GY-41 rigid box folding in machine is use to bend the extruding parts of the surface paper into the boxes.This machine has simple structure, convenient operation and fast speed features. It is used to side fold various sizes and shapes of paper boxes and the sizes and shapes can be adjusted 1 right angle platform for double side inner folding onto the paper box. 2 equipped with sensor to control the device. 3 platform can be adjusted according to the depth of the boxes. Model GY-41 Case size 420*420*150mm Speed 20-30 units/min Power 0.5kw, 220v Weight 240 kg Dimension 1000*700*1000.
Length: 1200mm Diameter: 50mm~150mm Paper Wall: 0.5mm~5mm Cutting Way: by air Power: 1.1KW Cutting Units: 8sets Size Of Disc Knife: 110x27x1.5mm. Weight: 0.8 ton Dimension: 2000x800x1200mm.
Tube Diameter: 30mm~300mm Tube Wall Thickness: 0.5mm~12mm Speed: 3-15m/min Cutting Length: Max 4000mm, flowing cutting controlled by photoelectricity switch. Power: Main Machine 5.5kw; Cutting: 0.75kw Control way: Frequency conversion; Multipoints in-phase control Transmission Way: Screw umbrella gear wheel Size of wheel: 320mm Cutting Way: Automatic cutting Belt way: Both right side and wrong side are ok Belt: circle nylon ,1pc Paper shaft: 1pc (with plating chrome) 3"or by order Glue System: ship, both sides of paper layer Paper-putting Frame: whole jointing steel, with little crane Bottom paper and face paper has own paper putting frame Sending paper from both sides (15layers),1 set glue tank. With heating bonding device for inner aluminum foils. Wegiht:3.2t Dimension: main machine 3200x2000x1800mm.
Tube Diameter:20mm~300mm Tube Wall Thickness: 0.5mm~20mm Speed: 3-15m/min Cutting Length: Max 4000mm,flowing cutting controlled by photoelectricity switch Power: Main Machine 15kw; Cutting: 0.75kw Control way: Frequency conversion. Multi-points in-phase control Transmission Way: Screw umbrella gear wheel Size of wheel:320mm Cutting Way: Automatic cutting Belt way: Both right side and wrong side are ok Belt: circle nylon ,1pc Paper shaft:1pc (with plating chrome) 76mm or by the buyers order Glue System: ship, both sides of paper layer Paper-putting Frame: whole jointing steel,with little crane Bottom paper and face paper has own paper putting frame Sending paper from both sides,1 set glue tank. Weight: 3.2t Dimension: main machine 3200x2000x1800mm.
1, Paper roll width : 1400mm 2, Sheet accuracy : 0.3 mm 3, Optional equip with Germany Synchronization controller, accuracy : 0.2mm 4, Max. cutting speed : 300 m/min 5, Max. rotation speed : 400 r/min 6, Sheeting length : 300 ~ 1550 mm 7, Sheeting thickness : 180 ~ 400 gsm. Sheet pilling height : 1400mm Weight : 12ton.
Machine specification 787mm single cylinder single nets paper machine NO. Technology parameters 1 Output paper types High-grade toilet paper 2 Raw material Waste paper, whiet paper brim, wood pulp 3 Grammage 13 40g/m2 4 Net paper width 787mm -900mm 5 Net width 1100mm 6 capacity 0.8-1.0t/d 7 Rail guage 1300mm 8 Transmission way Slow transmission with 250 type reducer. 1. Part use of the wooden case straw rope 2. Finally,according to the contract requirement.
MJRY-2 Creasing and Die-cutting Machine (With Inverter For adjust the speed) It is a kind of special equipment for all assortments of common card boards, corrugated boards, plastic sheets, leather products. It is suitable for printing, packing, decorating, plastic industries etc. with the features of firm structure, exquisite marking, greet cutting, high precision, ease of operation, safety and reliability etc. This Series Creasing and Die-cutting machine use Inverter to adjust the speed.
MJT model 3-Layer Corrugated Paperboard production Line Introduction Corrugated cardboard production line includes mill roll stand, single facer, pre-heater, conveyer bridge, gluing machine, slitter scorer machine, cut off machine and stacker. We can produce the three ply, five ply and seven ply corrugated cardboard production line, Widths from 1400 to 2500mm\min,production speeds from 60 to 250 meters/min Customer's can choose according his own needs. We can provide a complete production line and can also provide individual parts to complete customer's own line. Equipments List Equipments Name MJT-60-1600 Economical MJT-80-1600 Standard MJT-100-1600 High-speed Mechanical Roll Stand (include the paper roll rail.) 2 2 Hydraulic Roll Stand (include the paper roll rail.) 3 Pre-heater (diameter 400mm)(Up) 1 2 Pre-heater (diameter 600mm)(Ground) 2 Vacuum Single Facer (Roll 280), gimbal drive 1 1 Vacuum Single Facer (Roll 320), gimbal drive 1 Transport Bridge (Electrical adjust the precision, vacuum tighten and loosen.) 1 1 Heavy model transport bridge (Electrical adjust the precision, vacuum tighten and loosen.) 1 Double preheater (diameter 400mm) 1 1 Double preheater (diameter 600mm) 1 Double Gluer - A 1 1 Double Gluer - B 1 Double baker (600mm X9heat plates, 4.5meter cooling part.) 1 Double baker (600mm X11heat plates, 5meter cooling part.) 1 Double baker (600mm X14heat plates, 6meter cooling part.) 1 Thin Blade (Simple electrical adjust.) 1 High-Speed Thin Blade(Electrical up and down, electrical adjust the precision.) 1 1 Mechanical Cutter 1 NC Cutter (Servo, straight knife.) 1 1 Conveyor and Stacker 1 Paperboard booking machine 1 Glue system 1 1 1 Steam system (not include the boiler and pipes.) 1 1 1
MJDX-2 Stitcher (Stapler) Introduction: MJDX-2 Stitcher (Stapler), the head of the machine is made with electromagnetic clutch and electromagnetic arrester. The machine has advantages as working reaction speed is high, low noise and so on. The carton stapler is the special equipment for nailing the corrugated paper carton and paper box with double-feed device. It can nail double line oblique according to 45degree at the same time and nail the big and middle size paper case continuously or interruptedly. Sizes available: 600mm, 900mm, 1200mm, 1400mm, 1600mm, 1800mm. Technological parameters: Main technological Parameters: Model MJDX-2 Speed 400 stitcher/min. Working thickness 3-ply, 5-ply paperboard Stitch type 45¡ã double lean-nail Width of stitch feet 13mm Size of stitch wire 17# Operation table height 1.2m Motor power 0.55KW Machine Weight 650kg
MJSGL-2 Single Facer Line (2-layer corrugated paperboard production line) (2-ply corrugated paperboard line) Roll Stand Single Facer Paperboard Cutter Note: For the Single Facer line, we can produce different model roll stand, single facer, and paper cutter as customer's requirements. Introduction: Single facer line is also called 2-layer corrugated paperboard production line. This Single facer Line is composed of Paper Roll stand, Single facer machine, circumvolve paper cutting machine. To use the web paper material single face machine production line, producing and cutting single face corrugated paper as required sizes, it forms the corrugated board with no need drying. This unit has the advantages of reasonable fabric, advanced technology, high quality of production, high efficiency, low workmanship, operation and maintenance easy. This is the preferred equipment for the production of corrugated cardboard of the cardboard factories. Technological Parameter: Working Width 1400mm 1600mm 1800mm 2000mm Heating method Electrical heating/Oil heating / Steam heating Design speed 40-70m/min Economical speed 30-60 m/min Compress-air pressure 0.4-0.9MPa Flute type Standard flute UV Flute Standard spec. A,B,C,E,F
MJRS-1 Hydraulic Mill Roll Stand 1) The sturcture is double rotary shafts with four arms; Support two paper mill rolls on both arms at the same time. 2) Hydraulic control for paper mill roller up-down, clamp-open and centering. Or motorized clamp-open and centering. 3) Using multi-point brake which imports from Italy and automatic expansion springiness chucks , Reduce paper waste. 4) Effective width:1400mm-2800mm. 5) Maximum paper roll diameter:¦Õ1500mm. 6) Maximum support weight: 7T. 7) Main axis:¦Õ270mm HS CODE: 844180900
MJSF-380D Single Facer (Double Flute) Purpose and Characteristics: 1) Design speed:200m/min 2) Effective width of machine: 1400mm-2500mm 3) Main flute roller diameter¦Õ380mm, pressure roller diameter¦Õ385mm, preheater roller diameter¦Õ400mm. 4) Vacuum suction paper leading features perfect flute formation 5) Dual flute structure, one pair flute rollers unit working and another preheating, achieve flute quickly change. Save working space ( if normal single facer machine need two sets to achieve this function ). 6) PLC control system. Touch screen display all running data, easy for operation. 7) The flute rollers made by special alloy steel with hardness treatment . it' hardness can reach HRC58-60, The surface is well treated by grind and plated chrome, or adopt Tungsten carbide flute rollers are optional. 8) The independent driving box, five driver axis, all gears with hardness treatment, oil spray lubricating by oil pump to reduce noise keep running stable, prolong the use life of gear. 9) Adopt Glue width motorized dividing to match the paper width. Idle running motor for glue applicator roll to avoid glue dry. Adjustment for gap between glue roller and doctor roller by electric . Digital read out for the gap between glue roll and doctor roll. Glue unit can be moved by pneumatic. 10) Flute rollers and pressure roller controlled by hydraulic system, working pressure stable. 11) With water spray device for adjust moisture capacity of flute paper. 12) This dual flute machine suit for single facer paperboard production line ---2 layer (Single facer paperboard ) and corrugated paperboard production line--- 3 & 5 &7 layer. With high market competitive power.
MJSF-320FX Single Facer Introduction: Single Facer is the main machine for producing the corrugated paperboard. Vacuum suction model single facer has very good production precision. The choose of the machine is directly effecting the quality of the corrugated paperboard. Characteristics: * Paper leading with Vacuum absorb model, have high-pressure & strong fan motor. The flow of fan can be adjusted, and have silencer; The electric control system fastens on a electrical case, which has min. 1.5meter distance from equipments, the operation side is completely independent. * Gimble drive system, separated structure and independent drive case. Closed gear drive system with oiling lubrication, the usage life of the gears is highly prolonged. * Machine base and wallboard is cast iron structure, thickness of the wallboard is 180mm. * Corrugated Roll: Material of corrugated roll is 52CrMo alloy, which is dealt with quench, surface polish. Diameter of roll is Ø 320mm, surface hardness is more than HRC60. The adjust of up and down of roll is pneumatic controlled. * Press roll: Diameter is Ø320mm, surface is worn down and chromeplated. The adjust of up and down of roll is pneumatic controlled, material is Carbon Iron 45#, dealt with confection. * Pre-heater Roll: Diameter is Ø400mm, surface is worn down and chromeplated. All are connect with soft metal pipe. * The bearing of corrugated roll and press roll are lubricated and high-temperature resistant. * Glue supply and quit is pneumatic controlled, diameter of glue roll is Ø240mm, surface of roll has concave netted rind, surface polish & chromeplated. Surface of adjust roll is surface polish & chromeplated. * Use electrical glue separate equipments, the glue part can run independently when the main motor stops, this can avoid the dry of the glue.(Choose by customer.) * Middle height of corrugated roll is 0.10mm, middle height of press roll is 0.075mm. Have place limit equipment, diameter of tighten cylinder is Ø160mm. Technological Parameters: 1. Working width: 1600mm, 1800mm, 2000mm,2200mm. 2. Design speed: 120m/min. 3. Operation direction: Left or right (design as customer’s workshop.) 4. Gas: 0.4-0.9Mpa. 5. Steam pressure: 0.8-1.3Mpa. 6. Flute: UV or UVV model, can design as customer’s requirement. Diameter of the rolls: 1. Corrugated Roll: Ø320 mm 2. Press Roll: Ø320 mm 3. Gluing Roll: Ø240 mm 4. Pre-heating Roll: Ø400 mm Drive Power: 1) Main Motor: 11KW, 380V, 50HZ 2) Fan Motor: 15KW, 380V, 50HZ
MJSD-2 Paperboard Cutter Machine (Light model) Introduction MJSD-2 Series Rotary Die-Cutting Machine (Light model) is used for the transverse and vertical cutting of the paperboard as customer¡¯s requirement. The machine use chain model drive, have big turning moment. The machine has reasonable structure, the cutting precision is high and adjust is fast. The machine is electromagnetism speed adjust, continuous feeding, mechanical control, it can work together with the single facer machine as single facer line for producing the 2-layer corrugated paperboard. The knives quantity can be required by the customer. Transversely cut 400-2400mm. Technological Parameters Model MJSD-2-1700 MJSD-2-2000 Max. Cutting width. 1700mm 2000mm Cutting length 200-2000mm 200-2000mm Cutting times 20-120times/min 20-120times/min Cutting thickness 2mm 2mm Power 3kw 3kw Working Speed 0-70m/min 0-70m/min Machine Size 2250*1400*1300mm 2750*1400*1300mm Weight About 1500kg About 1700kg
MJZX-2 Semi-auto Carton Gluer Machine Introduction: Semi-auto Carton Gluer Machine is new machine for carton production in recent years. It is mainly used for the glue of the carton. It can glue for 3-layer, 5-layer, 7-layer paperboard and so on. The machine structure is easy, working is stable, operation is simple, production efficiency is high, gluing quality is good, production cost is very low. The cost is 15times lower than steel wire stitcher machine. Machine structure: Machine frame, up and down working-table, front transport equipment, front revising equipment, middle transport equipment, middle press equipment, finished product side output equipment, electrical control equipment. Characteristics: Easy and reliable operation system. Novel design of the whole machine. High-speed changing sizes. Automatically counting and strap setting. Technological Parameters: Model MJZXJ-2 Max. Size (L+W)*2 2460mm Min. Size (L+W)*2 340mm Max. Size (W+H)*2 1515mm Min. Size (W+H)*2 240mm Paperboard feeding height 900mm Power 2.2kw Mechanical Speed 40m/min Machine Packing Size 4.5*1.95*2.0m Machine Weight 2000KG Note: We can produce different size machine as customer¡¯s requirements.
MJMQ-3 Rotatory Die-Cutting Machine (Chain model) Front Photo Back and side Photo Introduction MJMQ-3 Series Rotatory Die-cutting Machine is driven by chain. It is used for die-cutting corrugated paperboard and different kind atypic packages. The advantage of the machine is high efficiency, power save, good safety and so on. This machine use PU roller cover which is imported from Taiwan, the usage life is more than 10million times. The machine has the function of automatically line-speed compensation, this function makes the die-cutting size of the paperboard is exactly right even when the roller cover is attrited. The renovate structure 3times prolongs the life of the roller cover. The feeding system use chain transport. The operation and usage is very easy. Die-cutting part: 1) The roller uses high-grade steel, surface is abrasive with hard chromeplated. 2) Automatically revise the parallel, running stably. 3) Use PU roller cover which is imported from Taiwan. 4) The rubber roller have transverse 50mm moving system. 5) Automatic compensation of the line-speed means: the automatic compensation structure makes each batch carton size same after die-cutting without worker¡¯s operation. 6)The roller cover can automatically rehab, this prolongs the use life of the roller. Technological Parameters Model Max. Paperboard size(mm) Min. Paperboard size(mm) Thickness(mm) Main Power(kw) MJMQ-3-1600B 1600¡Á1350 300¡Á500 1-8(3-5layer) 4.0 MJMQ-3-1800B 1800¡Á1350 300¡Á600 1-8(3-5 layer) 5.5 MJMQ-3-2000B 2000¡Á1600 400¡Á600 1-8(3-5 layer) 7.5 MJMQ-3-2400B 2400¡Á1600 400¡Á700 1-10(3-7 layer) 7.5
MJKC-1 Series Paperboard Cutting, Pressing Line, Slotting & Cutting corner Machine Introduction MJKC-1 Series Paperboard Cutting, Pressing Line, Slotting & Cutting corner Machine is and integrated machine used for the cutting, slotting, pressing line and corner cutting of corrugated paperboard. Its special characteristics are high production efficiency, good quality and easy operation. (We can also add the function of holing and carton window on this machine.) Technological Parameters Model Max. Paperboard size (mm) Min. Paperboard size (mm) Slotting Depth (mm) Work Speed (m/min) MJKC-1-1800 1750¡Á1470 650¡Á350 500 0-80 MJKC-1-2000 1950¡Á1470 650¡Á350 500 0-80 MJKC-1-2200 2150¡Á1470 650¡Á350 650 0-80 MJKC-1-2400 2350¡Á1470 650¡Á350 650 0-80 MJKC-1-2600 2550¡Á1470 650¡Á350 650 0-80
MJTJ-3-750, 930, 1040, 1100, 1200 Hot Stamping and Cutting Machine The series of model TYMB gilding, cutting & mark pressurized machine is product of new generation with clockwork precision and marked effect. It is used for gilding-printing all kinds of colored electro-chemical aluminum, marking a concave-convex die-cutting pictures, trade mark, advertisement of sample, boxes, cover of books and new year card, highly decorations and printing materials. It is the optimum equipment for printing, packing, decoration and plastic industries with materials including paper, cardboard, plastic, leather matters. Characteristics It adopts high quality material and high tension of casting It adopts four-shaft bevel wheel structure with steady operation, great cutting, low noise. Sound and layout of its height, great angle of frame. Electrical system is designed according to IEC standard. It has three functions for single slitting, successive slitting, time delay. Its can be adjusted. Safety protection system is reliable. Concentrated lubricating system. Main Specification Model Max.Platen Working Area Max.Gilding Printing Area Skip Order Range Working Pressure Foil-delivered Length Foil-delivered Group Working Speed Main Motor Overall Power Overall Dimensions Total Weight TYMB750 750*520mm 740*510mm Built-in Processing With Computer 100T 500mm 2groups 1380Time/h 2.2kw 10kw 2150*1400*1900mm 2500kg TYMB930 930*670mm 920*660mm Built-in Processing With Computer 170T 640mm 3groups 1320Time/h 4kw 13kw 2200*2000*1950mm 3500kg TYMB1040 1020*700mm 1020*700mm Built-in Processing With Computer 170T 700mm 3groups 1320Time/h 4kw 13kw 2230*2100*2000mm 4500kg TYMB1100 1080*780mm 1080*780mm Built-in Processing With Computer 220T 800mm 3groups 1200Time/h 5.5kw 19kw 2250*2200*2000mm 5000kg TYMB1200 1180*800mm 1180*800mm Built-in Processing With Computer 220T 800mm 3groups.
MJRJ-5 Series Die-cutting and Creasing Machine 1600-1800 Introduction MJRJ-5 Series Die-Cutting and Creasing Machine is the special equipment for die cutting and creasing many different kind sheet shape materials. Such as hard paperboard, corrugated paperboard, plastic, leather and so on. It is widely used in printing, packing and decorating industry. Our companie¡¯s product with its high-quality and competitive price are popular by our customers all over the world. Characteristics 1. Sliding bearings are made of high quality alloy cooper, thus to get effect of anti-friction and shake reducing. 2. Flywheel is with big moment of force and large pressure. 3. High strength due to one piece casting by using top-ranking material for machine body. 4. Single plate electromagnetic clutch is sensitive and reliable. 5. Have functions of single cutting and creasing, continuous cutting and creasing and time-lapse opening, time-lapse range is adjustable. 6. Operation height is reasonable designed, the opening corner of the moving-bed is big. 7. Focus lubrication system makes the machine can lubricate very well, and reduce the abrasion. 8. Safety system is reliable. Technological Parameters Model MJRJ-5-1600 MJRJ-5-1800 Max. die-cutting and creasing area 1600*1250mm 1800*1400mm Working speed 16¡À2 strokes/min 16¡À2 strokes /min Max. Rule length
MJBL-6 Series 3-color big roll Flexo printer Function and Characteristics 1) The operating panel own double control function from full-face and lateral, special lateral control panel designed personality, it is very convenient and fast. 2) Choose dimensional design, reduce arched cardboard printing error and cardboard shift during the machinery running. 3) Adopt pneumatic locking and motorized detachment. 4) The working method of ink printing plate, pneumatic uplift printing plate, pneumatic uplife ink well, unattached electrical machinery running, cannot stop the ink when stop device, automatic ink equably. 5) Printing plate roller 360 regulation electrical phasing adjustment. (You can also choose CPU digital display phase adjustment function). 6) 45# steel high frequency heat treatment for gear running whole machinery, exact color and last well. Main Technical parameter Model number Roller diameter Over the paper width Area of valid printing Electrical power MJBL-6-1600 695 1800 2100¡Á1600 5.5 MJBL-6-1600 800 1800 2450¡Á1600 5.5 MJBL-6-1800 800 2000 2450¡Á1800 7.5 MJBL-6-2000 800 2200 2450¡Á2000 7.5 MJBL-6-1800 908 2000 2800¡Á1800 10 MJBL-6-2000 908 2200 2800¡Á2000 10
