This tool is used for protecting workers while they are operating punch or other machines. The tool is made from a metal connector and permanent magnet. What workers should do is just holding the handle, and then put the side of magnet upon the metal parts in the machine, so as to the metal parts will be magnetized by the magnet, finally workers can safely move the parts and press the connector to separate the parts from the tool.
Features:
Increase the chip baffle to effectively prevent iron chips from falling into the water jacket;
Parameter:
Linear velocity Vc(m/min): 450
Cutting tools diameter(mm): 35
Rotate speed (1/min): 4095
Teeth number: 2
Feed per teeth fz(mm): 0.15
Feed F(mm): 1228
Cutting-in Ap(mm): --
Double Side Rail Hole Chamfering Kit
The double chamfer is used for chamfering the holes on the waist of railway rail. The structure of the bilateral chamfering
device: It has a door frame, the left and right holder through a set of four bar linkage hinge, and equipped with upper locking lever handle, install left axle shaft sleeve of the bottom of the left bracket, left axis right side is equipped with disc blade, left left end shaft with a ratchet wrench, right shaft are installed in the shaft sleeve from the lower pole of the right holder, the right shaft suits a compression spring, right left end shaft is equipped with the disc blade, The right end of the right axle is fitted with a ratchet wrench. The double-sided chamfering device has the advantages of simple structure, convenient operation and high working efficiency. The blade is disk-shaped, the blade on the whole circumference is sharp and wear-resistant, and the service life is long.
Specification
Model LJ-DJQ-S
Type Rail Chamfering Tool
Material Stainless Steel
Dimensions (L x W x H) 40*15 cm
Chamfer Diameter �?31-�?32
Chamfering Size 1�?45�°, 2.5�?45�°
Application 43kg/m,50kg/m,60kg/m rail
Weight 2.8KG
Double Side Rail Hole Chamfering Kit
The double chamfer is used for chamfering the holes on the waist of railway rail. The structure of the bilateral chamfering
device: It has a door frame, the left and right holder through a set of four bar linkage hinge, and equipped with upper locking lever handle, install left axle shaft sleeve of the bottom of the left bracket, left axis right side is equipped with disc blade, left left end shaft with a ratchet wrench, right shaft are installed in the shaft sleeve from the lower pole of the right holder, the right shaft suits a compression spring, right left end shaft is equipped with the disc blade, The right end of the right axle is fitted with a ratchet wrench. The double-sided chamfering device has the advantages of simple structure, convenient operation and high working efficiency. The blade is disk-shaped, the blade on the whole circumference is sharp and wear-resistant, and the service life is long.
Specification
Model LJ-DJQ-S
Type Rail Chamfering Tool
Material Stainless Steel
Dimensions (L x W x H) 40*15 cm
Chamfer Diameter 31-?32
Chamfering Size 145°, 2.5 45°
Application 43kg/m,50kg/m,60kg/m rail
Weight 2.8KG
The double chamfer is used for chamfering the holes on the waist of railway rail.
The structure of the bilateral chamfering device: It has a door frame, the left and right holder through a set of four bar linkage hinge, and equipped with upper locking lever handle, install left axle shaft sleeve of the bottom of the left bracket, left axis right side is equipped with disc blade, left left end shaft with a ratchet wrench, right shaft are installed in the shaft sleeve from the lower pole of the right holder, the right shaft suits a compression spring, right left end shaft is equipped with the disc blade, The right end of the right axle is fitted with a ratchet wrench.
The double - sided chamfering device has the advantages of simple structure, convenient operation and high working efficiency.
The blade is disk - shaped, the blade on the whole circumference is sharp and wear - resistant, and the service life is long.
