Sublimation Coating Spray Liquid

Sublimation coating with acrylic-polyester nature ( in concentrate form ) for sublimation to wood and plywood. Other adhesives with 2 or more components, the mixture of they must be used within 4-5 hours. Unlike these, this concentrate does not mix with other components and is ready for use, can be used whenever needed even in small uses. This makes it economical. This is very easy to use it, with paint brush or paint roller . Sublimation coating with acrylic-polyester nature in paste form (concentrate). The concentrate is ready for use. For the decoration of different wood materials, such as wood board and plywood, through sublimation

Screen printing coating for sublimation on cotton. Recommended mesh number: 90 mesh - 110 mesh Drying with air (ventilated) kiln at 120-140 degrees Celsius (or hair dryer at medium temperature). The process is sample: 1. Print the coating 2. Dry (recommended ventilated kiln) 120 - 140 degrees Celsius for 2-3 minutes (or hair dryer in medium heat, or room temperature for 24 hours) 3. Sublimation at 180 - 182 degrees Celsius ( 355-360 F ) for 30-40 sec.

Theaoson zinc coating spray is composed of aerosol can, aerosol valve, paint liquid and propellant. This product uses bright silver powder imported from Germany. The color of the paint film produced after use has the same high-gloss galvanized color as the galvanized parts, it has the same color as the galvanized color that fades with the exposure time, so that there is no color difference in the repaired part coated on the galvanized part.

This product has good rust resistance and decorative products, color appearance and corrosion resistance of hot dip galvanizing similar, far more than ordinary silver paint. Strong adhesion, good weather resistance, easy to use, is a new decorative material corrosion. Advantage: Good rust resistance/color appearance and corrosion resistance of hot dip galvanizing similar/far more than ordinary silver paint/ Strong adhesion/good weather resistance/easy to use/ is a new decorative material corrosion. Suitable Range: Steel and iron exposed to corrosive conditions.

Premium, liquid applied, highly permanent elastic cold applied one component polyurethane membrane used for long lasting waterproofing. (white/grey color). Other colors possible on request. Supply from Jebel Ali Port thru UAE based manufacturer. Available in 20Kg Pail. Supply in customer's packing/design possible subject to minimum order quantity. Also available, Top coat Liquid PU coating (White-UV reflective). Price available on demand. Also available, Liquid PU coating in Black Color (Wet areas waterproofing). Price available on demand.

Introduction Pure Zinc & Zn/5Al are excellent material choices for corrosion protection in both atmospheric and marine environments. Using either the electric arc spray or combustion wire process, wire coatings of these materials act as sacrificial anodes, galvanically protecting iron or steel substrates.Decades of field work using these coatings has clearly demonstrated that they are far more effective and longerlasting than hot dip galvanizing. Coatings of ZnAl often have better corrosion resistance than either pure zinc or aluminum, by combining the advantages of both materials. This is particularly true in areas where crevices exist and residual moisture and contamination is present, and in areas where the coating has been scratched or scraped, resulting in coating voids and exposed substrate. Using the electric arc spray process, coatings of these materials are often used in the electronics industry for EMI and RF shielding, or as conductive coatings on capacitors. Typical Uses and Applications Atmospheric and immersion corrosion protection on large steel or iron structures such as bridges, roadway barriers, posts and poles, offshore structures and marine structures. Atmospheric corrosion protection on steel or iron components such as tanks and gas bottles EMI and RF shielding on plastic components (electric arc spray only) Electrical conductance on components such as the Conductive areas on insulators and capacitor end caps Product Details Chemical composition: Type Chemical composition Zn Al Others Zn 99.9+ Balance 0.1 Zn 15Al Balance 15 Specifications Grade AWS Zn C2.25/C2.25M W-Zn-1 Physical Properties Grade Density Rockwell Hardness Zn 7.14 g/cm3 ZnAl 7.18 g/cm3 Typical Deposit Characteristics: Grade Typical Hardness Bond Strength Deposit Rate Deposit Efficiency Machilityineab Zn HRB 20 - 30 6.9 - 15.0 Mpa 24 lbs /hr/100A 0.7 Good Zn 5Al HRB 40 -45 20.7 - 24.1 Mpa / / Good Standard Sizes & Packing: Diameter Packing Wire Weight 1/16 (1.6mm) D 300 Spool 15kg((33 lb)/spool Other sizes can produced based on customers' requirement.

This product is made up of anti-alkali primer, modeling aggregate, colored primer, top coat for main material and water-based finishing paint, anti-alkali primer of which intensifies adhesion between this kind of art coating and substrate, reduces water absorption to substrate and prevents salt and alkali from separating. Main material of liquid granite may form color, pattern, crystal section and stereoscopic texture, which can reach adequate hardness. The coating is endowed with physical and chemical property of high weather resistance. Water-based finishing paint is situated at outmost part of coating system possessing hydrophobic nature & ventilation, anti stain, ultraviolet-ray resistance, anti-mildew & anti-alga etc. Finishing coat adopts liquid granite which may be blended with different colors to satisfy various architecture demands from different customers. It has quite good elasticity, comparative smoothness on surface, non-containing gravel and perfect simulation effect. The coating is perfect water resistant, stable dyeing, non-blushing, non-color difference, high decorativeness, high weather resistance, excellent insulation and energy saving etc. It also complies with national insulation & fire protection standard. Finishing coat: inorganic fiber board (thickness: 8mm, 10mm and12mm to be selected and to manufacture according to requirement details) Insulation course: extruded board (mineral wool board/polystyrene board/polyurethane and core material to be made as per design requirement) Selective thickness of insulation: designed thickness Substrate: inorganic resin board Specification: 600 x1200 (to manufacture according to requirement details) Fire protection: a class/ b1 class Installation method: bonding + anchoring -

The series of products are made of saturated carboxylpolyester resin, TGIC or HAA, rutile titanium dioxide ,which are the main raw materials.They have good UV resistance and play a good protection and decorative properties for the application of outdoor metal workpiece surface.