Rubber Trimming Machine Introduction Frozen Shot Trimming an offshoot of cryogenic deflashing uses a system whereby parts are placed in a chamber, exposed to extremely cold temperatures (achieved with the use of liquid nitrogen) and then tumbled and blasted with a polycarbonate media. Because the burrs have a high surface area relative to their mass, they freeze very quickly and become brittle. The tumbling action combined with the impact of the media removes the burrs without damaging the part itself. Application Rubber NR NBR HNBR CR EPDM FKM ACM SILICONE Precision Plastic PA + GF PC + GF PPS POM PU PBT PTFE PEEK TPU TPE TPR Die - casting Alloy ZINC ALLOY MAG ALLOY Small and Round shape without sharp points will be more suitable for the Frozen Shot Trimming. SPECIFICATIONS NS - 60T Size: L1160mm * W1100mm * H2155mm Weight: 800kg Power Supply: AC380V 50HZ Electrical Capacity: 5KW * 3PH Design Temp: - 130Deg. C Design Pressure: 0.5 - 0.7 Mpa Outer Wall Material: SUS Frame Material: 100% SUS304 Barrel Capacity: 60L Wheel Speed: 7,200 rpm Max Barrel Speed: 0 - 26rpm Media Throw wheel Size : 250 Operation Mode: Touch Panel
Company Introduction Showtan Techno - Machine Nanjing Co. , Ltd. , the largest and most well - known manufacture of cryogenic deflashing machine in China, is a subsidiary company of a well - known Japanese cryogenic deflashing machine and gas products manufacture - Showa Denko Gas Products Co. , Ltd. , which is a member of the world famous multinational and comprehensive group - Showa Denko Group from Japan. Automatic Deburring Machine Introduction Automatic deburring is a process for removing flash from molded rubber parts. We use liquid nitrogen, high - speed rotation and shot blasted plastic media in varying combinations to remove the flash in a highly precise, economical and expedient manner. Parts that have thin flash can be quickly and thoroughly cryogenically deflashed. This process is exceptionally good at removing the inner dimensional and complex flash that cannot be removed by any other method. Application O - rings, gaskets and other rubber sealings Insulators and other electric / electronic components Valve stems, washers and fittings Short tubes and flexible boots Rubber absorbers and bumpers for automobile Face masks & goggles Mobile phone housing and intelligent watch strap Zinc and mag alloys like door lockers for auto cars SPECIFICATIONS NS - 60T Size: L1160mm * W1100mm * H2155mm Weight: 800kg Power Supply: AC380V 50HZ Electrical Capacity: 5KW * 3PH Design Temp: - 130Deg. C Design Pressure: 0.5 - 0.7 Mpa Outer Wall Material: SUS Frame Material: 100% SUS304 Barrel Capacity: 60L Wheel Speed: 7,200 rpm Max Barrel Speed: 0 - 26rpm Media Throw wheel Size : 250 Operation Mode: Touch Panel
Product Description It is used for beer waste, white wine grains and other high-humidity slag pressure filtration dehydration, strong dehydration, low power consumption, long service life, dehydrator manufacturer price is affordable, is the main equipment to achieve dehydration of winery waste. Principle The material passes through the conveyor, transported to the hopper of the dewatering machine, and evenly laid on the filter belt through the auger. The filter belt is leveled by the height of the material layer with the operation of the equipment so that the thickness of the material is completely uniform. Then, the upper and lower two ring-shaped filter belts are completely clamped, and the material layer is clamped by the driving roller, and the pair of rollers in the dewatering zone is mechanically pressed for several times to press out a large amount of water. According to the characteristics of the material, the extrusion force is automatically adjusted to meet the customer's requirements for material moisture.
Material: EPDM+PVC Hardness: 70±5 ShA Tooling cost: most of sizes are without tooling cost. Service: usually 50m/roll or as per customers' package. Should you have any requirement on rubber products, please feel free to contact me. Hope to get your early response.
We can produce FDA grade silicone gasket, the surface will be clean and translucent. The surface with etched or smooth that we can produced. We also can provided the FDA Certification, if you need, please let me know. If you have requirement on this kind of products, please feel free to contact me. I will glad to offer to you. I'm waiting here for your inquiry.
New product lab banbury mixer Dispersion kneader is used for rubber&plastic raw material mixing and dispersion, just like the pvc eva nbr sbr etc.The specific proposal would be based on the materials characteristic, production capacity. Specifications for dispersion kneader Type Unit Ln-1 to ln-10 Capacity Liter 1-10 Driving motor Kw 2.2-15 Flip device Hydraulic flipping Flip angle ° 110 Air compressor Kw 2.2 Water cooling Mpa 0.2-0.4 Electric heating W 650-1800 Size Mm About 1900*1000*2000 Weight Kg 800-2300 Main features 1) fit for various of high filled composites. 2) effective leak proof device. 3) m-w type pressurization for even dispersion. 4) accurate control system(temperature system ;electric system). 5) low maintenance by imported accessories.
Construction: Tube:oil resistant synthetic rubber. Reinforcement:four high tensile steel wire spiral layers (4 w/s). Cover:â abrasion and weather resistant synthetic rubber. Temperature range40c to +121 c. Applications: Ideally suited for high-impulse applications. No skiving required with w-series fittings. Recommended for petroleum and water-bases hydraulic fluids in very high pressure applications. Meets or exceeds all sae 100r12 specifications.
Construction: Inner Tube:Polyester elastomer(cream color). Reinforcement:One polyester braid. Cover:Proprietary urethane blend("Tuff-Skin"). Cover color:Black,non-perforated(other colors available). Temperature range: -40F-135F(-40C-57C)Limited to 150F(+66C)for water-based or fire resistant fluids.(Delta) working length at rated WPSI:±2% max. Features: Bonded construction,slim profile and light weight,flexible and kink resistant,black color denotes 4000 psi,low coefficient of friction,excellent cut,gouge and abrasion resistance 4000psi working pressure. Applications: High pressure water cleaning ,lateral sewer lines,water jetting equipment,not for hydraulic applications.
Construction: Tube:Oil resistant synthetic rubber. Reinforcement:Four tensile steel wire spiral layers. (DN10/12/16/19/25) Six tensile steel wire spiral layers. (DN32/38/51) Cover:Black, abrasion and weather resistant synthetic rubber. Temperature range: -40° C to +121° C Application: Heavy duty impulsive high pressure hydraulic applications like excavators, dosers, dumpers, cranes, compactors, rock breakers and hydraulic drill rigs and other construction equipments. Suitable for petroleum based hydraulic fluids, synthetic esters, biodegradable hydraulic fluids, water-glycol based fluids and air.
Construction: Inner Tube:Oil resistant synthetic rubber. Reinforcement:Two high tensile steel wire braid. Cover:Abrasion and weather resistant synthetic rubber. Temperature:-40C~+125C. Application: Mining, metallurgy, petroleum, construction machinery and chemical industry.
Construction: Inner Tube:NBR, Black, Smooth. Reinforcement:Fine wire reinforced, Electrically conductive. Cover:Synthetic Rubber. Temperature:-20 C to +45 C. Feature:Conveying medium: Industrial water, waste water, seawater and irrigation inagriculture. Character: The hose has dual performance that is able to bear positive & negative pressure, it is able to work freely under the vacuum-80kpa(600mm mercury column), without flat& delamination, has good flexural property. The rubber body is flexible, the burst pressure is at least treble than working pressure.
Construction: Inner Tube:Oil resistant synthetic rubber. Reinforcement:Two high tensile steel wire braid. Cover:Â Abrasion and weather resistant synthetic rubber. Temperature range:-40 C to 120 C. Application: Double wire braid: Recommended for hydraulic system service with petroleum and water-base fluids, or general industrial service. Long-lasting cover is suitable for many mobile hydraulic applications. Meets or exceeds all SAE 100R2 AT hydraulic hose specifications.
Construction: Inner Tube:Oil resistant synthetic rubber. Reinforcement:One high tensile steel wire braid. Cover: Abrasion and weather resistant synthetic rubber. Temperature range:-40 C to 120 C.
Rotorless Rheometer MR-C3 The curves and characteristic parameters on vulcanization of rubber material can be obtained using Rotorless Rheometer based on the measurement of the torque exerted by the rubber material on the oscillating die. The MR-C3 Rotorless Rheometer has excellent property of reappears and stability. In a test with good mixed rubber and the time range is 12min, the T90 may be several second difference in 4 continual experiments. Technical indexes Range of temperature control: from room temperature to 200? Temperature fluctuation in die: =±0.1? Temperature display resolution: 0.1? Range of temperature increase: 32?/min Measurement range of torque: 0-300dNm Torque resolution: 0.01dNm Angle of die oscillation: ±0.5°,±1°,±3° Frequency of die oscillation: 1.67Hz(100r/min) Size: 520*570*1000mm(W*L*H) Weight: about 120KG Power: AC220~230V,50/60Hz,3A
Product description Model no: jsj95/200 The first stage l/d ratio: 32:1 The second stage l/d ratio: 9:1 Price: 136666 usd/set The first stage power:260kw The second stage power:80kw Screw diameter: 92/200 Screw speed: 500/85 Capacity: 1000-1200kg/h Packing: wood case or according to requirement Certification: sgs, ce Features: 1.Low maintenance, robustness, durable finish standards, excellent functionality 2.High-efficient force-feeder ensures high capacity feeding, low energy consumption 3. Our machine has two characteristics: high degree of automation and assembly line work. 4.The pelleting machine has good dispersion effect. 5.The machine production is very high, and the work environment is very clean. 6.The technology can be adjusted according to customer's raw material. Type Diameter(mm) L/d Screw speed(r/min) Motor power (kw) Capacity(kg/h) Jsj52/100 50.5 28-40:1 500 45 150-250 100 7-12:1 85 37 Jsj65/150 62.4 28-40:1 500 55-75 500-700 150 7-12:1 85 45-55 Jsj75/180 71 28-40:1 500 90-110 750-900 180 7-12:1 85 55-75 Jsj95/200 92 28-40:1 400-500 250-315 1000-1200 200 7-12:1 85 75-90
Product description Model no: js75b Price: 52666 usd/set High speed machine: 500l Twin single motor diameter: 71mm Main motor power: 132kw Weight: 29.8t Extrusino width: 1800mm Extrusion thickness: 0.8-6mm Capacity: 450-750kg/h Screw l/d ratio: 32-64 Diameter: 71mm Screw rotating speed: 600rpm/min Main motor power: 110-132-160kw Screw torque: 995n.M Torque rating: 4.6t/a2 Packing: wood case or according to requirement Certification: sgs, ce Features: 1.Low maintenance, robustness, durable finish standards, excellent functionality 2.High-efficient force-feeder ensures high capacity feeding, low energy consumption 3. Our machine has two characteristics: high degree of automation and assembly line work. 4.The pelleting machine has good dispersion effect. 5.The machine production is very high, and the work environment is very clean. 6.The technology can be adjusted according to customer's raw material. Model Volume Screw diameter Main motor(kw) Weight T Width mm Thicknessmm Capacity (kg/h) Js65b 300l 62.4mm 75 =19.5 =1000 0.8-6 200~320 Js75b 500l 71mm 132 =29.8 =1800 350~680 Js95b 800l 91mm 185 =39.4 =2150 800~1100
Extruder:EPDM sheet extrusion machine,EVA interior sheet extruder,Rubber sheet extrusion machine,such as rubber and plastic sheet extrusion machine. Features: 1.The characteristics of the machine is advanced design, high quality, good plasticizing and low energy consumption. 2.It has the advantages of low noise, smooth operation, large loading and long life. 3.The technology can be adjusted according to customer’s raw material.
Product Description Rubber floor tile vulcanizing press machine 1- Name: Rubber Vulcanizing Press, Plate Rubber Vulcanizer, Plate Rubber Vulcanizing machine, Rubber Vulcanizing Machine, Vulcanizer, Lab vulcanizing press, Rubber hydraulic press, Plate curing press, Rubber vulcanizing machine, Rubber vulcanizing machinery. 2-Use: This vulcanizing machine is used for all kinds of vulcanizing mould, rubber and plastic mould products, and non-mould products. 3-Main Features: A.Being a column structure and downward pressing type, the heating plate opens by the self-weight of the heating plate, platform and plunger. The rising of the plunger makes the heating plate close while the hydraulic oil provides the pressure. B.The engine base is combined together with the cylinder and base frame, which is made of ductile iron to increase the cylinder intensity and a brad ability. The cylinder is fitted with the sealing washer made of the oil-resisting rubber for the sealing purpose. C.By moving the operational handle of the control valve to the two different positions, the heating plate can open and close. D.It uses the electric pipe for heating, thus makes the workshop clean with easy and reliable operation. Packing: Exporting standard(wooden box packing) Delivery time: 30 days after receipt deposit Payment Term: TT 30% deposit 70% balance payable within 3 days once received the copy of shipping docs(CI,PL&BL) Or L/C at sight with irrevocable
Rubber Screw Types: You can choose different structures of the screw according to different plastic material, which can increase the plasticizing effect, such as gradual, mutant, wavy, double-flight, distributary, separating, exhausting, pin type, mixed ,etc.
Model Length Of Roller Diameter of Roller Motor Power Production Capacity ZP200*600 200mm 600mm 7.5kw 0.8t/h ZP300*600 300mm 600mm 15kw 1.2t/h ZP350*600 350mm 600mm 18.5kw 1.8t/h ZP350*700 350mm 700mm 30kw 3t/h ZP450*760 450mm 760mm 37kw 4t/h ZP510*760 510mm 760mm 45kw 6t/h ZP560*760 560mm 760mm 55kw 8t/h ZP610*760 610mm 760mm 75kw 10t/h Function       The machine is used for dewatering and pressing the rubber material into crepe sheet. We can use one creper in family workshop and several in production line as well. Work Principle       This machine consists of a pair of rollers with diamond groove, rack and transmission system. By the relative movement of the front&back rollers, the machine presses and flattens the raw material, dewatering the rubber and removing the impurities. Due to different speeds between the two rollers, the raw material is pressed to crepe sheet with honeycomb surface. The machine is very easy to operate and is with the features of compact structure, high efficiency, low noise and low power consumption etc.
