Gear Reducer:
Double helical involute, double reduction. Its unique features result in a gear reducer that can withstand heavy cyclic loads and provide years of service with minimal maintenance. Meets or exceeds API 11 The torque rating of the gears shall be as determined by API Specification 11E and AGMA Specification 422.03.
-All pinions and shafts shall be made of 4145 high alloy steel. Material certifications are required.
Gear Reducer Housing:Gear Reducer is a two piece housing is ASTM A48 gray iron casting
Gear Reducer Lubrication:An exclusive feature of every VENDOR unit is its gearbox Positive oil lubrication system. This unique system should uses oil buckets to fill troughs that continuously feed the right amount of oil to each gearbox bearing, regardless of the direction of rotation, at pumping speeds as low as 1 strokes per minute without modification (wipers not required). The reducers oil capacity should be large enough to operate with no sump. Meets API 11E
NB:Gear reducers shall be shipped full of oil and ready to be placed into operation
High/Intermediate/Low Speed Bearings:The gear reducer should contains properly sized anti-friction bearings, rather than energy-consuming bronze bushings. Each bearing is set in a carrier for ease of removal and installation. Should meets or exceeds API 11E
Gear Reducer Seals:High and Low speed shaft should use Butadiene acrylonitrile rubber seals. Meets AP111E Section 7.4.9
Gear Reducer: Double helical involute, double reduction. Its unique features result in a gear reducer that can withstand heavy cyclic loads and provide years of service with minimal maintenance. Meets or exceeds API 11 The torque rating of the gears shall be as determined by API Specification 11E and AGMA Specification 422.03. -All pinions and shafts shall be made of 4145 high alloy steel. Material certifications are required. Gear Reducer Housing:Gear Reducer is a two piece housing is ASTM A48 gray iron casting Gear Reducer Lubrication:An exclusive feature of every VENDOR unit is its gearbox Positive oil lubrication system. This unique system should uses oil buckets to fill troughs that continuously feed the right amount of oil to each gearbox bearing, regardless of the direction of rotation, at pumping speeds as low as 1 strokes per minute without modification (wipers not required). The reducers oil capacity should be large enough to operate with no sump. Meets API 11E NB:Gear reducers shall be shipped full of oil and ready to be placed into operation High/Intermediate/Low Speed Bearings:The gear reducer should contains properly sized anti-friction bearings, rather than energy-consuming bronze bushings. Each bearing is set in a carrier for ease of removal and installation. Should meets or exceeds API 11E Gear Reducer Seals:High and Low speed shaft should use Butadiene acrylonitrile rubber seals. Meets AP111E Section 7.4.9
Gear Reducer: Double helical involute, double reduction. Its unique features result in a gear reducer that can withstand heavy cyclic loads and provide years of service with minimal maintenance. Meets or exceeds API 11 The torque rating of the gears shall be as determined by API Specification 11E and AGMA Specification 422.03. -All pinions and shafts shall be made of 4145 high alloy steel. Material certifications are required. Gear Reducer Housing:Gear Reducer is a two piece housing is ASTM A48 gray iron casting Gear Reducer Lubrication:An exclusive feature of every VENDOR unit is its gearbox Positive oil lubrication system. This unique system should uses oil buckets to fill troughs that continuously feed the right amount of oil to each gearbox bearing, regardless of the direction of rotation, at pumping speeds as low as 1 strokes per minute without modification (wipers not required). The reducers oil capacity should be large enough to operate with no sump. Meets API 11E NB:Gear reducers shall be shipped full of oil and ready to be placed into operation High/Intermediate/Low Speed Bearings:The gear reducer should contains properly sized anti-friction bearings, rather than energy-consuming bronze bushings. Each bearing is set in a carrier for ease of removal and installation. Should meets or exceeds API 11E Gear Reducer Seals:High and Low speed shaft should use Butadiene acrylonitrile rubber seals. Meets AP111E Section 7.4.9
Housing material is high density aluminium alloy ADC-12. Gear profile type ZK which efficiency up to 0.9. Other China made gear profile type is in ZA which efficiency up to 0.7 only. Hobbing tools for ZK profile are much expensive more than 10 times than ZA. Material of worm shaft is 40Cr (ASTM 5140). Others makers are using 45# steel which quality is poor while using it as worm shaft. Material of brass on worm wheel is ZQSnD10-1 (DIN GB-CuSn10/2.1051)(BS PB1) which other China makers are using ZQSND9-4 only. Bearings from FAG bearings China OEM makers. Synthetic lubrication oil of TAXAS brand. 100% running test before ex-factory.
High transmission efficiency. A single machine can reach a transmission efficiency as much as 96%; Precise division of transmission ratio with a wide range.The combination of machines can produce a larger transmission ratio at a low output rotate speed. Various ways of installation. Horizontal installation at any position or flanged installation. Wooden case
Gear reducer
Worm gear reducer Excellent performance, simply structure, small cubage and high efficiency.
Gear size 25 ~ 150 Ratio 5 ~ 100 Power 0,12 ~ 15 kW Torque range 5 ~ 2.000 Nm
Type Input Speed Range (RPM/Min) Reduction Ratio Torque Range Nm Output Shaft Std Unit Height Unit Width Unit Weight (kg) OMH3 95~630 3.5-1 2000 SAE Flange 2" Hex 315mm 170mm 20.25 OMH4 95~630 3.75- 1 2000 SAE Flange 2" Hex 330mm 240mm 28.35 OMH5 95~630 3.86- 1 2500 SAE Flange 2" Hex 350mm 245mm 36.65 OMH6 95~630 4.5-1 2000 SAE Flange 2" Hex 395mm 280mm 38. 15 OMH6 95~630 4.5-1 2000 SAE Flange Flange 290mm 285mm 39.40
Power: 5~6666 kw Transmission ration range: 1.25~500 Output torque: 450~130000 n.M Output speed: 134~1200 r/min Characteristics: 1. The gear is made of high strength low carbon alloy steel through carburization and quenching. The hardness of tooth surface may reach to hrc5862. All gear adopts nc tooth grinding process, high in accuracy and good in contact performance, 2. Highly transmission efficiency: single stage, more than 96.5%; doublestage, more than 93%; threestage, more 90%; 3. Smooth and stable in run, low noise; 4. Compact size, light weight, long service life and high load capacity; 5. Easy to disassemble, inspect and assemble. Main models: Zdy80, zdy100, zdy125, zdy160, zdy200, zdy250, zdy280, zdy315, zdy355, zdy400, zdy450, zdy500, zdy560 Applying industries, This product is widely applied to fields of metallurgy, mines, hoisting, transportation, cement, architecture, chemical, textile, printing.
