Single-effect fiber separator is a kind of pulping equipment used in papermaking industry. It is mainly used to separate the heavy and heavy items in the pulp, and the slurry from the water pulping machine is broken down twice.
Structure: mainly composed of base, shell, impeller, bearing frame, cutter plate, sieve plate, etc.
Principle: pumping slurry from the cylinder above along the tangent direction into the separation chamber, the centrifugal force generated by high speed rotating impeller to make pulp do circular motion inside the separator, heavier than major impurities in pulp was quickly rotate to the periphery along the wall, heavy slag into the slag system. The light impurities are concentrated in the center under the action of centripetal force, which is discharged by the outlet of the center front end under pressure, and the good pulp after separating the impurities passes through the sieve plate to the next process.
Purpose: to remove all kinds of impurities from waste paper materials by using the fiber weight difference, which has the function of dredging, separation and coarse screening. It is usually set up as secondary ground pulp and separation equipment after the hydraulic shredder. It can also be used as the finishing equipment for tailings.
Structural features:
It has two basic functions, such as separation of light impurities and heavy waste
Lower waste paper can be used to reduce the pretreatment of raw materials.
The production capacity of existing hydraulic pulper can be improved, and the energy consumption can be reduced by 40-60%.
High quality pulp can be obtained, fiber loss is small, improve screening efficiency, and yield is 2-2.5 times of traditional single effect
Tectonics
1. The cylinder
The cylinder adopts wear resistance and pressure resistance design standard, material is stainless steel or carbon steel. Pulp by entry along the tangent direction into the cylinder, the rotor high-speed rotation of the centrifugal pulp raw material, and the light impurity separation, light impurity by cylinder gland central discharge, heavy impurities by the principle of centrifugal force, along the cylinder tangent into the sand tank.
2. The rotor
The rotor adopts special shape design, which can effectively separate the weight impurities.
The inside of the rotor is equipped with a clean water pipe to prevent the mesh from being blocked.
The rotor blade adopts replaceable high - wear high - wear strength alloy steel.
The rotor body is cast steel or cast stainless steel.
3. The sieve plate
The aperture of sieve plate is 2.5-6mm
Usually newsprint, magazine paper for the use of 2.5-4mm
Corrugated paper, box board paper is 3.5-6mm fan
The sieve plate is assembled in pieces, easy and easy to replace the sieve plate.
The polyester staple fiber machine (PSF plant) takes virgin PET Chips, recycled Bottle Flakes, Popcorn and Lumps, etc., as raw material, with continuous drying (or batch drying through Vacuum Dryer), high pressure melt spinning process engineering and VFD controlled Spinning & Stretching process engineering to produce normal Staple Fibre, High Tenacity Low Elongation Staple Fibre and Hollow Fibre. Single plant capacity is 15T.P.D. to 80T.P.D. Equipment Technical Data Titer Range dtex 6.67-16.67 Spinning Pos. nos. 6-24 Spinning Pitch mm 700, 750 Plant Capacity TPD 15-80 Spinneret dia. mm 328, 358, 410 Spinning Mechanical Speed m/min 500-1,500 Spinning Processing Speed m/min 500-1,300 Stretching Mechanical Speed m/min 240 Stretching Processing Speed m/min 230 Total Tow Titer at Stretching dtex 600,000-3,000,000 Stuffer Box Width mm 160-410 Cutting Length mm 25, 32, 38, 44, 51, 64, 76, 101 Bale Weight kg 200-350 Application: Cushions Pillows Quilts Toys Jacket Mattress Non woven carpet Automotive felts, speaker felts, geo textiles, polyfill wadding, filter fabrics and other acoustics as well. Spinning Line: Continuous Dryer Hopper Screw Extruder Polymer Pipe Filter Spin Beam (Meter Pump System, Spin Pack, Spinneret) Quenching Unit Interfloor Duct Draw-off Wall Capstan Roller Sunflower Gearing Unit Automatic Fiber Can Device Drawing line: Can Creel Inlet Thread Guide Tow Guide Stand Dipping Bath 1st Draw Stand Draw Bath 2nd Draw Stand Draw Steam Chest 3rd Draw Stand Tow Stacker Crimper Steam Box Crimper Silicone Oil Sprayer Machine Tow Tension Stand Cutter Fiber Spreading Machine Relaxer Fiber Blowing system Baling Press
The 5XF-2000-80 Air-Screen Cleaner is a multi-purpose machine with pre-cleaning and sorting unit for mostly commercial crops. The operation of the machine is divided into two parts. In the first screening system with gravity separator, raw materials fall to the screen, then blight seeds are let to fall out using the eccentric shaft generated by the positive air pressure. Desired materials and larger impurities are moved forward to the top of the screen. Larger impurities are discharged from the outlet. Undersized contaminants and soil in materials fall by the next screen, while the desired materials continue to move ahead. Finally, all of the good materials are categorized into specific size dimensions i.e. big, medium and small sizes through grading screens. The cleaning system has elastic balls moving for preventing screen blockages. This product is the most sensitive screening and cleaning equipment with gravity separator and vibrating grader. Moreover, this product is equipped with proprietary elevator for transferring materials to the air screen cleaner, the materials are passed through the screen and cyclone that are attached to the elevator.
Roller Conveyor Shot Blasting Machine for Bright Bars Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 1 Unit Per Month Price And Quantity Price Range 100000.00 - 300000.00 INR/Unit Minimum Order Quantity 1 Unit Product Specifications: Product Type Other Warranty All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Power Source Electricity Operating Type Automatic Usage/Applications Casting, Forging, Sheet Metal Pressure 6-7 Bar Power 420 Volt (v) Color Dark Blue Surface Treatment Painted Technology Other Product Description: TheTunnel type/ roller conveyor shot blasting machine is best suitable for the shotblasting of Round steel Pipes..etc. It consists of inlet and outlet side Rollerconveyors as material handling systems. The components to be blasted are placedon inlet side of the roller conveyor, from where it travels forward and entersinto the inlet tunnel. After passing through the inlet tunnel components entersinto the blast zone which consists of 4 no�?�¢�?â?¬�?â?¢s of Blast Wheels. All these Blast wheel units are strategically placedaround the Blast cabinet. The arrangement of the blast wheel ensures optimum blastcleaning and maximum utilization of the abrasive energy. Blast wheels fires the abrasive at high velocity onthe forward moving components & blast cleans them thoroughly. Blastedmaterial moves forward and enters into the outlet tunnel. The spent abrasivefrom blasting operation after passing through the perforated floor plates willget collected into the cabinet�?�¢�?â?¬�?â?¢s bottom storage hopper. From where it istransferred to the bucket elevator, which elevate the abrasivevertically and discharges the same into a media separation unit where dust andfine abrasives are cleaned ensuring that only clean abrasive will re-circulateto the blast wheel units for effective and better cleaning. A Dust collectionsystem is provided with the machine which will continuously remove the dust andfine particles, thus keeping the inside of the machineand the nearby environment dust & pollution free.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Price Range 1200000.00 - 1500000.00 INR/Unit Minimum Order Quantity 1 Unit Product Specifications: Color Dark Blue Product Type Other Pressure 6-7 Bar Power 420 Volt (v) Power Source Electricity Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Technology Other Usage/Applications Casting, Forging, Sheet Metal Operating Type Automatic Surface Treatment Painted Product Description: It consists of inlet and outlet side Rollerconveyors as material handling systems. The components to be blasted are placedon inlet side of the roller conveyor, from where it travels forward and entersinto the inlet tunnel. After passing through the inlet tunnel components entersinto the blast zone which consists of 4 nos of Blast Wheels. All these Blast wheel units are strategically placedaround the Blast cabinet. The arrangement of the blast wheel ensures optimum blastcleaning and maximum utilization of the abrasive energy. Blast wheels fires the abrasive at high velocity onthe forward moving components & blast cleans them thoroughly. Blastedmaterial moves forward and enters into the outlet tunnel. The spent abrasivefrom blasting operation after passing through the perforated floor plates willget collected into the cabinets bottom storage hopper. From where it istransferred to the bucket elevator, which elevate the abrasivevertically and discharges the same into a media separation unit where dust andfine abrasives are cleaned ensuring that only clean abrasive will re-circulateto the blast wheel units for effective and better cleaning. A Dust collectionsystem is provided with the machine which will continuously remove the dust andfine particles, thus keeping the inside of the machineand the nearby environment dust & pollution free.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Product Specifications: Operating Type Automatic Technology Other Product Type Other Color Dark Blue Pressure 6-7 Bar Usage/Applications Casting, Forging, Sheet Metal Surface Treatment Painted Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Power Source Electricity Power 420 Volt (v) Product Description: It consists of inlet and outlet side Rollerconveyors as material handling systems. The components to be blasted are placedon inlet side of the roller conveyor, from where it travels forward and entersinto the inlet tunnel. After passing through the inlet tunnel components entersinto the blast zone which consists of 4 nos of Blast Wheels. All these Blast wheel units are strategically placedaround the Blast cabinet. The arrangement of the blast wheel ensures optimum blastcleaning and maximum utilization of the abrasive energy.Blast wheels fires the abrasive at high velocity onthe forward moving components & blast cleans them thoroughly. Blastedmaterial moves forward and enters into the outlet tunnel. The spent abrasivefrom blasting operation after passing through the perforated floor plates willget collected into the cabinets bottom storage hopper. From where it istransferred to the bucket elevator, which elevate the abrasivevertically and discharges the same into a media separation unit where dust andfine abrasives are cleaned ensuring that only clean abrasive will re-circulateto the blast wheel units for effective and better cleaning. A Dust collectionsystem is provided with the machine which will continuously remove the dust andfine particles, thus keeping the inside of the machineand the nearby environment dust & pollution free.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Minimum Order Quantity 1 Unit Price Range 2500000.00 - 3000000.00 INR/Number Product Specifications: Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Product Type Other Power Source Electricity Power 420 Volt (v) Usage/Applications Casting, Forging, Sheet metal etc Color Dark Blue Technology Other Operating Type Automatic Surface Treatment Painted Pressure 6-7 Bar Product Description: The Tunnel type/ roller conveyor shot blasting machine is best suitable for the shot blasting of I/H-Beam /Structural Steel Components etc. It consists of inlet and outlet side Roller conveyors as material handling systems. The components to be blasted are placed on inlet side of the roller conveyor, from where it travels forward and enters into the inlet tunnel. After passing through the inlet tunnel components enters into the blast zone which consists of 4 nos. of Blast Wheels. All these Blast wheel units are strategically placed around the Blast cabinet. The arrangement of the blast wheel ensures optimum blast cleaning and maximum utilization of the abrasive energy. Blast wheels fires the abrasive at high velocity onthe forward moving components & blast cleans them thoroughly. Blasted material moves forward and enters into the outlet tunnel. The spent abrasive from blasting operation after passing through the perforated floor plates will get collected in to the cabinet's bottom storage hopper. From where it is transferred to the bucket elevator, which elevate the abrasive vertically and discharges the same into a media separation unit where dust and fine abrasives are cleaned ensuring that only clean abrasive will re-circulate to the blast wheel units for effective and better cleaning. A Dust collection system is provided with the machine which will continuously remove the dust and fine particles, thus keeping the inside of the machine and the nearby environment dust & pollution free.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Minimum Order Quantity 1 Unit Price Range 2000000.00 - 2500000.00 INR/Number Product Specifications: Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Pressure 6-7 Bar Weight (kg) 3.5-4 Metric Ton Color Dark Blue Product Type Other Power 420 Volt (v) Usage/Applications Casting, Forging, Sheet metal etc Operating Type Automatic Surface Treatment Painted Technology Other Power Source Electricity Product Description It consists of inlet and outlet side Roller conveyors as material handling systems. The components to be blasted are placed on inlet side of the roller conveyor, from where it travels forward and enters into the inlet tunnel. After passing through the inlet tunnel components enters into the blast zone which consists of 4 no's of Blast Wheels. All these Blast wheel units are strategically placed around the Blast cabinet. The arrangement of the blast wheel ensures optimum blast cleaning and maximum utilization of the abrasive energy. Blast wheels fires the abrasive at high velocity on the forward moving components & blast cleans them thoroughly. Blasted material moves forward and enters into the outlet tunnel. The spent abrasive from blasting operation after passing through the perforated floor plates will get collected in to the cabinet's bottom storage hopper. From where it is transferred to the bucket elevator, which elevate the abrasive vertically and discharges the same into a media separation unit where dust and fine abrasives are cleaned ensuring that only clean abrasive will re-circulate to the blast wheel units for effective and better cleaning. A Dust collection system is provided with the machine which will continuously remove the dust and fine particles, thus keeping the inside of the machine and the near by environment dust & pollution free.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Painted Supply Ability : 7-10 Unit Per Month Price And Quantity: Minimum Order Quantity 1 Unit Price Range 1200000.00 - 1500000.00 INR/Unit Product Specifications: Power Source Electricity Surface Treatment Painted Product Type Other Technology Other Power 420 Volt (v) Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Pressure 6-7 Bar Color Dark Blue Usage/Applications Casting, Forging, Sheet Metal Operating Type Automatic Product Description: The diabola conveyor shotblasting machine is best suitable for the shot blasting of round BARS. Itconsists of inlet and outlet side diabola conveyors as material handling systems. The components to be blasted are placed on inlet side of the rollerconveyor, from where it travels forward and enters into the inlet tunnel. Afterpassing through the inlet tunnel components enters into the blast zone which consists of 1 no. of Blast Wheel. This Blast wheel unit is strategicallyplaced around the Blast cabinet. The arrangement of the blast wheel ensures optimum blast cleaning and maximum utilization of the abrasive energy. Blast wheels fires the abrasive at high velocity onthe forward moving & rotating components & blast cleans them thoroughly. Blasted material moves forward and enters into the outlet tunnel. The spent abrasive from blasting operation after passing through the perforated floor plates will get collected into thecabinet's bottom storage hopper. From where it is transferred to the buck etelevator, which elevate the abrasive vertically and discharges the same into a media separation unit where dust and fine abrasives are cleaned ensuring that onlyclean abrasive will re-circulate to the blast wheel units for effective and better cleaning. A Dust collection system is provided with the machine whichwill continuously remove the dust and fine particles, thus keeping the inside of the machine and the nearby environment dust & pollution free.
Product Details: Product Type Other Technology Other Power Source Electricity Operating Type Automatic Power 420 Volt (v) Pressure 6-7 Bar Surface Treatment Other Supply Ability : 7-10 Number Per Month Price And Quantity: Price Range 600000.00 - 800000.00 INR/Number Minimum Order Quantity 1 Number Product Specifications: Product Type Other Pressure 6-7 Bar Technology Other Usage/Applications Casting, Forging, Sheet Metal Warranty: All our machines are warranted for 12 months from the date of commissioning or 15 months from the date of dispatch whichever is earlier against all manufacturing defects. However this warranty not covers parts consumed at normal wear and tear during operation like rubber goods & parts in continuous contact of abrasive media and also any damages due to misuse or improper handling of the machine at customer premises. The warranty will lapse if customer uses spurious spare parts purchased from any other buyer on the machine and fail to operate and maintain the machine in accordance with the instructions. Weight (kg) 4.5-6.5 Metric Ton Operating Type Automatic Power 420 Volt (v) Power Source Electricity Surface Treatment Other Color Dark Blue Product Description Hanger type shot blast machines designed and built as fully integrated blast cleaning systems to handle large/small or more fragile castings than barrel/table type machines. They provide a cost-effective solution for batch cleaning. Hanger typeMachine consists of horizontal door with a rotating hanger type work/job handling system. This hanger is directly mounted on the door of the machine and itrotates on its own axis, drive unit of this hanger is provided outside the door. This hanger swings out as the door is opened, making the full area easily approachable for loading and unloading of the components. For loading the components, door of the machine is opened manually & components to be blasted are hanged one by one on to the door hanger and the door of the machineis closed. Specification: Number of Doors Single Door Brand Adl Blastek Power Required 14.5 HP Capacity 10-15 ton/day Voltage (V) 415 V Driven Type Belt Driven Wheel No. Of Blast Wheels 2 Wheel Size (inch) 12.5'' X 2.5'' Model Number BT-SPH-1 Load Carrying Capacity Of Hanger (kg) 300 Kg Automatic Grade Automatic Blast Wheel Power 5 HP No. of Door with Hanger Hook 1 Diameter and Height Of Hanger Turning Meter 600 x 700 mm
