Stainless Steel, Titanium, Hastealloy, Nickel, Inconnel Tongue Groove Flanges.
Stainless Steel, Titanium, Hastealloy, Nickel, Inconnel Tongue Groove Flanges.
Supplier: Flanges, grooved fittings, valves
A split flange is a type of flange that can be easily installed on pre-existing piping. It is made up of two interlocking pieces that fit securely together using nuts and bolts or welding it into place. Because it is made of two parts, split flanges are used to reinforce weakened areas of piping, or to add an attachment in places conventional flanges cannot. Split-flange fittings use rubber O-rings to seal joints and contain pressurized fluid. The O-ring sits in a groove on the flange, and then mates with a port's flat surface. The flange is then attached to the port with four mounting bolts. The bolts tighten downward onto the clamps of the flange, thereby eliminating the need for large wrenches to connect the components of large-diameter tubing.
A threaded flange is a type of flange that uses a screw thread to connect the flange to a pipe. A male thread is cut onto a pipe end whilst a female thread is cut into the bore of the flange; the male threaded pipe is then screwed into the female threaded flange. Threaded flanges are available in a variety of sizes and pressure ratings, and are typically made from Various Materials. Technical Specifications 1. Materials: Carbon steel, stainless steel, alloy steel, 2. Size: �½ inch to 24 inches 3. Classes: 150, 300, 400, 600, 900, 1500, 2500 4. Thread type: NPT, BSP, BSPT, BSPP 5. Face type: Flat, Raised and Ring Joint 6. Dimensions: ANSI B16.5, ASME B16.47, Advantages of Threaded Flanges: A. Easy to install and maintain B. No welding required C. Suitable for a variety of applications D. Available in a variety of sizes and pressure ratings Applications: Threaded flanges are used in a variety of applications, including: a. Water and wastewater systems b. Oil and gas pipelines c. Chemical processing plants d. HVAC systems e. Fire protection systems
A spectacle blind flange is a safety device used to isolate a section of pipeline or equipment when they need to be inspected or removed from piping system. It is not like a valve, the spectacle blind flange is a permanent or long term isolation block. The spectacle blind flange is made of two pieces metal discs which are joint together by a part of steel handle. The two discs are connected by a hinge, so that the blind flange can be rotated to open or close the pipeline. Technical Specifications a. Material: Carbon steel, stainless steel, alloy steel b. Standard: ASME B16.47 c. Face type: Raised face (RF), flat face (FF), ring type joint face (RTJ) d. Size: 12/â?? to 24â?? e. Pressure rating: 300,600,900,1500,2500 Lbs Features A. Easy to install and remove B. Permanent or long term isolation C. Cost-effective alternative to isolation valves D. Wide range of materials and sizes available Applications A. Pipelines B. Process equipment C. Boilers D. Tanks E. Vessels Benefits 1. Safety: Prevents accidental release of fluids or gases 2. Cost-effectiveness: More affordable than isolation valves 3. Convenience: Easy to install and remove 4. Durability: Made from high-quality materials
DIN Standard Flanges are a type of flange that is manufactured to the DIN (Deutsches Institut Normung) standard. DIN flanges are available in a variety of styles, including slip-on, weld-neck, blind, threaded, and socket weld. They are made from a variety of materials, including carbon steel, alloy steel, and stainless steel. DIN flanges are used in a wide range of applications, including industrial piping systems, pressure vessels, and boilers. Technical Specifications A. Pressure rating: From PN6 to PN40. B. Temperature rating: From -20'C to +250'C. C. Material: Carbon Steel, Alloy Steel, and Stainless Steel. D. Finish: DIN flanges are available in a variety of finishes, including hot dip galvanized, painted, and stainless steel. Applications DIN Standard Flanges are used in a wide range of applications, including: 1. Industrial piping systems 2. Pressure vessels 3. Boilers 4. Tanks 5. Valves 6. Fittings Advantages Some of the advantages of DIN Standard Flanges include: I. They are manufactured to a high standard of quality. II. They are available in a variety of styles and materials. III. They are compatible with a variety of other piping components. IV. They are relatively easy to install and maintain.
Carbon steel flanges are a type of flange that is made of carbon steel. Carbon steel is a type of steel that contains carbon as its primary alloying element. Carbon steel flanges are typically used in applications where strength and durability are important. They are also relatively inexpensive, making them a cost-effective option for many applications. Technical Specifications 1. Material: Carbon steel 2. Size: �½ Inch to 24 Inch 3. Type: RF, FF, RTJ 4. Pressure rating: Class 150 to 2500 5. Temperature range: -200�°F to 1200�°F 6. Finish: Black, mill scale, or hot dipped galvanized 7. Dimensions: ANSI/ASME B16.5, DIN 2533, or MSS SP-44 Applications a. Oil and gas pipelines b. Chemical processing plants c. Power plants d. Water treatment facilities e. HVAC systems Advantages 1. Strength 2. Durability 3. Inexpensive 4. Wide variety of applications
Mild Steel Flanges are a type of flange made from mild steel. Mild steel is a low-carbon steel that is strong and ductile, making it a good choice for flanges that need to be able to withstand high pressures and temperatures. Mild Steel Flanges are typically used in a variety of industries, including the oil and gas industry, the chemical industry, and the water treatment industry. Technical Specifications 1. Material: Mild Steel 2. Size: ½ Inch to 24 Inch 3. Type: RF, FF, RTJ 4. Pressure rating: Class 150 to 2500 5. Carbon Content: 0.05%-0.25% 6. Yield Strength: 370 MPa 7. Tensile Strength: 440 MPa 8. Hardness: 126 Brinell 9. Temperature Rating: Up to 500�°F 10. Dimensions: ANSI/ASME B16.5, DIN 2533, Other Features Mild Steel Flanges are available in a variety of sizes and styles, including slip-on flanges, weld neck flanges, and socket weld flanges. They can also be finished in a variety of ways, including hot dip galvanizing, painting, and powder coating. Applications a. Oil and gas industry b. Chemical industry c. Water treatment industry d. Power generation industry e. HVAC industry f. Marine industry Advantages A. Strong and ductile B. Affordable C. Widely available D. Easy to fabricate E. Can be finished in a variety of ways
