Rope Grab Fall Arrester

UB2009 Guidedtype Fall Arrester Made of alloy steel In built gravity lock to avoid incorrect use In event of fall quickly grips the rope works on 14 mm dia polyamide rope Conforms to EN 353-2. For price, specification and other details please contact us.

UB2011 Guidedtype fall arrester made of high strength steel in built gravity lock to avoid incorrect use in event of fall quickly grips the rope detachable ropegrab device works on 14mm dia polymaide rope. conforms to EN 353-2 For price, specifications and other details please contact us

Supplier: Pressed sheet metal components, assemblies and machined components, Metal Fittings for Harness and Fall Arresters, Cargo Lashing/Tie Down/Ratchet Lashings

A flame arrester (also spelled arrestor), deflagration arrester, or flame trap is a device that stops fuel combustion by extinguishing the flame. A flame arrester (also called a deflagration arrester) functions by absorbing the heat from a flame front traveling at sub-sonic velocities, thus dropping the burning gas/air mixture below its auto-ignition temperature: consequently, the flame cannot survive. The heat is absorbed through channels (passages) designed into an element. These channels are chosen and measured as the MESG (Maximum Experimental Safe Gap) of the gas for a particular installation. These passages can be regular, like crimped metal ribbon or wire mesh or a sheet metal plate with punched holes, or irregular, such as those in random packing. Principle Flame arresters are passive devices with no moving parts. They prevent the propagation of flame from the exposed side of the unit to the protected side by the use of metal matrix creating a torturous path called a flame cell or element. All detonation flame arresters operate on the same principle: removing heat from the flame as it attempts to travel through narrow passages with walls of metal or other heat-conductive material, but unlike flame arresters, detonation flame arresters must be built to withstand extreme pressures that travel at supersonic velocities, 1,500 psi (10 MPa) at 2500 m/s is not uncommon with a group D Gas.

Supplier: Copper (Sheets, Rods, Pipes, Strips, Lightening Arresters, Ropes, Wires) Brass (Rods, Pipes, Strips, Busbars, Angles, T Angle, U Shaped Strips, Sheets) Aluminium (Rods, Pipes, Angle, Busbars, Wires) Gun Metal, Zinc, Tin, Lead, Antimony And Earth Powder
Buyer: Copper (Sheets, Rods, Pipes, Strips, Lightening Arresters, Ropes, Wires) Brass (Rods, Pipes, Strips, Busbars, Angles, T Angle, U Shaped Strips, Sheets) Aluminium (Rods, Pipes, Angle, Busbars, Wires) Gun Metal

Supplier: Electrical appliance involves series of vacuum circuit breaker, outdoor h.V. Falling fuse box, lighting arrester, outdoor isolating switch, indoor load switch, synthetic rubber insulator

Supplier: Shell and tube heat exchanger, spiral heat exchanger, tube in tube heat exchanger, rotameter, u tube manometer, pressure vessel, safety valve, pressure relief valve, thermal energy storage system, ibr valve, air cooled heat exchanger, oil cooler, box type heat exchanger, finned tubes, evaporative condenser, tube bundles, condenser coils, industrial filters, cooling tower, dehumidifiers, fan coil unit, air handling unit, industrial chillers, chilling plant, iqf tunnel freezer, jacketed vessel, storage tanks, dosing system, gas metering and regulating station, thermic fluid heater, economizer coils, multi effect evaporator, falling film evaporator, oil flow meter, mass flow meters, level indicators, pressure flow level switch, radar level, plate heat exchangers, magnetic level indicators, ice plants, flame arresters, cold storage, fin fan cooler, dairy process equipment, waste heat recovery system, industrial chemicals, flame arrester, industrial boilers,

Low & High Voltage Silicon Rubber Insulator Long Rod Composite Suspension Insulator Manufacturer Composite Suspension Rod Insulator (Export Type) Installation Instruction: 1. The transportation and installation of the insulator shall be taken good care without any throwing or collision, fiction with various sundries(wires, iron plates and tools etc.) and solid material. 2. When suspending the composite insulator, the knot shall be made on the attachment at the end. Knot on shed or sheath are strictly prohibted. When the rope has to be contacted with shed or sheath, the contacting area shall be packed with soft cloths. 3. Never apply the composite insulator as the assistant tool for the wire distribution and collecttion and collection in case that the insulator can be damages by impact or bending moment. 4. Do not step on the insulator shed with foot. 5. When installing the grading ring, attention shall be attached on the adjustments to make sure that the ring is vertical with the axial of the insulator. And for opening grading ring, the openning directions at both ends shall be consistent to facilitate the discharging and protect the shed. ______________________________________________________________________________ This's Jack from Nengxing Electric Power Equipment (China). We're an innovative high-tech enterprise integrating Rï¼?D, production, service and construction of surge arrester, composite insulator, fuse cut-out, etc. (as the attached pictures) We undertake a national technical project and supply for the State Grid of China.