E1403706C00 Throat Guide

HYDRAULIC PRESS BRAKE MACHINE We Have Been Manufacturing A Wide Range Of Hydraulic Press Brake Machine. These Machines Are Easy To Install And Requires Low Maintenance. We Develop These Machines With The Aid Of Latest Technology, So That The End Product Conforms To Set Industry Norms. FEATURES : Repetitive accuracy is within 0.03 mm. Three cycles of operation. Inch-single-continuous cycles for greater operator convenience. Full powered stroke make machine suitable for general sheet metal press work. Three speeds reduce idle travel time, improves productivity. Instant ram stoppage prevents accidents and job rejections. Noiseless operation and least impact loads on tools and foundations. Less power consumption, least wear and maintenance reduces operating costs and down time. DESIGN FEATURES Mono Block Welded Steel Frame ultra tested-2062 steel plates rigid to provide accurate bending. All pivots have been hardened of ground pin bushes of five piece guide slide lubricated by central hand pump. Repetitive accuracy is within �± 0.03 mm Ram travel parellelism without sensitive & complex servo hydraulics. Most reliable hydraulic components & sealing for international reputed design for 350 bar against operating pressure of 160 bar maximum. Three cycles operation inch, Single cycle & Auto for greater operator convenience. Three speed operation reduces ideal travel time which improves productivity. Bending force easily adjustable from front for forgue tools of bending soft material. Movable operator console is provided with switches for cycle selection, ram up-down travel, emergency stop & motor on/off. Manual backstop with micro adjustable swing stop facilitate reverse bend. Electrical panels & components are provided as per international reputed brands. Precisely designed of manufacture cylinders provided unlimited trouble -free life. Seals can be changed quickly without dismanting the ram or need of crane. STANDARD FEATURES & ACCESSORIES Main drive standard make motor. Electrical control panel with three speed inch, Single cycle, Auto mode of operation. Two front sheet supports. Manual back gauge with micro-adjustment swing stoppers. Pair of lifting chains. Fine stroke adjustment rod with limit switches. One suitable 5-way die and blade. (Segmented or full length, EN-9 not covered under warranty). Movable console with emergency device. Manual centralized lubrication system with hand pump. Bending chart. OPTIONAL ACCESSORIES Ram tilting arrangement. Motorized back gauge with DRO. Extra Finger for standard Back gauge. Automatic Lubrication System. Extra Depth of throat.

Introduction APEC Brand AIW series Hydraulic Ironworker is widely used in steel structure, high voltage tower, telecommunication tower, large rigid frame bridge, military and air craft and other metal fabricating industries. It also can be used in vocational school for teaching purpose. APEC Brand AIW series Ironworker features multiple functions, including: punching all kinds of holes (round hole, square hole, oblong hole), louver punching, steel plate punching, flat bar punching, angle steel punching, C-channel punching, H-beam punching, I-beam punching, profile steel shearing (channel shearing, I-beam shearing, round/square bar shearing, flat bar shearing, T-bar shearing, steel plate shearing, angle steel shearing), notching, press brake, angle steel notching , bending, pipe notching. It comes standard with: quick-change coupling nut & sleeve, squaring arm with scale, electronic back gauge, gauging table with stops, punching base table, safety guards and more.We can design any special tools according to your metal fabricating requirements. APEC Brand AIW-E series is improved machine on the base of standard AIW series. It goes along with automatic holding system and temperature cooling system. Automatic Holding System: There is automatic holding system in angle steel shearing and plate shearing work position. The holders will fix the position of work-piece, in this way, the accuracy is better and more safety for workers meanwhile save time and Improve working efficiency. Temperature cooling system:Through the temperature monitoring screen you can read the temperature of oil, 55 degree is our default configuration, once the machine is working, oil temperature goes higher than 55 degree, the cooling system inside will run automatically to decrease temperature in order to protect machine. APEC Brand AIW-L series is improved machine on the base of standard AIW-E series. It also goes along with automatic holding system and temperature cooling system. At the same times, punching position and shearing position can work synchronously. Features 1. High Quality Components & System a. Main Electrical component: Schneider, Germany. b. Valve: Yuken, Japan c. Pump: Atos, Italy d. Oil Seals: NOK, Japan e. Timer Relay: OMRON, Japan f. Wiring Terminal Block:WEIDMULLER, Germany g. Motor: Weiteli, China 2. Cost Effective AIW SERIES Hydraulic Ironworker With Very good price/performance ratio Various AIW SERIES Hydraulic Ironworker capacity from 45T to 400T to meet your requirement. 3. Stable Performance & Reliable Quality AIW Series Hydraulic Ironworker use hydraulic transmission. Light weight, low noise, reliable performance. 4. Simple Operation The operation of hydraulic ironworker is controlled by foot switch. Technical Parameters: Accessories: a. A pair of round hole punching die b. A set of angle steel blade c. A set of square and round bar blade d. A set of shearing plate blade e. A set of notching blade The above punching and moulds will be installed in the machine. For other dies and blades, customers need to order Installation & Operation Training APEC will provide you 1-7 day installation and operating training in our factory. Training After-sales service 1. Technical documents All labels on machines and lay-out drawings, Electrical diagram, Operation Manual, will be in English. The seller should send all necessary files to the buyer since the third week since project execution. All documents in hard copies should be also shipped with machines together. 2. Arrangement for inspection, installation and testing work a. After all machines are delivered to customer¡¯s factory; Buyer is responsible for all preparation work, e.g. electricity supply, water supply, labors and cranes, etc. b. The buyer will prepare for visa application for their engineers, who are responsible for guide of machine installation and testing at the Buyer¡¯s factory. c. The Buyer will buy the round-trip air ticket for Engineer if visa application is approved. The buyer is also responsible to bear expenses generated, e.g. visa formalities, meals, accommodation and allowance of USD80 per day for each engineer. d. Engineer will give free training lessons to labors in buyer¡¯s factory. 3. Quantity and quality guarantee a.Quantity/Quality Discrepancy to destination port during transportation: In case of quality/quantity discrepancy to destination port in transportation, the buyer should file claim within 30 days after the arrival of the goods at port of destination. The seller will not be responsible for any discrepancy of the goods caused by shipping company and other transportation organization and/or post office. b.Guarantee period and after-sales services: 13 months since date of bill of lading During this guarantee period, the seller will provide spare parts without any charge in case of quality discrepancy caused by us. If the malfunctions are caused by your incorrect operations, the seller will provide the buyer spare parts at cost price. c.Long-term service: The seller will charge the buyer cost price of spare parts beyond one year and provide long-term technical guide. FAQS: 1. Payment Terms T/T, L/C at sight are acceptable by us. 2. Price Terms It is up to your requirement. EX-WORS, FOB, CIF, CFR and so on are acceptable by us. 3. Delivery Time 25 working days from our accountant confirm your deposit payment. 4. Shipment Condition We will arrange the machine production from our accountant confirm your deposit payment. The deposit is 30% of the contract. The balance should be paid up before loading machines. 5. Warranty 13 months quality guaranty for the main spare parts, not include quick-wears parts, like blade, punch, die and so on. If the parts of machines have problems, which are caused by its own quality, we will provide the accessories for free. General View of machine Mutiple Functions Machine pictures Work pieces Hydraulic ironworker, ironworker, lathe, punching, cutting, notching, bending, machine, process, metal steel, plate cutting, Angle cutting, plate bending, shearing, hydraulic ironworker machine, mechanical ironworker, ironworkers, iron worker, steel worker, metal worker, shearing machine, cutting machine, sheet metal punching machine, notching machine, guillotine machine, bending machine, press brake, c-channel bar cutting machine, H-beam cutting machine, angle bar cutting machine, dual hydraulic cylinders, single cylinder, punch and shear station, rolling machine, band saw, pipe punching, tube bending, pipe notching, machine tool. Model AIW-60/L(Q35Y-16) AIW-90/E/L(Q35Y-20) AIW-120/E/L(Q35Y-25) AIW-160/E/L(Q35Y-30) AIW-200/E/L(Q35Y-40) AIW-250/E/L(Q35Y-50) Processing Capacity (KN) 600 900 1200 1600 2000 2500 Material Tensile Strength (Mpa) ¡Ü450 ¡Ü450 ¡Ü450 ¡Ü450 ¡Ü450 ¡Ü450 Ram Stroke(mm) 80 80 80 80 100 100 Number of Stroke(times/min) 8-22 8-22 8-22 8-22 8-24 8-24 Throat Depth 300 355 400 600 550 550 Shear Angle 7¡ã 8¡ã 8¡ã 8¡ã 8¡ã 8¡ã Flat Shearing Max. Shearing Capacity (thickness* width (mm) 16¡Á250 20¡Á330 25¡Á330 30¡Á355 35¡Á400 40¡Á450 8¡Á400 10¡Á480 16¡Á600 20¡Á600 25¡Á700 30¡Á750 Bar Shearing Square Bar(mm) 40 45 50 55 60 65 Round Bar (mm) 45 50 60 65 70 80 C-channel (mm) 126 160 200 280 300 320 I-beam (mm) 126 160 200 280 300 320 Angle shearing 90¡ã shearing (mm) 120¡Á12 140¡Á12 160¡Á14 180¡Á16 200¡Á18 200¡Á20 45¡ã shearing (mm) 70x8 70x10 80x7 80x10 80x10 80x10 Hole Punching Max. Punching Capacity (diameter* thickness) (mm) ¦µ25*16 ¦µ30*20 ¦µ35*25 ¦µ38*28 ¦µ40*35 ¦µ40*40 Motor (KW) 4 5.5 7.5 11 15 18.5 Dimension(mm) Length 1650 1950 2350 2680 2800 3200 Width 800 900 980 1060 1260 1440 Height 1780 1930 2100 2380 2420 2450 Weight 1800 2600 4800 6800 9200 12800

Z03050900023AA Guardrails 644302499 Frame grease lubricated Casing Power Tong TQ340/35 Receiver TZS-K(JS) oil seal 5300200066 https://www.amlppmfg.com/sbr3570cc-02-upper-shear-ram-block.html ZQ203-125 oil drain line assembly 01.08.12.00M �?�¾�¼�¿�»�µ�º�? �¿�?�¾�º�»�°�´�º QF36001-02.17 FKQ8007 Anti-seismic pressure transmitter YPQ-250B ZQJ300*2-1.6*0.6 Desander Right Cyclone bracket pin DQ70BSD 9703642012 IA191-(P-059331-0000) Two-position three-way valve FQN24-10ZK ten-pin aviation plug (female) 78910-2 RTV,162 WHITE 10.3 OZ, C/W MSDS Rotary joint 4700650114 Driller Valve HD-2-X/P050973-1/IA295 Pneumatic control valve BK-F-W4 P981120140AA Channel steel L=514 SL450Flushing assembly SpacerII AA4501230905 Cable transport frame 1.16.07.01.001 Derrick cage\ZJ50 AQL.07.06 IA341Regulator FKQ6406-G steel ball seat 9160600007 Faucet SL450-5 collar 104.07.06.21 3.03.02.12.011 Electrical connector 2.4.34.074 connector QBJ10010302 NPT3/8"X1/4" bushing R431006327/P63985-1/7P-9S Rexroth valve Lubrication system F-1600HL oil filter assembly AH100101061000 Density meter level assembly XYM-5-1 XYM-5 density meter Impeller FMC15145ELA05 low pressure filter FKQ640-6DLQ-00-00 FKQ relief valve Y-25-20C Drain valve IA-193 Inner retaining ring DQ70BSD 9702020212 pin P2000669AA Manual pressure regulator ArCOO 0.05-0.85MPa safety slip WA-Csafety slip 13-1/2"~14-5/8" WA-C-011 Z04220200001AA Bolt, grommet retaining ring BK-7-7A9 FH4147 Impeller �° DSQ-01.00 4900300057 Water draining valve 70-30 High pressure plug valve 2"1502M*2"1502F/1 Disc brake emergency cylinder BG-00C CLUTCH ATD330H Hydraulic tubing pliers (power pliers) XQY-150/12 Nitriding block Q12.1 R431003807/P55556-4/8P-1S Rexroth valve filter element ZJ70D DLX9048 325Q10 Faucet SL125 flushing pipe assembly RI40391132-04 Power selection box 40-17 check valve oRing DQ70 2.4.51.031 Turntable ZJ-45 driller operation box 106.02.300.00 Boiler RL70 Boiler computer controller YLZK-C5 Bushing BKD-3-6D3 Frame plate liner insertF6041HS1A05 exhaust elbow 9Y2151 Vent 512604900000030801 Connector DQ70 3.03.03.04.001 gap adjuster9261914exhaust valve guide 197-6995 RADIATOR; Part Number: 5199000030; Gasket AH0801010203 Winch oil pump transmission shaft ZJ50D/3150 oil pump device (left-handed) AF400109-1201 Connector Assembly 154-5559filter element 9M2342 ZQ203-100 screw 16*20 FKQ12808BS relief valve Y-25,20C Dwyer 1910-1 Air Pressure Switch Gasket AH0801010415 Rubber Throat bush F6083R55 hydraulic valve\ZJ70D 4WEH16T50B/6EG24NEZ4 Pressure switch JDW 5 Inclinometer GE-MWD Probe upper end line plug 981992 air filter drain cup FKQ640-6 Well gauge YDTJ 140*2m Rubber mat EK140103-010131 4.10.09.009 Elastic washer Lubricator QYW-L15-S1 disc brake block JC-70B

The BEND MASTER Series has been redesigned for enhanced user experience, featuring advanced electronic and mechanical hardware. This series provides exceptional results for standard, stainless, thin, and thick sheets. Standard Configuration CNC Motorized Crowning (3 m & above) 4-Axis Back Gauge (X, Z1, Z2 & R) CNC Touch Screen Controller Quick/Smart Clamps 2 Fingers on Back Gauge 2 Front Supports on T Slot Options Back & Side Safety Doors/Laser Light Curtains 6-Axis Back Gauge Controller Options (ESA, DELEM, CYBLEC) Additional Foot Pedal (for models >4 m) Front Supports on LM Guide Rails Bending Tools (as per selection) Front & Back LED Lights Laser Finger Safety Customization in Daylight, Stroke & Throat (100 mm increments) Offline Programming Software (per controller compatibility) Laser Angle Measuring & Correction System Choice of Tooling (2V or Single V Type) Hydraulic Oil Cooler (for 200T & above) Ready for Robot Integration AC for Electric Cabinet Tandem Configuration Model Specifications Model 5015: 50T, 1500mm length, 400mm daylight, 270mm throat. Model 5020: 50T, 2100mm length, 400mm daylight, 320mm throat. Model 8025: 80T, 2500mm length, 450mm daylight, 320mm throat. Model 11025: 110T, 2500mm length, 500mm daylight, 400mm throat. Model 11032: 110T, 3200mm length, 500mm daylight, 400mm throat. Model 11041: 110T, 4100mm length, 500mm daylight, 400mm throat. Model 13032: 110T, 3200mm length, 500mm daylight, 400mm throat. Model 13041: 135T, 4100mm length, 500mm daylight, 400mm throat. Model 13051: 135T, 5100mm length, 500mm daylight, 400mm throat. Model 17032: 135T, 3200mm length, 500mm daylight, 400mm throat. Model 17041: 170T, 4100mm length, 500mm daylight, 400mm throat. Model 17051: 170T, 5100mm length, 500mm daylight, 400mm throat. Model 17061: 170T, 6100mm length, 500mm daylight, 400mm throat. Model 22032: 170T, 3200mm length, 500mm daylight, 400mm throat. Model 22041: 220T, 4100mm length, 500mm daylight, 400mm throat. Model 22051: 220T, 5100mm length, 500mm daylight, 400mm throat. Model 22061: 220T, 6100mm length, 500mm daylight, 400mm throat. Model 25032: 220T, 3200mm length, 550mm daylight, 400mm throat. Model 25041: 260T, 4100mm length, 550mm daylight, 400mm throat. Model 25051: 260T, 5100mm length, 550mm daylight, 400mm throat. Model 25061: 260T, 6100mm length, 550mm daylight, 400mm throat. Model 32032: 260T, 3200mm length, 600mm daylight, 500mm throat. Model 32041: 320T, 4100mm length, 600mm daylight, 500mm throat. Model 32051: 320T, 5100mm length, 600mm daylight, 500mm throat. Model 32061: 320T, 6100mm length, 600mm daylight, 500mm throat.

The Bend Pro Series has been revamped with advanced electronic and mechanical hardware, efficiently handling standard, stainless, thin, and thick sheets. This series features enhanced configurations to meet diverse user needs. Standard Configuration CNC Motorized Crowning (3 m & Above) 4-Axis Back Gauge (X, Z1, Z2 & R) CNC Touch Screen Controller 2 Fingers on Back Gauge Quick/Smart Clamps 2 Movable Front Supports on LM Guide Rails Controller Options (ESA, DELEM, CYBLEC) Back & Side Safety Doors AC for Electric Cabinet Front & Back LED Light Options Customization in Daylight, Stroke & Throat by 100 mm increments 6-Axis Back Gauge (X1, X2, Z1, Z2, R1 & R2) Choice of Tooling (2V or Single V Type) Additional Foot Pedal (Above 4 m) Ready for Robot Integration Laser Finger Safety Height Adjustable Front Supports Offline Programming Software Laser Angle Measuring & Correction System Tandem Configuration Hydraulic Crowning Models Overview Model: 5015 - Tonage: 50, Length: 1500, Daylight: 400, Stroke: 200, Motor: 7 Model: 5020 - Tonage: 50, Length: 2100, Daylight: 400, Stroke: 200, Motor: 7.5 Model: 8025 - Tonage: 80, Length: 2500, Daylight: 450, Stroke: 200, Motor: 11 Model: 11025 - Tonage: 110, Length: 2500, Daylight: 500, Stroke: 250, Motor: 11 Model: 11032 - Tonage: 110, Length: 3200, Daylight: 500, Stroke: 250, Motor: 11 Model: 11041 - Tonage: 110, Length: 4100, Daylight: 500, Stroke: 250, Motor: 11 Model: 13032 - Tonage: 110, Length: 3200, Daylight: 500, Stroke: 250, Motor: 11 Model: 13041 - Tonage: 135, Length: 4100, Daylight: 500, Stroke: 250, Motor: 11 Model: 13051 - Tonage: 135, Length: 5100, Daylight: 500, Stroke: 250, Motor: 11 Model: 17032 - Tonage: 135, Length: 3200, Daylight: 500, Stroke: 250, Motor: 15 Model: 17041 - Tonage: 170, Length: 4100, Daylight: 500, Stroke: 250, Motor: 15 Model: 17051 - Tonage: 170, Length: 5100, Daylight: 500, Stroke: 250, Motor: 15 Model: 17061 - Tonage: 170, Length: 6100, Daylight: 500, Stroke: 250, Motor: 18 Model: 22032 - Tonage: 170, Length: 3200, Daylight: 500, Stroke: 300, Motor: 15 Model: 22041 - Tonage: 220, Length: 4100, Daylight: 500, Stroke: 300, Motor: 15 Model: 22051 - Tonage: 220, Length: 5100, Daylight: 500, Stroke: 300, Motor: 15 Model: 22061 - Tonage: 220, Length: 6100, Daylight: 500, Stroke: 300, Motor: 18 Model: 25032 - Tonage: 220, Length: 3200, Daylight: 550, Stroke: 300, Motor: 18 Model: 25041 - Tonage: 260, Length: 4100, Daylight: 550, Stroke: 300, Motor: 18 Model: 25051 - Tonage: 260, Length: 5100, Daylight: 550, Stroke: 300, Motor: 18 Model: 25061 - Tonage: 260, Length: 6100, Daylight: 550, Stroke: 300, Motor: 22 Model: 32032 - Tonage: 260, Length: 3200, Daylight: 600, Stroke: 300, Motor: 30 Model: 32041 - Tonage: 320, Length: 4100, Daylight: 600, Stroke: 300, Motor: 30 Model: 32051 - Tonage: 320, Length: 5100, Daylight: 600, Stroke: 300, Motor: 30 Model: 32061 - Tonage: 320, Length: 6100, Daylight: 600, Stroke: 300, Motor: 30