DPOX180H is a cost-effective handheld dual-channel digital phosphor oscilloscope launched by FNIRSI with a two-in-one oscilloscope and signal generator. The oscilloscope has a real-time sampling rate of 500MSPS and an analog bandwidth of 180MHz. In terms of display, a high-contrast 2.8-inch IPS full-vision LCD screen and digital fluorescent technology are used. The waveform display effect is good, and the color ways are grayscale and color temperature. With a waveform refresh rate of up to 50000wfm/s, it is easier to display abnormal signals with low probability. The time base system includes a ZOOM time base for easy analysis of digital protocol signals. With a vertical sensitivity as low as 5mV, it can better measure small signals of 5mVPP. Ultra-high signal-to-noise ratio, fully sealed shielding measures, stable circuit feedback design, clean and clear waveform. The original adjustable automatic bandwidth limit and adaptive adjustable trigger suppression are suitable for analyzing and measuring signals with relatively large noise. 20M hardware bandwidth limit, can filter out noise above 20MHz. The trigger adopts digital trigger technology with high precision. It has three trigger modes: automatic/single/normal. It has a strong ability to capture periodic signals, burst signals and protocol signals. The DDS signal generator has 14 kinds of function signal waveforms and a free-customized chopping waveform. The frequency of the sine wave can reach up to 20MHz, and the other waveforms can reach up to 10MHz. The original chopping output function can store up to 500 customized signals. It has three time base modes of YT, XY and rolling. Manual cursor measurement is suitable for measurements with large noise signals. Efficient one-button automatic adjustment, adaptive 25%, 50%, 75% electric level trigger, it only takes 2 seconds to measure 1VPP/1KHz. Save waveforms and screenshots with one key, up to 250 sets of waveform data or 90 pictures can be stored, and 500 intercepted wave data can be stored at the same time. The data browser can browse and view the currently saved waveform data and pictures, and the waveform data supports operations such as zooming and moving. High voltage anti-burning protection, all gears can withstand high voltage up to 400V. USB data export, you can connect to a computer to copy picture files, and you can also copy system files to the oscilloscope for system upgrades. 5V2A fast charging, and 1 hour can charge to 80%.
FNIRSI-1C15 Professional Digital Oscilloscope 500MS/s Sampling Rate 110MHz Analog Bandwidth Support Waveform Storage FNIRSI-1C15 is a fully functional, practical and cost-effective handheld oscilloscope newly launched by FNIRSI. The real-time sampling rate is 500M, and the analog bandwidth is 110MHz. In addition to all the functions of a conventional handheld oscilloscope, we also added a one-key quick auto function on this basis, so you can easily grasp the waveform like a desktop computer. We have added 1k Hz self-test square wave for FNIRSI-1C15, and the storage depth has been upgraded to 12kpts. With reference to the waveform, you can pause at any time to save the previous frame waveform to the screen, and you can compare it with the currently refreshed waveform. Afterglow and scroll modes make it easier to detect and record waveforms. Built-in 3000mAH rechargeable battery, it can work continuously for more than 10 hours after fully charged. The body is equipped with a high-quality silicone sleeve, which is non-slip and anti-drop. The joystick replaces the original arrow keys, making the operation simpler and more effective. Package: 1 * FNIRSI 1C15 oscilloscope 1 * P6100 High Voltage Probe 1 * Allgator Clip Probe 1 * Micro USB charging cable 1 * English User Manual 1 * Cloth bag
Digital Thermo-Hygrometer
FNIRSI-1C15 is a fully functional, practical and cost-effective handheld oscilloscope newly launched by FNIRSI. The real-time sampling rate is 500M, and the analog bandwidth is 110MHz. In addition to all the functions of a conventional handheld oscilloscope, we also added a one-key quick auto function on this basis, so you can easily grasp the waveform like a desktop computer. We have added 1k Hz self-test square wave for FNIRSI-1C15, and the storage depth has been upgraded to 12kpts. With reference to the waveform, you can pause at any time to save the previous frame waveform to the screen, and you can compare it with the currently refreshed waveform. Afterglow and scroll modes make it easier to detect and record waveforms. Built-in 3000mAH rechargeable battery, it can work continuously for more than 10 hours after fully charged. The body is equipped with a high-quality silicone sleeve, which is non-slip and anti-drop. The joystick replaces the original arrow keys, making the operation simpler and more effective. Model : FNIRSI-1C15 Number of channels : 1 Screen size : 2.4 inches Screen Resolution : 320*240 Analog bandwidth : 110M Sampling Rate : 500M 1k Hz self-checking square wave Stand by Rise Time :
FNIRSI-1013D Digital tablet oscilloscope dual channel 100M bandwidth 1GS sampling rate mini tablet digital oscilloscope FNIRSI 1013D is a full-featured, highly practical, cost-effective dual-channel flat-panel oscilloscope for the maintenance and R & D industry. note:After the production of the product, we will carry out multiple measurements to ensure the quality of the product. If you encounter any problems in the use, please contact us, and we will contact the technical personnel to answer for you at the first time. Features: Intelligent anti-burn,1X can withstand up to 400V withstand voltage. 100MHz analog bandwidth @ 1GSa/s sampling rate (1X=5MHz,10X=100MHz). Fully fit 7 inch 800 * 480 resolution color TFT LCD display with bright colors and high contrast. Capacitive touching screen, the same as the touching mode of modern mobile tablet, is not a resistive touching screen with ancient nail operation. High measurement voltage range, 1X can measure 0~40V, 10X can measure 0~400V,100X can measure 0~4000V. Up to 12 parameters measurement: VPP,VP,Vmax,Vmin,Vavg,Vrms,Frequent,Duty+,Duty-,Time+,Time-,Period. Cursor measurement function, it is convenient to manually measure the period and frequency and voltage. Complete triggering function (single, normal, automatic). At any time, the waveform display (pause function) is frozen. Equipped with high efficiency One-button AUTO. One-button waveform storage and screenshot. Built-in 1GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data. Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc. Equipped with a USB interface, which can be connected to a computer to share its screenshots with the computer, which is convenient for secondary analysis. Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals. FFT display function, can analyze the spectral characteristics of the signal. Built in 6000mAh rechargeable lithium battery,fully charged for 4 hours of continuous use at the highest screen brightness. Memory compression technology, waveform refresh screen does not flicker. Screen brightness adjustment. Background grid brightness adjustment. Ultra thin, easy to carry.
FNIRSI-5012H 2.4-inch Screen Digital Oscilloscope 500MS/s Sampling Rate 100MHz Analog Bandwidth Support Waveform Storage The FNIRSI-5012H is a versatile, highly practical, cost-effective handheld oscilloscope for the maintenance industry and the R&D industry with FNIRSI's real-time sampling rate of up to 500MS/s and 100MHz analog bandwidth. With full trigger function (single, normal, automatic), it can be used freely for both periodic analog signals and non-periodic digital signals. The built-in high voltage protection module can withstand up to 400V continuous voltage and 600V peak voltage. Don't worry about the oscilloscope burnout caused by the high voltage not being probed to the 10X position. Large time base scan mode that monitors slow level changes. Equipped with high-efficiency one-button AUTO, the measured waveform can be displayed without complicated adjustment. Display high-definition LCD screen with 2.4-inch 320*240 resolution. Extremely convenient and fast waveform storage function, built-in 64M storage space, can store up to 2000 waveform pictures, the storage process is simple and fast, save the current waveform anytime and anywhere, just one touch, no cumbersome tips and choices, quietly It is very convenient to save the current waveform. Key features: 1:Intelligent anti-burn,1X Can withstand up to 600V withstand voltage 2:Afterglow display technology 3:2.4 inch color display screen 4:100MHz analog bandwidth @ 500MS/s sampling rate(1X = 5MHz,10X = 100MHz) 5:One-button waveform storage 6:Built-in 64M storage space, the maximum storage of 2000 waveform pictures 7:Powerful waveform file manager, support thumbnail browsing, viewing, details view, flip, delete and other functions 8:High measurement voltage range, 1X can measure 0 ~ 80 V, 10X can measure 0 ~ 800V 9:Up to 12 parameters measurement:VPP,VP,Vmax,Vmin,Vavg,Vrms,Frequent,Duty+,Duty-,Time+,Time-,Time 10:At any time, the waveform display (pause function) is frozen 11:Equipped with high efficiency One-button AUTO 12:Complete triggering function (single, normal, automatic) 13:Built in 3000mAh rechargeable lithium battery,Fully charged for 8 hours of continuous use Package includes: 1 x FNIRSI-5012H oscilloscope host 1 x Matching 100MHz probe(1X and 10X) 1 x Micro USB data line 1 x User manual (English) 1 x High quality package
Features: Built in DDS signal generator, support 12 kinds of function signal. Capture output signal function, which can store up to 1000 capture signals. Targeted high intelligent decoding algorithm, the encoderlifeis infinite, and intelligent anti-burn function, 1X Can withstand up to 400V withstand voltage. With 100MHz * 2 ana-log bandwidth and @ 1GSa/s sampling rateï¼?1X = 5MHz, 10X = 100MHz). Fully fit 7 inch 800 * 480 resolution color TFT LCD display with bright colors and high contrast. High measurement voltage range: 1X can measure 0~40 V, 10X can measure 0~400V. Up to 12 parameters measurementï¼?VPPï¼?VPï¼?Vmaxï¼?Vminï¼?Vavgï¼?Vrmsï¼?Frequentï¼?Duty+ï¼?Duty-ï¼?Time+ï¼?Time-ï¼?Period. Cursor measurement function: it is convenient to manually measure the period and frequency and voltage. Complete triggering function (single, normal, automatic), and at any time, the waveform display (pause function) is frozen. Equipped with high efficiency One-button AUTO, and one-button waveform storage and screenshot function. Built-in 1GB storage space, can store up to 1000 screenshots + 1000 sets of waveform data. Powerful waveform picture manager supports thumbnail browsing, viewing, detailed viewing, page turning, deletion and waveform zooming in, zooming out, moving, etc. Equipped with a USB interface, which can be connected to a com-puter to share its screenshots with the com-puter, which is convenient for secondary analysis. Lissajous figures graphic display function can be used to determine the amplitude, frequency, and phase contrast of two groups of signals. FFT display function, can analyze the spectral characteristics of the signal, memory compression technology, waveform refresh screen does not flicker. With the screen brightness adjustment function and background gr-id brightness adjustment function, also easy to carry.
FNIRSI DSO-TC3 combines a digital oscilloscope, electronic component tester, signal generator, continuity test, voltage test, temperature and humidity measurement, infrared decoding and other functions are skillfully integrated. It is equipped with a 2.4-inch color TFT display, built-in rechargeable lithium battery, brings users stronger and more practical functions with good portability. FNIRSI DSO-TC3 is an upgraded version of DSO-TC2. On the basis of DSO-TC2, it has upgraded capacitance ESR detection, function signal generator output, oscilloscope bandwidth and sampling rate improvement, input voltage and diode detection range increase and so on. The improvement in performance and function of DSO-TC3 makes the device more stable and accurate in the detection process.
FNIRSI-1014D Digital Oscilloscope 2 In 1 Dual Channel Input Signal Generator 100MHz 2 Ana-log Bandwidth 1GSa/s Sampling Rate. FNIRSI 1014D 100MHz Two Channels 1gsa/s Oscilloscope. Features: 1. Built in DDS signal generator, support 12 kinds of function signal. 2. Capture output signal function, which can store up to 1000 capture signals. 3. Targeted high intelligent decoding algorithm, the encoderlifeis infinite, and intelligent anti-burn function, 1X Can withstand up to 400V withstand voltage. 4. With 100MHz 2 ana-log bandwidth and 1GSa/s sampling rate 1X 5MHz, 10X 100MHz). 5. Fully fit 7 inch 800 480 resolution color TFT LCD display with bright colors and high contrast. 6. High measurement voltage range: 1X can measure 0 40 V, 10X can measure 0 400V. 7. Up to 12 parameters measurement VPP VP Vmax Vmin
Specifications: Size: 5.1 x 2.8 x 2.0 in. / 13.1 x 7.0 x 5.2 cm Weight: 11.5 oz. / 328 g Temperature: -4 to 122F / -20 to 50C Readily enables to communicate with Motorola MOTOTRBO Description: The Honeywell Max XT II is a rugged, handheld mobile computer that is designed for use in demanding environments such as warehouses and manufacturing facilities. It features a high-performance processor and a large, easy-to-read display, making it ideal for tasks such as barcode scanning and data collection. The device is built to withstand drops, bumps and exposure to extreme temperatures and is sealed against water and dust. With a long-lasting battery and the ability to run multiple applications simultaneously, the Max XT II is a reliable and efficient solution for mobile data collection and communication in industrial environments. Benefits: Monitors H2S, CO, O2 and combustibles. One-button operation with robust, motorized pump. Compatible with MicroDock II
