Metal Machining Part-1

Pularin: Foot ball shaped 60 atoms of carbon at edges is layed in pularin.Pularin atoms are arranged in ball. Each atom is called Bucky balls and tubes are called Bucky tubes or Nano tubes.Each nano tube is 1 to 7 nm diameter i.e 1nm=50000 part of a hair sting. where? 1)mangampet ,cuddapah dist.Ap,India.app 800 ppm(parts prer million)info given by stanford University. Cost: 150 times costlier than gold. 10 grams pularin $23000 to $45000 also info given by Bucky-USA website. Special uses if this becomes common: 1)Pularin coting on aeroplanes withstands from thunders ,rains ,Flashes etc. 2)Bullet proof ackets 3)curing cancer etc.

We are leadding manufactrer and exporter of Brass and Metal swival ball joint.

C: 0.54-0.8% Si: 0.18-0.40% Mn: 0.60-1.05% S: 0.04% Max P: 0.035% Max Used rails R50-R65 Under 200-202 International Standard ISRI Code 27-29 R50 R65 Harmonization System (HS) Code : 730210

1,Hight prurity (99.99% min) Metal Antimony (Sb) 2,4N>99.99%, 5N>99.999%, 6N>99.9999%, 7N>99.99999% 3,Lumps/Ingot/Granule/Bar 4,Color: Gray 5,Atomic weight: 121.760 6,Electronegativity: 2.05 7,CAS No.: 7440-36-0 8,Density: 6.697 g/cm3 (25â??) 9,Melting Point: 630.63 â?? 10,Boiling Point: 1587 â?? 11,Mainly used for the preparation of â?¢ - V compound semiconductor InSb, Bi2Sb, GaSb, high purity alloys, electronic refrigeration element materials and germanium, silicon single crystal dopants.

Raw melting material - aluminum scraps, cans, engine waste etc. Output capacity - 5-30 tons/h, customized Automation - Full automatic/ half automatic (based on output requirement and investment budget Ingot type - ADC12 (7.5kg/ 10kg / customized) 1. After cleaning the oil and grease of waste aluminum, manually put it into the furnace with a forklift; 2. Ignition for melting furnace .Heat up to 680C, and input appropriate proportion of alloy elements. Heat up to 800C, melt and stir evenly, then fetch samples to the spectrometer for testing. Every lot of production need to do testing . 3. Put A tool that attracts iron into the furnace by forklift, to suck away the iron in the aluminum water. 4. Put the slag agent into Alu liquid to remove the slag. After slag removed , put the slags into Aluminum ash separation machine , and let the aluminum water and ash separate. The proportion of slag agent and aluminum liquid is 1:500 5.Open the drain valve and the aluminum water flows automatically to the ingot production line After the ingot casting is completed, the ingot stacking robot will stack the ingots, which means the production is completed.

We engage in metal materials, metal products, steel products, i.e. ferrosilicon, titanium iron, silicon ferrozirconium, ferrovanadium, ferrowolfranium, mg-ferrosilicon-rare-earth alloy, ferromolybdenum, ferrochromium products, ferromanganese products; non-ferrous metal products, i.e. stibium ingot, silicon-calcium, silicon manganese, zinc-alum alloy, zinc ingot, lead ingot, chrome powder, magnesium ingot, aluminium ingot/ coil/ can/ scrap, copper ingot/wire/ sheet/ scrap, Plastic and Polymer Scrap, Plastic Raw Material Granules, Rubber Scrap, Paper Scrap, etc. Chemical Composition: C:0.06 - 0.082% Mn:0.75 - 1.05% SI:0.13 - 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15% HMS 1 / 2 STEEL METAL SCRAP FOR SELL: Iron Scrap HMS1 & 2 C:0.06 - 0.082% Mn:0.75 - 1.05% SI:0.13 - 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15% HMS 1 / 2 STEEL METAL SCRAP FOR SELL: Iron Scrap HMS1 & 2 C:0.06 - 0.082% Mn:0.75 - 1.05% SI:0.13 - 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15%