Split Core Current Sensors

Main Features 1.Small size, low cost 2.High secondary turns 3.Secure locking hinge Model No: MEWOI-CT10,16,24,36,50 Name: MEWOI-CT10,16,24,36,50 Split Core Current Sensor/Transformer Rated Current:5A to 600A loads Rated output:0.333Vac Current Ratio:3000:1 Insulation Voltage:600Vac Maximum Primary Voltage:5000Vac(Insulated Conductor) Operating Temperature:-15 to 60 Frequency Range:50-400Hz Leads:4Foot (105cm), UL 1015, Twisted Pair,0.34mm2(22AWG) Output and leads:can be customized Application 1.Sub-Metering Accurate Measurement 2.Data Loggers to analyze Building & Machinery Performance 3.Digital Fault Recorders 4.Smart Grid Application Features Load Center 5.Three Phase Balance Control 6.In-Factory Display In-Home Display 7.Inverters for Solar & Wind Turbine Systems 8.Power Measurement Device For PLC

Main FeatureS: small DC leakage current measurement Model No.: MEWOI-DRSL(DC)2000mA Name: MEWOI-DRSL(DC)-2000mA Leakage current sensor Diameter: Ï?33mm Rated input Current (IPN)50 100 500 1000 2000 mA(DC) Primary Current Measure range(IP) :0100 0150 0600 01200 02200mA Rated output voltage of secondary side DC ±5V 4-20mA 0-20m Power Supply Voltage ï¼?VCCï¼? DC ±12V15V Current consumption

Supplier: Current transformer, split core current transformer, current sensor
Buyer: Current transformer, split core current transformer, current sensor

Min Fetures: DC lekge current mesurement Model No.::MEWOI-DRST-200m(DC) Nme: MEWOI-DRST-200m(DC) Split Core Lekge current sensor Dimeter:Ï?19mm Rted input Current (IPN)102050100200m(DC) Primry Current Mesure rnge(IP)0-±200-±500-±1000-±2000-±300m Rted output voltge of secondry sideDC ±5V, 4-20m, 0-20m (±1%)V Power Supply Voltge (VCC)DC ±12V-±15V (±5%)V Current consumption

The FQ-RCTA02 rogowski coil flexible current sensor is designed for easy installed in tight spaces and without the need for dismantling the primary busbar or cables. It includes a flexible Rogowski coil probe and electronic modules. The signal from the coil probe can be amplified by the electronic amplifier modules through the integration processing. The output signal can be directly used in oscilloscope, digital multimeter or data logger recording instrument. good linearity, easy to use, measuring large current, 6000A/3V, 600A/3V, 60A/3V or 3000A/3V, 300A/3V, 30A/3V, lower phase shift. In particular, it can be installed in tight spaces, around cable bundles, around wide or large bus bars, or even wrapped around irregular shapes. Models range from 1 to 100,000Arms with an accuracy of 1% of reading. Rated EN 61010, 600V CAT IV, 1000V CAT III. This feature facilitates positioning the sensor around the conductor, enhances user safety, and alleviates the drooping effect associated with other flexible sensors. FEATURES

The HQ15 100a current probe sensor is designed for easy installed in tight spaces and without the need for dismantling the primary busbar or cables. The sensing head uses sliding push-fit clamp structure, safety isolation to avoid the user to contact with charged objects directly. It complies with CE standards and meets 300V CAT III safety class. This model HQ15 current sensor is a high accuracy mini current probe for measurements up to 130A AC. This current probe uses a special magnetic core to provide higher accuracy and lower phase shift. The HQ15 Series is an excellent probe sensor to be used in power and low level current measurement applications. FEATURES UL, CE CNAS mark Excellent linearity High content permalloy core Holding wire diameter: 15mm Frequency 10Hz-5kHz Bandwidth High time harmonics measurement Easy &quick installation in tight spaces; Measurement range of 1mA to 130A AC; Low phase shift for power measurement;   EN 61010-2-032 , 300V CAT III Standard Improved ergonomic design & easy operation; High precision 0.1% for current measurement Flexible and light weights, exquisite appearance;

Type : RTCS100B,RTCS200B,RTCS300B,RTCS400B,RTCS500B,RTCS600B, IPN Primary nominal input current : 100, 200, 300, 400, 500, 600 A IP Measuring range of primary current : 0~300, 0~600, 0~900, 0~900, 0~900, 0~900 A VOUT Nominal output voltage : 41%V VC Supply voltage : 15(5%) V IC Current consumption : VC=15V

Hall components have many advantages, they are strong construction, small volume, light weight, long service life , easy installation, wide bandwidth ( can reach 1 MHZ);vibration resistance, Not afraid of pollution or corrosion of dust ,oil, greasy dirt, moisture , salt mist and so on. • Hall linear elements are excellent accuracy, good linearity. Hall switch elements are no contactless, no in-gage, clear output waveforms, no instant jitter, high-precision positional repeatability. In recent years, with the development of China aerospace industry .Our hall-effect product is widely used in new rocket ,new generation communication satellite, new navigation satellite, new recoverable satellites, chang-e satellites, Shenzhou spacecraft and so on . Its related products is also can widely used in automotive matching, environmental protection, medical equipments, instrument, power protection, office automation and many other civil fields. It is wildly used in frequency driver, contravariant devices, UPS, contravariant welding machine, converting station, electrolyze & electroplating, CNC machine, PC monitoring, grid monitoring, insulated current & voltage testing, Etc. Working Principle 1.Direct measurement principle 2.Magnetic compensation principle Packed in box ,can be customized

FEATURES Suitable for 5A, 10A cable online measurement. Holding wire diameter: 8mm Dimension: 42.6mm 122.5mm 23mm Load capacity: 4 Installation: clamp type Output mode: lead output PARAMETERS Electrical parameters Ratio 1000: 1 or 2000:1 (customized) Accuracy class 0.2%, 0.5% Primary current 0 - 10A AC Secondary current 0 - 10mA AC (customized) Max. Cont. Input current 12 A Load capacity 4 Over voltage category CAT III 600V Output signal (AC current) From 0 to 10mA AC at nominal input current Output signal (AC voltage) From 0 to 1V AC at nominal input current Frequency range 40Hz-2000Hz Dielectric strength 3KV 50Hz/60Hz at 1minute Temperature range -20C to +55C Output 2.5 meter cable with D01 connector Max. voltage not insulated conductors 600 V Standard EN 61010-1, EN 61010-2-032, IEC60044-1 Installation Clamp type Output mode Lead output(2.5m) Mechanical parameters Dimensions (L x W x H) (mm) 42.6 122.5 23 Weight (g) 225 Holding wire diameter (mm) 8 Max. jaw opening (mm) 8 Color Gray Material PC+ABS+Polycarbonate, UL94 V0