A quick drying two pack polyurethane super gloss topcoat for application over wood & wood substitute with excellent gloss & finish.This is a higher solid formulation hence a single coat application over sealer is adequate for low grain profile substrate. On full
cure the product forms a very hard & flexible film with outstanding light fastness, chemical resistance & mechanical properties including mar /scratch resistance guaranteeing a long-term protection of wood.
PU Clear Gloss 100%
MATT/GLOSS 10%, 30%, 50%
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
A quick drying two pack polyurethane sanding sealer for application over wood & wood substitute with excellent sealing & sanding property. The product has high penetrating power & superior filling property enabling it to perform as filler cum sealer Single coat application is adequate for low grain profile substrate. On full cure the product forms a tough flexible film with outstanding chemical resistance & mechanical properties & can withstand dimensional variation of wood due to moisture ingress. When used in combination with Maxiwood PU Gloss, Silkmatt/Matt Topcoat the system gives a very rich finish with excellent resistance properties.
A two-pack polyurethane quick drying primer cum surfacer with excellent filling & sanding properties for application on wood (hard & soft) & wood substitutes like particle board, veneer, plywood etc. The formulation contains mixed isocyanate hardeners, inert & smooth sanding extenders. When used in combination with Maxiwood 2 PK PU Topcoat, the product gives an extremely rich finish. Presence of plasticizer in the formulation of Maxiwood 2 PK PU Primer Surfacer make the product flexible enough to withstand woods dimensional variation thus enhancing adhesion.
PU SEALER THIXOTHROPIC PU CATALYST CO15 PU CLEAR MATT GLOSS THIXOTHROPIC PU WHITE PRIMER THIXO
Pu Sealer-white Primer -pu Clear 10%, 30%, 50%, 100% Gloss, Full Gloss
Ritver Powder Coating is a Italian product manufactured in Dubai UAE for Africa and Asia markets. Powder coating is categorized in: Class 1,2 and 3 (for metal intrusions- aluminium, cast iron and steel) Class 1 POLYESTER : Standard Powder Coating with upto 150 color codes as per RAL systems with a warranty of up to 20 years Class 2 EPOXY: Super Durable (for exterior and interior) for up to 45 RAL color shades Class 3 EPOXY-POLYESTER:Hyper Durable (for high end structures to protect from UV), Recommended for high rise structures, aviation and metro- locomotive industries Available in Full Gloss: 90/Gloss: 77/Semi Gloss: 35/Matt: 25/Dead Matt:15% in soft textured, standard texture and coarse finishes Product is available in 20kg packing
Ritver Powder Coating is a Italian product manufactured in Dubai UAE for Africa and Asia markets. Powder coating is categorized in: Class 1,2 and 3 (for metal intrusions- aluminium, cast iron and steel) Class 1 POLYESTER : Standard Powder Coating with upto 150 color codes as per RAL systems with a warranty of up to 20 years Class 2 EPOXY: Super Durable (for exterior and interior) for up to 45 RAL color shades Class 3 EPOXY-POLYESTER:Hyper Durable (for high end structures to protect from UV), Recommended for high rise structures, aviation and metro- locomotive industries Available in Full Gloss: 90/Gloss: 77/Semi Gloss: 35/Matt: 25/Dead Matt:15% in soft textured, standard texture and coarse finishes Product is available in 20kg packing
