300Ah Lfp Type 3.2V Lithium Iron Single Cell

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

Type volts (ah)capacity 20 hr no plate/cell 12 n24-4 12 26 9 Ns40/l 12 32 9 Ns40 z/l 12 36 11 N40/l 12 40 9 Ns60/l 12 45 11 Ns60 s/sl 12 45 11 N50/l 12 50 9 N50 z/l 12 60 11 Ns70/l 12 65 13 N70/l 12 70 13 N70z/zl 12 75 15 Nx120-7 12 85 15 N100 12 100 17 55d23 12 60 11 N120 12 120 21 N150 12 150 25 N200 12 200 31 N200 12 200 33

Type - NR : 55423 Replacement Type - NR : 55218, 55427, 55531 Hold down : B3 Assembly layout : 0 Capacity (Ah) 20 Hrs rate : 54 Cold cranking : 300 Dimension L 249 W 175 H 175.

Type : 40 L Volt : 12 Number of plate/cell : 9 Capacity (Ah) 20 Hrs rate : 32 Cold cranking : 250 Dimension L 195 W 125 H 198 T.H 220.

Type - NR : 54533 Replacement Type - NR : 54519 Hold down : B4 Assembly layout : 0 Capacity (Ah) 20 Hrs rate : 45 Cold cranking : 190 Dimension L 249 W 175 H 175.

Type/size of seperator: W x T 122 x 1.4 130 x 1.7 138 x 1.1 140 x 1.8 139 x 1.8.

Supplier: Lithium ion battery, lithium polymer battery, lifepo4 battery

Supplier: Battery, button cell, alkaline battery, lithium battery, high voltage battery