durometer type is made to a specific scale (i. E.A, c, d) and is capable of producing a value between 0and 100. Shore a is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials. Shore d is designed for plastics, formica, epoxies and plexiglass. 2, it meets standards: din 53505, iso 868, iso 7619, astmd 2240, jisk7215. 3, used the exclusive micro-computer lsi-circuit and crystal time base to offer high accuracy measurement. 4, digital display gives exact reading with no guessing and errors. 5, can communicate with pc for reading, printing and analyzing by the optional software and cable for rs232c interface. 6, automatic power off to conserve power. 7, use operation stand of optional parts can get good accuracy and repetitiveness due to constant measurement force to eliminate the errors caused by artificially applied different force. Dimensions: 162x65x38mm
Ft-f1 fogging tester Characteristics: Determines auto's fogging characteristics precisely, guarantees automobiles driving safely. Be applicable for the laboratory and works in low noise. Data test and analysis with professional software, convenient and prompt. Bath temperature controlled by thermostat can be kept constant to 0.1ªc, creating precise testing conditions. Designs friendly and integrally, operates safely and conveniently. World-famous brand elements with stable and reliable performance. The strictly controlled constant thermostat can be used for the other experiments. Conforms to din 75201, iso 6452, sae j1756.
Glow wire tester Discussion of the Glow Wire Test (Varies as per relevant standard): 1. Object of the Test - Components or parts under Fault or Overload conditions, may attain a Temperature such that they will ignite parts in their vicinity. The GLOW - WIRE Test simulates thermal stresses which may be produced by such source of heat or ignition. e.g. glowing elements or overloaded resistors, may be for short duration, in order to assess by a simulation technique the Fire Hazard. 2. General Description of the Test - a. If possible, the specimen should be a complete equipment, sub-assembly or a component. b. While taking a part / parts of an enclosure for the Tests, care must be taken to ensure that the Test Conditions are not significantly different from those occurring in the Normal usage, with regard to shape, ventilation, effect of thermal stress and possible flames occurring, burning or glowing particles falling in the vicinity of the specimen. c. The Test is applied to ensure - 1. That the Glow - wire Loop which is electrically heated to a temperature specified, does not under defined conditions cause ignition of the Part/Parts. 2. That the part which might have been ignited, has a limited duration of burning, without spreading of fire by its flame or burning or glowing particles. d. This type of test may not be appropriate for too small components / parts / sub assemblies, which may need Needle Flame Test. 3. Test Apparatus - a. The Glow - Wire consists of a specified loop of a Nickel / Chromium ( 80/20 ) wire of 4 mm dia. b. Sheathed fine wire thermocouple, of overall dia. 0.5 mm ( wires of NiCr & NiAl ) with welded point / joint located in the 0.6 mm hole in the Loop of Glow - Wire. c. The Sheath consists of metal , resistant to a temperature of 960 deg. C in working. d. The instrument for measuring thermovoltage have 1 % accuracy. e. The Test Apparatus is so designed that the Glow - Wire Loop is horizontal and the mounted specimen moves horizontally towards the Loop with a force applied 0.8 to 1.2 N, for a penetration distance of 7 mm max. f. To evaluate the possibility of spread of fire, a layer of the material or components normally surrounded underneath the specimen is placed underneath the specimen at a distance equal to the distance between the specimen and the surrounding material or components when the specimen is mounted as in normal use. If a subassembly or a part of the equipment is tested separately, a piece of white pinewood board, approximately 10 mm thick and covered with a single layer of tissue paper, is positioned at a distance of 200+/- 5mm below the place where the glow-wire is applied to the specimen, unless otherwise specified in the relevant specification.
PH-903 Pen pH Tester WR PH-903 Pen pH Tester WR (New) Range: 0.00-f-¼14.00 pH, Resolution: 0.01 pH, Accuracy: -f+ú-f+¦0.03pH, Temp. C: 5-f-¼50-f+¬, (ATC) Calibration: Two-point at 6.86pH and 4.01pH (or 7.0pH and 4.01pH) Features: Automatic switch-off function: After 10 minutes without pushing buttons, the meter will be switched off automatically. Low battery: As long as there is any display, the accuracy is guaranteed. Battery Life: DC 4x 1.5V Flug: Fixed electrode 0
Electrical voltage tester Contact ac voltage range: 80v to 500v Long life of neon lamp, turn/off 50000 times or more, flash up to 20000 hours Shell made of transparent plastics, impact-resistant, insulation voltage up to 1000v The end with a hole for hanging up, hardness of blade head up to hrc52 40x26x22.5cm N/g 7.56kg/9.93kg
Eltek Flatpack2 Rectifier Module 110V 2000W HE WOR 241119.805 Overview High efficiency and reliable rectifiers The most efficient power conversion module in the industry! Since the launch the Flatpack 2 family has expanded into a wide selection of power ratings and voltages Key Feature Proven Reliability High Power Density Application Flexibility, 2kw - 2m Accepts Dc Input (Dc/ Dc Converter) Global Compliance (Ce, Ul, Nebs) Marine & Offshore Certification Patented Technology Digital Controllers Applications Power Utilities Switch Tripping Control & Protection Systems Emergency Lighting Railway Infrastructure Converter Stations Power Stations Various other applications in demanding industries like marine, oil & gas, process etc. Specifications Part number 241119.805 Model 110-120 / 20A HE INPUT DATA Voltage range (nominal) 176 - 277 V AC 1) Voltage range 85 - 305 V A 1) C Frequency 45 - 66 Hz Maximum current 18.64 ARMS Power Factor 0.99 (@ 50-100 % load) THD (@ 230 VAC) < 4 % (@ full load) Protection Varistor for transient protection, fuse in both lines, shutdown above 300/ 305 V OUTPUT DATA Default voltage 122.5 V DC Voltage range 90.02) - 151.25 V D 1) C # Pb cell supported (1.8 - 2.4 V DC/ cell) 54 -60 # NiCad cell supported (1.05 - 1.65 V DC/ cell) 86 - 91 Max power, nominal input 3025 W1) Max power, 85V input 1280 W Max current 20 A Hold-up time, default voltage and 1500 W load 10 ms, VOUT > 99.7 VDC Current sharing �±5% of maximum current from 10 to 100% load Static voltage regulation �±0.5% from 10% to 100% load and nominal input Dynamic voltage regulation �±5.0% for 10-80% or 80-10% load variation, regulation time < 50ms Rippel and noise, 30 MHz bandwidth < 500 mV PP Protection Overvoltage shutdown, short circuit proof, high temperature, hot plug -in inrush current limiting, ORing diode
Main Features 1.Measuring Range0.01-1200 2.Stored Data99 sets 3.Clamp Size64mm*32mm 4.Power Consumption:Maximum 50mA 5.Current range:0.00mA-20.0A Model No.: MEWOI3000D+ Name: MEWOI3000D+-0.01-1200/0.00mA-20.0A Clamp on Earth Resistance Tester/Meter,earth ground tester,GEO Tester Low Battery Indication: Low battery symbol displays when battery is lower then 5.3VPower Consumption Power consumption:Max 50mA either in booting up or normally working, Continuously working for 30 hours
MEWOI3100B+ Clamp Earth Resistance Tester is widely applied in ground resistance measurement, loop resistance measurement in fields such as electric power, telecommunications, meteorology, oil field, architecture and industrial electrical equipment, etc. When measuring ground system with loop, there is no need to disconnect the ground wire without auxiliary electrode, which means safer and faster. MEWOI3100B+ Clamp Earth Resistance Tester can measure the ground fault which can not be measured by traditional method, can apply in the occasion where traditional methods are unworkable; MEWOI3100B+ Clamp Earth Resistance Tester measures the integrated value of ground resistance and resistance lead. Main Features 1Measuring Range0.01-200Ω2Stored Data99 sets3Clamp Size32mm4Power Consumption:Maximum 50mA Model No.: MEWOI3100B+ Name: MEWOI3100B+-0.01Ω-200Ω Earth Resistance Clamp meter/tester
Main Features: 1,Equipotential bonding resistance Test,2,low value resistance test, 3,DC resistance test Model No:MEWOI4700 Name: MEWOI4700 Equipotential&DC low resistance testerMain Function:Test of equipotential bonding resistance between functional metal components, low value resistance test, DC resistance test, resistance test of connecting conductor in ground network ground pole, contact resistance, riveting resistance test, wire length test, etc. Test Wires:2 red and 2 black wires, each 5m
Applications Used for hydraulic and pneumatic systems Compressors, compressed air system Suitable for fluid medium which does not clog connection port or brass Special use for stable and long life. Case:black steel Ring:black steel Window:acrylic Socket & connection:brass Movement:brass Bourdon tube:copper alloy Pointer and dial:aluminum Range:vacuum, compound 0 to 6000 psi Class:1.6% Mounting type:bottom
Applications Used for hydraulic and pneumaitc systems Compressors, compressed air system Suitable for fluid medium which does not clog conenction port or brass Uesd for providing protection from vibration and pulsation. Case:stainless steel Ring:stainless steel Window:pc Socket & connection:brass Movement:brass Pointer and dial:aluminum Liquid:glycerin, silicone Range:vacuum, compound 0 to 6000 psi Class:1.6% Mounting type:back
Purpose SYF71 crack width and depth tester is used to test the crack depth and width. It is one professional crack measurement in one comprehensive test instrument, mainly used for crack detection of bridges, tunnels, walls, concrete pavement, metal surface. Specification The People's Republic of China Housing Security accreditation standards --- GJ125-99 Technical specification for inspection of concrete defects by ultrasonic method (CECS 21:2000) Performance/Functions 1. Large-screen display: 5 "color LCD display with a resolution of 640 * 480; 2. A high degree of intelligence: the boot that is measured, without human involvement parametric interpretation, display sewn deep value; real-time detection and automatic interpretation crack width, but also the manual interpretation crack width value, manually move the cursor to define the crack boundary is displayed on the screen scale ruler display crack width value; 3. Deep test: maximum test depth up to 650mm; maximum width up to 8mm 4. Dedicated scale: instrument equipped with a dedicated scale, portable and practical, to improve the efficiency of the test. 5. The instrument can be set and saved the test date: user-friendly data management 6. Easy data transfer: the instrument can be directly connected to the computer, copy pictures and data transmission without U disk; 7. Powerful professional windows data analysis processing software: data can be imported into Word and Excel, convenient and user-friendly post-processing of data. Technical Measurements 1. Crack depth testing range: =< 650 mm; test error: =< 10%; 2. Crack width value of measuring range: 0 ~ 8mm; width measurement accuracy: 0.01mm; 3. Crack depth test data storage capacity: 6000 set of test data; 100,000 and can store the image and width of cracks measured point data; 4. LCD screen resolution: 160X128 dot matrix 5. Built-in rechargeable lithium battery, can work continuously for eight hours; 6. Operating Temperature: -10 ? ~ +50 ?; 7. Host size: 190mm × 183mm × 84mm
