KRD11 series pneumatic vertical shock/bump test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests. 1. Pneumatic drive, simple structure and high reliability 2. Pollution free, without hydraulic leak risk and keep the environment clean. 3. Pneumatic drive greatly improves the shock test efficiency, maximum shock rate up to 120 times / min. 4. It can easily realize large pulse width and small overload test. 5. With a fast shock rate comparing to motor or hydraulic driven collision table, it has higher reliability and better collision waveform. 6. The speed and rate of shock can be easily controlled by adjusting the gas pressure. 7. IPS-2000 series shock control and measurement system can perform manual shock, continuous shock, single shock, and interval shock. 8. Built-in brake mechanism ensures the safety of operation in any situation. Technical Specifications KRD11 5 KRD11 15 KRD11 25 KRD11 50 KRD11 100 KRD11 200 KRD11 400 KRD11 600 KRD11 800 KRD11 1000 KRD11 2000 Rated Load (kg) 5 15 25 50 100 200 400 600 800 1000 2000 Table Size (mm) 150 150 200 200 300 300 500 500 600 600 800 600 800 800 1000 800 1000 1000 1200 1200 1500 1200 Peak Acc. (g) Half-Sine 5-2500 5-2000 5-1500 10-750 10-600 10-450 10-400 10-300 10 300 10 250 10 150 Post-Peak Sawtooth 10-200 10-100 10-50 Trapezoid / 15-200 15-100 15-60 15-50 Pulse Duration (ms) Half-Sine 0.4 40 0.5 40 0.6 60 1.5 60 2 60 2.5 60 3 60 3.5 60 4 60 4.5 60 6 60 Post-Peak Sawtooth 3 18 6 18 Trapezoid / 3 18 6 18 Bump Waveform (Optional) Half-sine Waveform Bump Peak Acceleration g 5~150 5~120 5~100 5~80 5~60 5~40 / Bump Pulse Duration (ms) 2~30 3~30 4 ~ 30 5 ~ 30 / Bump Rate (Times/Min) 10~120 10~100 10~80 10~60 10~40 10~30 / Overall Dimension (mm) 1000�?1000�?2100 1000�?1000�?2160 1510�?1300�?2400 1690�?1240�?2350 1710�?1160�?2350 1910�?1500�?2700 1910�?1500�?2500 1900�?1500�?2450 2000�?1500�?2450 1900 1800 2550 2200 1800 2550 Weight (kg) 1300 2300 3000 3070 3900 4500 5000 5200 5600 6200 7300 Working Environment Temperature range 0 ~ 40â??, Humidity 80% (non-condensing) Power 1-phase AC220V�±10% 50Hz Air source 0.8MPa Installation Condition Foundation-free, the cement floor shall be leveled and the working distance of 800~1000mm shall be reserved around the equipment Standards MIL-STD-810F IEC68-2-27 MIL-STD-202 MIL-STD-750 MIL-STD-883 UN38.3 IEC62281 IEC62133-2 UL2054 IEEE1625 SAEJ2929 IEC62660-2 ISO12405-3 UL2580