1) Mortise Locks 2) Pad Locks 3) Cam Locks 4) Safe Locks 5) Furniture Locks 6) Euro Cylinder Locks 7) Multipurpose Locks 8) Pin Locks 9) Door Locks 10) Night Latch Locks 11) Door Handles 12) Pull Handles 13) Mortise Handles 14) Glass Handles 15) Cabinet Handles 16) Door And Cabinet Konbs 17) Wall Hooks 18) Coat Hooks 19) Door Fittings 20) Hinges 21) Tower Bolt 22) Furniture Hinges 23) Aldrops 24) Door Knowcker 25) Door Stopper 26) Door Closer 27) Bathroom Fittings
All types of construction hardware available. Stainless steel, brass, aluminium, etc.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
All types of construction and marine hardware OEM from our China factory.
Builder hardware Trying our level best to make necessary improvements every day. Depends upon the product
Hardware Lock : It is a parallel port dongle used for software protection. Supports all popular programming languages on DOS, Windows and Windows NT/2000
-one set of toilet cubicle hardware including: 2 pcs support leg;1 pc indicator lock; 1 pc handle; 1 pc coat hook; 3pcs hinge;12 pcs bracket;(above hardwares are high quality nylon material or 304ss) And 2 pcs door stopper;1pc headrail.(above profile are alu.) Some project may also need hanging clapm, flange... -the toilet door is hpl panel. Normally the panel is 10mm/12mm/13mm/18mm/19mm thick.
Supplier: Brass components ,brass precision part,brass cable glands, brass molding insert,brass stop plugs,brass ppr inserts,brass hardware, brass & metal nozzles,brass nipples, brass sanitary part,brass bush and brass products,brass anchors & fasteners, brass lock nut & check nuts & dome nuts, brass turned components,brass inserts, brass auto parts, brass threaded stud, brass forging components, brass forging metal turning parts, brass shower header wall bracket socket,brass electrical components,brass shower hinges pipe to glass connector,brass shower header clamp,brass knob,brass pipe bush,brass guide bush,brass parts,brass tuned components,brass and metal precision parts,brass,ms,ss elbow fitting,brass terminal box connector,brass tee,brass,ms,ss,aluminium stand off(spacers),brass&ms&aluminium &steel metal adapter,brass&ms & aluminium & steel precision turned components,brass & ms& aluminium & steel & metal nuts, bolts, washers, zinc (zamak,mazak) metal parts, brass & ms, ss, zinc, aluminium
Services: Manufacturer & exporter
1. Various architectural hardware 2. Various metal processing parts 3. By samples or drawings 4. Die design and manufacture. Carton.
Life-Nature Hardware Hardwares are faucets, door trim, sprinklers 4" x 3"
