1 Introduction
Iron Based Nano crystalline Ribbon is composed of Fe, Si, B, Nb, and Cu etc.
Iron based amorphous alloy including Cu and Nb element can be formed into crystallite with size in 10-20nm above crystallization temperature through particular annealing treatment. The crystallite material is defined as Nano crystalline alloy.
2 Application
EMC common mode and differential mode filter inductor cores;
switching-mode power supply transformer cores;
current mutual sensor cores (zero sequence, leakage protection);
Magnetic amplifier, spike killer core, saturable inductor core;
3 Feature
High saturation flux density, high permeability, low coercivity, Low loss, good stability, high strength and corrosion resistance, can replace silicon steel, permalloy and ferrite as ideal material for transformer, mutual inductor, its components, has the highest PQ ratio.
Performance Advantages & Feature
R High saturation flux density-- to reduce winding turns, minimize product size
R High resistivity, low coercivity--to improve production performance
R Low loss(1/3 to 1/5 of silicon sheet)--to cool temperature, improve efficiency
R Low excitation--decrease no-load current, and noise
R Adjustable permeability--adopt different heat treatment process according to different requirement
R High temperature stability--long-term operation under 130° C
Description : Plastic-bonded magnets are particle composites with permanent-magnet powder embedded in a plastic binder. Hard ferrite (HF), various SmCo and NdFeB powders and, to a very little extent, AINiCo alloys are used as magnetic powder. For embedding the magnetic particles, thermoplastic binders as, for instance, polyamide (PA) or polyphenyl sulfide (PPS) and duroplasts like epoxy resins are used. Depending on the material composition and production process, isotropic and anisotropic magnets with differing magnetic and mechanical specifications are available. Since not only the type of magnet or plastic material, but the filling and alignment degree, too, determine the composite`s properties, the outcome is widely varying magnetic parameters and an outstanding variety in types and shapes.
Magnetic Writing and Drawing Board Material: ABS+ Magnet
The Incinerated scrap or E46, is the by-product derived from the reprocessing of incinerated domestic waste. After the combustion process, the furnace output (IBA Incinerator bottom ash) is firstly washed, magnetically separated and screened to separate any no ferrous material. At a visual inspection, the material is fragmentized, with iron and steel parts, resulting partly cut or in shredded form. The stock appears heterogeneous and contains all kind of cut or dismantled steel parts such as sheets, bars, frames, wires, bolts and other iron/steel household residues. The incinerated scrap is eventually oxidized, due to the thermal and cooling treatments, that the material has been submitted to. The burnt scrap also contains minor slag parts, ash and iron oxide, due to the recovery process. Such components are inherent and adhere to the scrap surface. The total impurities, can be sorted, but not fully removed. The consignment does not contain any type of arms, ammunition, mines, shells, cartridges, radioactive contaminated, or any other explosive material in any form either used or otherwise. The collected stock, is stored in open air, on cemented flooring. It can be loaded loose in 20â?? heavy duty container. Please feel free to contact us for further details.
We, nanjing herui international co., ltd., is trading company of herui group, which are mainly exporting magnetic materials produced by our plant located in nanjing , china. Our magnetic materials including magnetic powder, ferrite magnet(hard and soft), magnet strip. Such as : segment, ring and cylindric magnet , Square and bar magnet , square magnet with hole , Based on y30h-1, y30h-2, y33, y35 Segment magnet Wet press segment magnet is our main product with 3000 tons capacity. The magnets are mostly used in automotive(such as wiper, window lift, blower, abs, seat and fuel pump motors), motorcycle, electric-tool, fitness equipment and home appliance etc.Produce by powder metallurgical method , chemical composition of sro6fe2o3 , relatively brittle & hard , good resistance to demagnetization , excellent corrosion resistance , good temperature stability , raw material is readily available & low in cost. Pigment: Our company also able to export pigment from china for paiting and coating. Which used in wall&road painting , ground tile, etc We can provide you iron oxide red, iron oxide yellow, iron oxide green, iron oxide black. The most important is we can produce any kind of color and grade as per your instruction. We can produce purely same products as per your counter sample and stardard. - Wooden carton
SOFT MAGNETIC ALLOY - HYMU 80 : (Composition (Nominal) 0.02 C, 0.50 Mn, 0.35 Si, 80.00 Ni, 4.20 Mo, Bal. Fe ; ( HYMU 80 is an alloy of nickel, iron and molybdenum. It is a soft magnetic alloy with exceptionally high magnetic permeability. The alloy has a low coercivity, near zero magnetostriction, and significant anisotropic magnetoresistance. The low magnetostriction is critical for industrial applications,where variable stresses in thin films would otherwise cause a ruinously large variation in magnetic properties. ) : (SPECIFICATION :ASTM A753 ; (Product availability and request a QUOTE!
SOFT MAGNETIC - IRON COBALT ALLOY VACOFLUX 48 is an iron-cobalt-vanadium soft magnetic alloy which exhibitshigh magnetic saturation, high D.C. maximum permeability, low D.C. coercive force, and low A.C. core loss.; ; (1.SPECIFICATION: ASTM A801 Alloy Type 1, :) ;; ( 1.Coericivity for cold rolled strip possible Hc,no more than(A/m) 60 ;; ( 2. Coercivity for forging rod possible HC,No more than (A/m) 80 ; ;( Product availability and request a QUOTE!
HIPERCO 50A:Composition (Nominal):Fe49,Co49,V2 :)---Hiperco 50A Alloy is an iron-cobalt-vanadium soft magnetic alloy which exhibits high magnetic saturation (24 kilogauss), high D.C. maximum permeability, low D.C. coercive force, and low A.C. core loss.:)---Specifications: ASTM A801 Alloy Type 1, MIL A 47182
Magnet materials: 1)ndfeb material(sintered and bonded) 2)hard ferrite(sr ferrite and ba ferrite) 3)smco(1:5 and 2:17) 4)alnico(casting and sintering) 5)rubber magnet 6)soft magnet(mn-zn and ni-zn) 7)injection magnet(ndfeb and ferrite) Surface treatment: 1)plating (ni, zn, cr, cu, ar¦.) 2)coating(epoxy resin) 3)spray coating(epoxy resin) 1. Bonded ndfeb magnets 2. Sintered ndfeb magnets 3. Ferrites > sintered hard ferrite > soft ferrite-mnzn ferrite > soft ferrite-nizn ferrite 4 smco magnets 5 cast and sintered alnico magnets
Electrical steel is a soft magnetic material with enhanced electrical properties that is widely used across applications such as small relays, solenoids, electric motors, generators, and many other electromagnetic devices. Electrical steel is also referred to as silicon steel, transformer steel, or lamination steel For price, specifications and other details please contact us
