it is made of SS304 material
it is used in heavy duity worm drive clamp
it can be also used in Tbolt clamp
it has four milling slots
also has threading og 1/4 unf 28 TPI
it is made of SS304 material it is used in heavy duity worm drive clamp it can be also used in Tbolt clamp it has four milling slots also has threading og 1/4 unf 28 TPI
Tee Slot Nut Features Cold drawn T-nut features unique undercut to prevent interference from T-slot burrs. Stud stays perpendicular to the table. Bottom chamfer (approximately 60 off horizontal) clears chips for easy insertion. Threads are roll formed for more holding power and last thread is incomplete to prevent T-slot or table damage.
APPLICATIONS The Slotted Round Nut is used across severalapplications including electrical engineering.They can be tightened by means of a slottedscrewdriver and are intended to be used forlocking components where no specific prestressing forces are required. Slotted nuts are used in applications wherevibration or motion might undo the locknut
Slotted Round Nuts
Slotted & Castle Nuts
Slotted/Castle nuts are pre-drilled, they can be used without a pilot hole. These nuts are slotted, allowing them to be installed and removed using screw drivers. It is used primarily as safety nuts, these nuts are slotted to receive a cotter pin or wire which passes through a drilled hole in the bolt and locks it. When a castle nut is applied to a threaded section, it is tightened so that its slot is aligned with a predrilled hole in the bolt or threaded rod, into which a cotter pin, split pin, a lock wire or a spring pin is typically inserted to stop the nut from rotating. Sometimes they are used on trailers too. They are also used as hub nuts that hold the driveshaft within the wheel hub assembly. At HELLARY it is available in stainless steel, carbon steel, and alloy steel to bear more wear and tear while also making it more corrosion resistant.
it is made of ss304 material it is avaliable in set of two pieces of male and female with internal threading of m6 and m8 as per requirment
Nuts are mechanical fasteners with threaded holes. It is attached to a bolt, screw or stud to provide clamping force and prevent axial movement. For example a bolt is inserted through two parts with aligned holes and a nut is then screwed unto the bolt. Types of nuts we can design, manufacture and supply are the following listed below: (1) FLANGED LOCKING NUTS (2) CAGE NUTS (3) STEEL/BRONZE CYLINDERICAL TRAPEZOIDAL LEADSCREW NUTS (4) METRIC CYLINDRICAL CONNECTOR NUTS (5) SOCKET COUNTERSUNK BARREL NUTS (6) HEXAGON NYLON LOCKING NUTS (7) METAL LOCKING NUTS (8) STEEL CYLINDRICAL TRAPEZOIDAL LEADSCREW NUTS (9) CAP NUTS (10) METRIC HEXAGONAL STUD CONNECTOR NUTS (11) SLOTTED ROUND NUTS (12) PIPE NUTS (13) SHEAR NUTS (14) TEE NUTS (15) METRIC DOME NUTS (16) FLANGED TRAPEZOIDAL LEADSCREW NUTS
Nuts Hex nuts, Heavy Hex Nuts, Slotted Hex Nuts, Nylon Insert Lock Nuts, Hex Flange Nuts, Hex Coupling Nuts, Acorn Nuts, Spring Nuts, Ferrules, Wing Nuts, T-Nuts, Kep Nuts, Conical Hex Nuts, Zinc Alloy Insert Nuts, Blind Nuts, Pipe Nuts, Wheel Nuts Hexagonal NutsM6 TO 64MM (1/4" to 2.5") Structural Steel NutsM6 TO 64MM (1/4" to 2.5") Slotted & Castle NutsM6 TO 64MM (1/4" to 2.5") Slotted & Castle Nuts (thin)M6 TO 64MM (1/4" to 2.5") Nuts as per customersM6 TO 64MM (1/4" to 2.5") Drawings / SpecificatonsWe can manufacture any type of typical Fasteners as per your drawing and specifications FINISH : The above products are available in finish like Phosphate, Black Oxide, Galvanised, Hot Dip Galvanised, Cadmium Plating. Teflon (PTFE), Powder & many more as per Customer Requirements. We can also supply fasteners according to customers drawings and specifications. â?¢Washers High tensile and Stainless Steel Fasteners as per National, International Standard & Customer Drawings, We are manufacturer of Washers, Spring Lock Washers, Flat / Plain Washers, Cup Washers. Plain Washers (Steel)M6 to 64mm (1/4" to 2.5") Steel Heavy WashersM6 to 64mm (1/4" to 2.5") Hardened & TemperedM6 to 64mm (1/4" to 2.5") Steel Washers Spring Lock washers Flat / Plain washers Cup washers Drawings / SpecificationsWe can manufacture any type of typical Fasteners as per your drawing and specifications
