Fully automated operations with datalogging, remote access and control
Multi-purpose application utilizing either outside-in or inside-out.
Independent side by side comparison possible.
Flow Rate 28800 40000 gpd
20 29 gpm
Weight Shipping 2000 pound
Operating 2400 pound
Dimensions 5 ft W x 9 1/4 ft L x 8 1/2 ft H
Membrane Modules 1. NORIT X-FLOW 23E1FL295H
2. HYDRAcap 60
Or any other pressurized manufacturer.
Frame material Carbon Steel
Power 230V, 3PH, 60 Hz, 40 Amps, NEMA 12
Clarifier type MEGACELL HORIZONTAL - MCH Clarifier size MCH 1 Pilot Plant Quantity 1 Design raw water flow 10 m³/h Pressurization 4 m³/h Material wetted parts Stainless steel 316Ti Material non-wetter parts Stainless steel 304 Air dissolving device type Air Dissolving Tube Size ADT 150 Quantity 1 Design flow, m3/h 4 m³/h
ALKAMEDI ionizers are using a single filtration system with 3 different filter types at the moment offers the most reliable and powerful water filter with state-of-art technology of ALKAMEDI. â? � � � � FB3 : 6 steps of Carbon Block Compound Filter. â?¡� � � � FU4 : 8 steps of Advanced Ultra Hollow Membrane Purification Filter. (Carbon Block Compound + UF Module Filter)� � � Expected in Q1, 2024 â?¢� � � � FN2 : 6 steps of NANO Silver Carbon Block Compound Filter. (Carbon Block Compound + NANO Filter)� � � Expected in Q1, 2024 The effectiveness of the filtration is determined by the valid filtration capacity verified by a testing institution, and this product is composed of a nano-carbon block composite with a valid water capacity of 3,600 liters for approximately 6 months. It is recommended to use for approximately 6 months and a voice guide will inform you when it is time to replace the filter. Alkamedi does have all kinds of certificates related to each continents and countries we export to such as CE, CB, UL, NRTL, TUV etc in order to meet all electrical regulations in each countries and regions.
We supply specialized  manufactured Shell amp Tube Heat Exchangers amp Pressure Vessels Delivering superior quality products in minimum delivery time MOC we can supply in copper brass carbon steels stainless steels like SS304 SS310 SS316L copper alloys such as cupro nickel Admiralty amp Aluminum Brass and many other materials We can supply Heat Exchangers amp Pressure Vessels up to 40 Tons The product range includes the proprietary plate fin tube heat exchanger oil coolers inter coolers after coolers marine heat exchangers oil cooling systems condensers chillers economizers super feed heat exchangers receivers and surge drums This products are extensively used in oil and gas refineries air separation plants chemical steel refineries pharmaceutical industries air conditioning amprefrigeration plants heat treatment shops marine engines amp gear boxes induction furnaces machine tools diesel engine generating sets compressors power plant installations transformers hydraulic power packs food processing vegetable oil refining amp sugar industry etc We are supplying this with certifications such as U R amp NB Stamp from ASME ISO 90012008 quality certificates from LRQA and certifications from DGQA IRS NSIC etc This are all manufactured in Nondestructive testing such as Visual Inspection Liquid penetrant testing Radiographic testing Tube to Tube sheet Weld radiography Ultrasonic testing for raw material and welds Helium leak testing Bubble Leak testing Magnetic particle testing
Water Based PSA for Tapes & Label stocks The pressure sensitive adhesives are characterized as having enhanced bonding characteristics including loop tack, peel strength, and shear strength making them particularly useful for the manufacture of dry-bonded laminates, tapes, labels, medical patches and devices, flexible packages, furnace ducts, exterior insulating finish system and the like. Grades are suitable for Pressure Sentitive coating applications in Label Stocks, Holograms and Tapes. Advantages : 1. It has very high tack and good Shear Strength with instant bond & non-migrating properties. 2. Low Odor, Non-Toxic, Non-Polluting.
Use only one plant to do hundreds of experiments is come true. We invented this plant with our rich experience in liquid concentration and separation in bioengineering, food and pharmaceutical, chemical and environmental industries. We installed three types membrane on it, there are spiral wound, plate (sheet) and tubular membrane. Various precision and materials are accomplished in one plant. Save large cost, and avoid failure and bad operation in big scale projects, help you find out the best solution. Application: Bioengineering: Clarification, concentration, separation of protein, polypeptide, amino acid etc. fermentation products; Separation, purification, and concentration of biochemical pharmaceutical intermediate; Desalination and refining of synthetic substances. Food and Pharmaceutical: Clarification and refining of sugar products; Clarification and concentration of gelatin, starch concentration and pyrogen removal; Separation, filtration and clarification of plant extracts; Separation, purification,sterilization, pyrogen removal of oral liquid and preparation; Removal and concentration of pigment; Filtration and refining of fruit and vegetable juice. Chemical and Environmental: Product desalination; Separation, purification and refining of high temperature solvent system. Treatment of oily waste water, ultrafine particle recycling in wastewater. Installed Membrane: Spiral Wound Membrane: Temperature: < deg. 45 C, Material: composite, polyamide, PS, PES, PVDF, Filtration Area:0.3m2 Precision (MWCO): RO, 150Da, 300Da, 1KDa, 2.5KDa, 3.5KDa, 5KDa, 8KDa, 10KDa, 20KDa, 75KDa. Tubular Membrane: Temperature: < deg. 100 C, Material: titania, alumina, zirconia, Filtration Area: 60 to 90 cm2 Precision (MWCO):50nm, 200nm, 500nm, 800nm, 1.2u. Plate (Sheet) Membrane: Temperature: < deg. 45 C, Material: PS, PES, PVDF, PTEE, Polyamide, Filtration Area: 0.02m2 Precision (MWCO): RO, 150Da, 300Da, 1KDa, 2.5KDa, 3.5KDa, 5KDa, 8KDa, 10KDa, 50KDa, 70KDa, 100KDa, 150KDa, 0.05u, 0.07u, 0.1u, 0.2u, 0.45u, 0.7u, 1.0u, 1.5u, 3u, 5u, 10u, 20u.
Erik compared more than 20 hydraulic pilot pressure control valve factories. No manufacturer can do the hydraulic pilot operated pressure control valves which can be used under high pressure above 450bar for more than one year. AAK hydraulic pilot operated pressure control valve passes the test at one time, and there is no abnormality after one year of use. Erik is from a German hydraulic equipment manufacturer. In the first half of last year, the company needed to purchase a special hydraulic pilot operated pressure control valve with a working pressure of more than 450 bar, a service life of more than one year and a durability of more than 2 million times. The boss realized that it was some difficult to purchase the hydraulic pilot operated pressure control valve this time, and asked Erik and his colleague to purchase at the same time. Whoever successfully purchased the hydraulic pilot operated pressure control valve first will be promoted and raised. Erik is full of energy and keeps looking for hydraulic pilot operated pressure control valve factories online and offline. He contacted more than 20 new suppliers, including AAK hydraulic valve. Most of the hydraulic pilot operated pressure control valve manufacturers replied that they need to be customized from the beginning of materials, and it takes 25 days to sample this special hydraulic pilot operated pressure control valve. Erik chose two factories to test the samples. A month later, Erik received the samples and asked the engineer to test them. The results failed, but the hydraulic pilot operated pressure control valve obtained by his colleague passed the first test, which made Erik very depressed. Fortunately, this is just in the test stage, the final effect depends on the test results of the hydraulic pilot operated pressure control valve one year later. Erik contacted AAK for the second time. He clearly informed that the samples of hydraulic pilot operated pressure control valves he selected in the first round failed. For the first time, he did not choose AAK because AAK needed 35 days. This time, he only asked AAK to make samples. Whether he can win or not, he can only count on AAK. Because the material selection and internal test of hydraulic pilot operated pressure control valves need time, Erik also understands the difficulties of making the samples. After 35 days, AAK sent 6 samples of hydraulic pilot operated pressure control valves. Last week, almost a year after the hydraulic pilot operated pressure control valve samples were sent, Erik sent an email to inform that AAK hydraulic pilot operated pressure control valve was the only sample that passed 2 million tests, and there was no abnormality after one year of use. Although his colleague's sample passed the early test, it could not withstand the high pressure above 450 bar for enough time, it leaked in less than a year.
On Monday afternoon, I received an email from Tony. Tony is a purchasing manager of CASAPPA in Italian, mainly responsible for the purchasing of hydraulic pump components, and the work has been very smooth. Last month, they received a complaint from the largest customer that the pressure at the outlet of the hydraulic pump sometimes rises by itself, resulting in unstable operation of the equipment. The customer's site engineer couldn't solve it and turned to CASAPPA for after-sales service. Although the warranty period has expired, they still need to help customer solve the problem. Their engineers tested various parameters of the hydraulic pump. After comprehensive analysis, they were still uncertain about the root cause, but they suspected that the hydraulic pressure relief valve in the pump is faulty. The engineer asked Tony to contact the original supplier of the hydraulic pressure relief valve and ask him to send a sample of the hydraulic pressure relief valve for replacement and test. It is a local hydraulic valve manufacturer and they still have samples in stock. After receiving samples and commissioning, the engineer's suspicion was proved to be correct. After replacing the hydraulic pressure relief valve, the hydraulic pump worked normally. Tony asked the original hydraulic valve manufacturer to urgently replenish 30 hydraulic pressure relief valves to solve this complaint. The manufacturer said that the shipment has passed the two-year warranty period. At present, there are only 3 samples in stock. The remaining quantity needs to wait in production schedule for production, and can only be delivered after 3 months. If offering this plan to the big customer, Tony would be scolded by the boss. He thought of AAK, because the hydraulic valve failed last year, which was also solved by AAK. Tony established a business relationship with us last October. Now we are also friends besides business. We often discuss the knowledge related to hydraulic valves. His email on Monday is just to ask for help on this hydraulic pressure relief valve. After knowing these conditions, I asked him to send us samples of those faulty hydraulic pressure relief valves, and provide us the drawings of this hydraulic pressure relief valve, noting those special requirements. After receiving and disassembling the samples from Tony, we found that the main valve spool of the hydraulic pressure relief valve was too loose and had increased leakage, then the pressure at the oil outlet increased. The problem should be caused by high-frequency wear or insufficient accuracy of the original shipped hydraulic pressure relief valve. The engineer of CASAPPA asked us to reply why it was determined that it was the problem of the valve spool?
On Monday afternoon, I received an email from Tony. Tony is a purchasing manager of CASAPPA in Italian, mainly responsible for the purchasing of hydraulic pump components, and the work has been very smooth. Last month, they received a complaint from the largest customer that the pressure at the outlet of the hydraulic pump sometimes rises by itself, resulting in unstable operation of the equipment. The customer's site engineer couldn't solve it and turned to CASAPPA for after-sales service. Although the warranty period has expired, they still need to help customer solve the problem. Their engineers tested various parameters of the hydraulic pump. After comprehensive analysis, they were still uncertain about the root cause, but they suspected that the hydraulic pressure relief valve in the pump is faulty. The engineer asked Tony to contact the original supplier of the hydraulic pressure relief valve and ask him to send a sample of the hydraulic pressure relief valve for replacement and test. It is a local hydraulic valve manufacturer and they still have samples in stock. After receiving samples and commissioning, the engineer's suspicion was proved to be correct. After replacing the hydraulic pressure relief valve, the hydraulic pump worked normally. Tony asked the original hydraulic valve manufacturer to urgently replenish 30 hydraulic pressure relief valves to solve this complaint. The manufacturer said that the shipment has passed the two-year warranty period. At present, there are only 3 samples in stock. The remaining quantity needs to wait in production schedule for production, and can only be delivered after 3 months. If offering this plan to the big customer, Tony would be scolded by the boss. He thought of AAK, because the hydraulic valve failed last year, which was also solved by AAK. Tony established a business relationship with us last October. Now we are also friends besides business. We often discuss the knowledge related to hydraulic valves. His email on Monday is just to ask for help on this hydraulic pressure relief valve. After knowing these conditions, I asked him to send us samples of those faulty hydraulic pressure relief valves, and provide us the drawings of this hydraulic pressure relief valve, noting those special requirements. After receiving and disassembling the samples from Tony, we found that the main valve spool of the hydraulic pressure relief valve was too loose and had increased leakage, then the pressure at the oil outlet increased. The problem should be caused by high-frequency wear or insufficient accuracy of the original shipped hydraulic pressure relief valve. The engineer of CASAPPA asked us to reply why it was determined that it was the problem of the valve spool?
mainly responsible for the purchasing of hydraulic pump components. Last October, developed a new hydraulic pump and planned to promote this new product at this year's exhibition. During the debugging, the output pressure of the hydraulic pump can not be established several times, which is a little troublesome, because the owner has sent all the invitations to the exhibition to the customers and grandly introduced the functions of this hydraulic pump. The R & D personnel checked and tested each component one by one. It is basically certain that it is caused by the instability of the pilot operated pressure control valve. The technical team dissected the pilot pressure control valve and found local friction marks on one side of the hole wall of the valve body. The diagnosis conclusion is that the main valve spool is stuck, which should be caused by the concentricity difference between the hole of the main valve body and the hole of the pilot pressure control valve body. to re purchase the pilot pressure control valve that meets the technical requirements, which must be solved within 25 days, otherwise he will leave because the exhibition is too important. the original hydraulic valve manufacturer and got a reply that due to equipment, he could not produce high-precision pilot pressure control valves with the exactly same concentricity. At the same time, he contacted a number of hydraulic valve suppliers and they basically replied that they could not do such a high precision pilot operated pressure control valve, which made almost . When searched the hydraulic valve suppliers in , he found AAK HYDRAULIC VALVE. The details page of the hydraulic valve on AAK made feel that maybe AAK could have a try. He emailed us firstly to ask whether the concentricity of the pilot operated pressure control valve could be consistent. We need the detailed drawings, working conditions and parameters of his whole hydraulic pump to judge. After receiving all information from him, AAK technical team pondered the whole afternoon, with more than 95 confidence, and it would take 15 20 days to complete it. he was happy and uneasy. He was happy that some hydraulic valve manufacturer could try this high-precision pilot operated pressure control valve and has a high probability of success. He was uneasy that if AAK HYDRAULIC VALVE did not succeed in proofing, the time would be wasted. We understand his concern. We told him that the reason why we are not sure for 100 is that there is a data that can't be determined. If AAK HYDRAULIC VALVE failed in sampling, then he should not waste time in Ningbo area. We suggest that he also find a hydraulic valve supplier in Europe, so as to sample with AAK at the same time.