Lifting Electromagnet

Yx1 series permanent lifting magnetic nd-fe-b magnetic material by a special magnetic system, it is through shaking the handle to control magnetic switch. With no excitation power, small size, light weight, suction holding force, easy to operate, safe to use, magnetic timeless features. Widely used in factories, docks, warehouses and transportation sector lifting and transportation steel, steel ingot until the guide magnetic objects.



Depends

This series owing to light self-weight, reasonable structure(just contact with two points of the bar)is suitable for coiled bar, and has replaced former series mw22-¡õ54, which are not recommend by us now.However we still list main data for these two series for your reference, its magnetic pole is suitable for coiled bar which is of different diamneter.The length of coiled bar is important is choosing the right electromagnet.It can be put into operation along length or width direction of electromagnet and multiple units can be used together or separately as well.



Depends

Electromagnetic Lifter Application
Electromagnetic Lifter is suitable for transferring cast ingots, steel balls and kinds of steel scraps.

Electromagnetic Lifter Features
1. It adopts a special magnetic circuit design which has large air space and magnetism density. It is made of aluminum wire or copper and the coil protection plate is made of the rolled high Mn steel plate that has good performance of wear-resistance and heat-proof. It also has the characteristics of light weight, low power consumption, high lifting capacity and long serving life.

2. This series has fine insulation structure. The insulation treatments adopt the vacuum drying & glue filling, which has improved the electrical and mechanical performance of the coils .The insulation grade can reach class special C.

3. It generally adopts the control mode of constant voltage. It can further improve the lifting capacity if changing to adopt the control mode of over excitation.

4. With simple structure reliability, it is suitable for working with all kinds of lifting equipment.


Electromagnetic Lifter Classification
MW84 series is specially designd for lifting and transporting medium-thick steel plate .The whole operation is safe, exact and quick , when transport some long plates they easily go disto rtion, so we advice combination of multiple units to be used. For some plate which thickness is around the range of 6mm-32mm, space between 2 magnets should leave an extra 2.5-3.5m, the length at each end is that of one half of space.According to different lifting pieces, the series is divided into type 350 and type 400 and type 500 and type 650.Type 350 is suitable for medium-thick plate factory, ship building factory, machinery manufacturing factory, it is controlled by adjustable magnetic field, and can lift one or certain pieces of plates. Type 400 is suitable for lifting as many as possible pieces at a time ; We can also produce the product less than 700°c ( high temperature type) for you.

MW5 series magnet chuck is an electromagnetic principle, by internal coils generate magnetic force, through magnetic panel, the contact surface of the workpiece panel tightly sucked through the coil power, the magnetic force disappears achieve demagnetization, remove the piece of principle the production of a machine tool accessories.


Packaging & Shipping
1. Delivery time
Within 10 business day after the receipt of deposit.
2. Packaging
Wood case for electric parts, accessories;large sections will be loaded onto bulk cargo ship after packing.
3. Payment terms
FOB, CFR and CIF are common trade terms. We can accept payment terms: TT, L/C, west unit, DUP, DUA and other.
4. Installation
the installation team can be sent to local site to install for customer.
5.Warranty
We'll be responsible for maintenance if our product itself has quality problem during one year after receiving.

z

1.Lifting Electromagnet Series LM5 for Lifting and Transporting Steel Scraps. Suitable for transferring cast ingots, steel balls and various kinds of steel scraps.
2.Rugged ¿Call-welded construction with all moisture proof.
3.Optimized design by computer with reasonable structure, higher suction weight ratio and low energy consumption.
4.Energizing coils processed by special technology with improved electrical property and mechanical property. Heat-resistant grade of insulating materials reach grade C with long service life.
5.Various structures and technical data are available based on the attached items under different conditions to satisfy the wide demands from the clients.
6.High temperature type electromagnet adopting unique method of heat-protection. Temperature limit of the attached items is increased from 600íµ to 700íµ, which expands the application range of lift electromagnet.
7.Easy and convenient installation, operation and maintenance.
8.We can manufacture all magnetic devices according to customers' requirement.

Technical features of swdct ems
1.A new algorithm has been developed by "swdct" and gl electromagnetic field software co., names agild em stirring algorithm which uses new strip magnetic field differential integral equation.
2.This software can design electromagnetic parameters optimized. Ems shall be with high magnetic induction and stirring force. So stirring effect shall be great.
3.Stirring force can be calculated by this software according different freq and current. So the best freq and current can be provided for user.
4.Optimized design shall be done for l/d. Iron core length shall be increased properly. So stirring effect shall be improved.
5.Our term has also other software for designing f-ems to calculate best position of f-ems
6.Swdct uses low voltage and large current, which can avoid damage of peak voltage to insulation. It shall make reduce current leakage and prolong ems life.
7.Freq arrange shall be widened to choose the best freq.
8.Put ems lower properly to make magnetic field around meniscus as little as possible to ensure strong magnetic field.



Depends

Electromagnet

Kemeida Magnet currently operates in the largest of production lines to the smallest job shops and provides the same advantages of safety, high performance, and low operating cost for each user. For sheet, plate, block, round or angle, Kemeida has a magnet for any application. Let Kemeida's engineers evaluate the feasibility of applying our principle to your magnet application.

How Electromagnet Works?
Here we take scrap steel for example. An electromagnet can be used for moving scrap steel from one place to another. In a scrapyard, a crane has a large iron disc that is not a permanent magnet. The crane operator lowers the electromagnet into a pile of scrap steel and then switches on the electricity. This causes the steel disc to become a powerful magnet. Scrap steel is attracted to the disc. When the operator switches off the electricity, the scrap steel falls off the disc. In this way, large amounts of scrap steel can be moved easily from one place to another.

Rectifier Controllers
Electromagnets require direct current power for operation. Whether used in manual or automated handling of ferrous parts, they must release the work as readily as they attract and hold. Release is a function of the rectifier and not the magnet. These rectifiers incorporate a provision for reverse current that ensures positive release of even those alloy steels which are magnetically retentive. Variable power and remote control are available. Rectifiers and rectifier-controllers are designed to provide reliable D.C. power for industrial electromagnets.

About Inquiry
To help you get the best magnet for your application, we should have the following information:
1. What are the materials you want to attract?
2. What kind of steel and iron? For example: steel scraps, steel billet, ingot, plate, bar or ball.
3. What¡¯s the lifting capacity you expect?
4. What kind of working site does the magnet work?
5. Do you want the Cable Reel? If yes, tell me hoist height of the crane.
6. Do you want the electric controller?