The round jaw design on the S50 Series AC current clamp on CT along with the high content permalloy core makes them well suited for power quality applications where high accuracy and low phase shift along with wide frequency are important from 10Hz to 10MHz. Measurement range is 1mA to 1200A. The S50 clamp on ct is a general purpose 1200A AC current clamp designed for use with DMMs & BNC, power loggers and energy meter calibration instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The S50 clamp on CT has an integral 2.5m lead terminated. The rounded jaw design on this current clamp makes it well-suited for power applications where high accuracy 0.1% and low phase shift and wide frequency response are important.
FEATURES
UL, CE CNAS mark
High content permalloy core
Holding wire diameter: 52mm
Frequency 10Hz-10MHz Bandwidth
Conforms to EN 61010, 600V CAT III
Measurement range of 1mA to 1200A AC
Low phase shift for power measurement
Industrial design & beautiful appearance
Improved ergonomic design & easy operation
High precision 0.1% for current measurement
Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters
The model Q110 ring type current clamp probe is a high accuracy CT, the advanced design ensures enhanced linearity 0.2% and the jaw opening system provides enhanced safety. 110mm large jaw ensures it can measure up to 1000A AC current, Frequency range from 10Hz to 20KHz. It can connect with phase detection analyzer, industrial control equipment, data recorder, oscilloscope, harmonic analyzer, electric power quality analyzer, high precision digital multi-meter & cable fault analysis etc. FEATURES
Product : Pipe clamp Steel grade : SPFH540 Size : 48.6*48.6 / 48.6*60.5 / 60.5*60.5 Pipe clamp are our flagship items since Hory has been producing it in 2010. Currently supplying it to several countries as 'Japan', 'Thailand', 'Russia', 'Cambodia', 'Vietnam', 'Philippines' as well as 'U.S.A'.
Performance testing 1. Mechanical performance: the grip force of the wire clamp is 1/10 bigger than the break force of the lead, It comply with GB2314-1997. 2. Temperature rise performance: under the condition of big current, the temperature rise of connector is less than that of connection lead. 3. Heat circle performance: conforms to GB/T2317.3-2000, the heat circle trial standard for electric fitting. 4. Waterproof insulation performance: conforms to the relevant testing requirements in Part 2 of GB/T13140.4-1998. 5. Resistance to corrosion performance: under the condition of SO2 and salt fog, it can do three times of fourteen days circle testing. 6. Environmental aging performance: under the circumstance of ultraviolet, radiation, dry and moist, expose it with change of temperature and heat impulse for six weeks. 7. Fire-proof performance: insulation material of the connector withstands glowing filament test. Conform to the requirements in Chapter 4-10 of GB/T5169.4. -
ADSS Preformed Suspension Clamp The base is attached by a rear hinge for quick and easy installation of ADSS cables Cushioned pad made of UV resistant neoprene sleeve insert to gently hold the ADSS cable in place Includes stainless steel bolts and locking washers for locking clamps ADSS Suspension Clamp Suspension clamps are also called fixture suspension or suspension fittings. According to the application, the suspension clamps are divided into ABC optical cable suspension clamps, ADSS optical cable suspension clamps, and overhead line suspension clamps. ADSS Optical Cable Suspension Clamp Suspension cleats for ADSS cables are also known as prefabricated suspension cleats. Prefabricated catenary clamps that function the same as ordinary catenary clamps are designed to suspend conductors or ground wires in a vertical direction. Huaneng prefabricated suspension clamps are suitable for high voltage above 220kv. Unique features of prefabricated suspension clips: Effective protection of conductors Avoiding Electricity Waste Due to Corona easy installation Prefabricated suspension clamps are designed to protect ADSS (All Dielectric Self Supporting) cables from sloshing caused by wind currents. Suspended clamps are widely used in transmission lines, towers or power distribution systems. The distance between the two towers is called the span. For short spans, prefabricated suspension clamps with O-rings are often used. This kind of suspension clamp has the characteristics of lightest weight, convenient installation, and can protect ADSS optical cable more effectively. For mid-span and long-span, there is also a prefabricated suspension clamp that is aluminum-clad. The Armor Clip Suspension connects with U-Clips to hang cables. Aluminum-clad suspension clamps support and protect ADSS fiber optic cables from bending damage. According to the span, the short span adopts single suspension clamp, and the long span adopts double suspension clamp. Composition: inner pre-twisted wire, the outer pre-twisted wire, rubber insert, cast aluminum shells, right-angle shackle, U-type shackle. Purposes: supporting cable, make the ADSS hang on the tower.
ADSS Preformed Suspension Clamp The base is attached by a rear hinge for quick and easy installation of ADSS cables Cushioned pad made of UV resistant neoprene sleeve insert to gently hold the ADSS cable in place Includes stainless steel bolts and locking washers for locking clamps ADSS Suspension Clamp Suspension clamps are also called fixture suspension or suspension fittings. According to the application, the suspension clamps are divided into ABC optical cable suspension clamps, ADSS optical cable suspension clamps, and overhead line suspension clamps. ADSS Optical Cable Suspension Clamp Suspension cleats for ADSS cables are also known as prefabricated suspension cleats. Prefabricated catenary clamps that function the same as ordinary catenary clamps are designed to suspend conductors or ground wires in a vertical direction. Huaneng prefabricated suspension clamps are suitable for high voltage above 220kv. Unique features of prefabricated suspension clips: Effective protection of conductors Avoiding Electricity Waste Due to Corona easy installation Prefabricated suspension clamps are designed to protect ADSS (All Dielectric Self Supporting) cables from sloshing caused by wind currents. Suspended clamps are widely used in transmission lines, towers or power distribution systems. The distance between the two towers is called the span. For short spans, prefabricated suspension clamps with O-rings are often used. This kind of suspension clamp has the characteristics of lightest weight, convenient installation, and can protect ADSS optical cable more effectively. For mid-span and long-span, there is also a prefabricated suspension clamp that is aluminum-clad. The Armor Clip Suspension connects with U-Clips to hang cables. Aluminum-clad suspension clamps support and protect ADSS fiber optic cables from bending damage. According to the span, the short span adopts single suspension clamp, and the long span adopts double suspension clamp. Composition: inner pre-twisted wire, the outer pre-twisted wire, rubber insert, cast aluminum shells, right-angle shackle, U-type shackle. Purposes: supporting cable, make the ADSS hang on the tower.
Heavy-Duty Suspension Clamp The Heavy Duty Suspension Clamp serves as a crucial fixture for high current transmission lines, facilitating the suspension of conductors to insulators and tower arms. Its compact and durable design makes it an effective medium for power transmission and enables it to endure high voltage conditions. The galvanized finish ensures exceptional resistance to corrosion. Installation is straightforward, and it is designed to support heavy wires and various conductors. Constructed from premium quality materials, it is capable of withstanding elevated temperatures. The clamping force is sufficiently robust to secure heavy power transmission conductors even in adverse weather conditions and strong winds. Features The Heavy-Duty Suspension Clamp is engineered to deliver exceptional performance and longevity, ensuring the smooth operation of overhead lines. This clamp offers superior support and stability for conductors within power transmission systems, featuring a helical design that securely retains the conductor. Constructed from premium, corrosion-resistant materials, it is built to endure harsh weather conditions. The Heavy-Duty Suspension Clamp is straightforward to install and is compatible with a diverse array of conductors for multiple applications. This advanced solution significantly enhances power transmission systems through its remarkable performance, durability, and ease of installation. Superior Strength High corrosion resistance Durable and maintenance-free Highly versatile Cost-effective Withstands extreme weather conditions Quick and robust setup makes operation easy Neatly packaged on pallets or in wooden crates
Electrical parameters Ratio 1000: 1 or 2000:1 (customized) Accuracy class 0.1%, 0.2%, 0.5%, 1% Primary current 0 - 1000A AC Secondary voltage 0-10V AC (customized) Max. Cont. Input current 1200A Over voltage category CAT III 600V Output signal (AC current) 250mA, 500mA,1A,5A AC at nominal input current Output signal (AC voltage) 1V, 5V, 10V AC at nominal input current Frequency range 40Hz-2000Hz Dielectric strength 3KV 50Hz/60Hz at 1 minute Temperature range '-40C to +55C Output 2.5 meter cable with D01 connector Max. voltage not insulated conductors 600 V Standard EN 61010-1, EN 61010-2-032, IEC60044-1, IEC61869-2 Installation clamp type Output mode lead output(2.5m, 5m or 10m) Mechanical parameters Dimensions (L x W x H) (mm) 163 x 310 x 34 Weight (g) 900 Holding wire diameter (mm) 110 Max. jaw opening (mm) 110 Jaw color Black Material PC+ABS, UL94 V0
ADSS with The DN Short-span Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. Tension Clamp ADSS (All-Dielectric Self-Supporting) tension clamp is a device used to attach and support ADSS cables to poles or towers in overhead fiber optic cable installations. It is designed to grip the cable without damaging it while also providing the necessary tension to keep the cable taut and secure. The ADSS tension clamp is typically made of corrosion-resistant materials such as aluminum or plastic and is available in different sizes to fit various cable diameters. Composition: twisted wire, thimble, PH-type shackle, U-type shackle etc. Purposes: support all strain, make ADSS cable connect the strain pole and tower. Features: Preformed wire connect the pole and tower by thimbles etc. link fitting, afford the load of the transmission line. Grip strength not less than cable 95%RTS in case that not more than lateral pressure of the cable E xcellent aluminum clad steel improve the mechanical and resist-corrosion function, extend life. Corrosion-resistant materials such as aluminum or plastic to ensure durability and longevity. Gripping mechanism that securely holds the cable without causing damage. Tensioning mechanism that allows for adjustment of the cable tension. Insulating material to protect the cable from electrical currents. Suitable for use with a range of cable diameters. Easy installation and maintenance. Technical requirements: meet the DL / T 766-2003 ADSS with the preformed helical fittings technical requirements and test methods
CM500A 600A AC Clamp Meter CM510A 600A AC Clamp Meter (Temperature function) CM520A 400A DC/AC Clamp Meter CM530A 600A DC/AC Clamp Meter CM550A 1020KVA Power DC Clamp Meter CM210C 20.00A~200A DC/AC Mini Clamp Meter CM210E 2.000 A~200A DC/AC Mini Clamp Meter CTA600 600A AC A Current Clamp Meter Module
