Qj submersible pumps parameters: Flow range10~500m3/h, lift scope within 5~405m; Caliber scope 32~203mm, temperature range-15~80° c. Products overview: Qj series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: Qj submersible pumps use conditions 1. 380 v bias voltage does not exceed + -5% and 50 hz frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° c, qjr-temperature hot water pump up to 80 ° c. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water ph 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / l.
What is Solar Water Pump : It's a Cost-effective, Reliable and Green solution for providing Water to remote locations where Electrical Supply is not available. It works by converting available solar energy to electrical energy and there by running motors coupled with pumps with that to lift underground water / to pump from sources like Underground water tanks ,Rivers and Lakes. Description : We deal with Solar pumps of various types ranging from 3 H.P. to 20 H.P. capacities Solar PV Cells / Modules are generally installed along with Water pump , Pump Controller / Drive (VFD) forms the whole system Remote operation through mobile application is also available Solar Modules can also be used to cover underground water tanks so that water temperature will also be maintained Types of Solar Water Pumps : Based on Function : Submersible Solar Pumps : These are designed to operate underwater They are used to Pump water from undergrounds/wells / underground water tanks Surface Solar Pumps : These are designed to operate on/ from the surface level of water These are generally used to pump water from shallow wells/rivers / lakes Based on type of Electrical Supply : AC Solar Pumps: These are designed to operate on AC (Alternating Current ) instead of DC (Direct Current ) These are generally used in applications where high flow rate and high-pressure output are required DC Solar Pumps: These are designed to operate on DC (Direct Current) These are generally used in applications where low flow rate and low-pressure output are required Applications : Agriculture Domestic Water Supply Community Water Supply Livestock Management Swimming Pools Hotels Fountains & Waterfalls Chiller Plants Ice Plants Concrete / Batching Plants Food Processing Plants Warranty Terms: Solar Modules come with a warranty of 15 years and an efficiency guarantee of 25 years Pumps and controllers warranty varies from 2-5 years based on the type and capacity of pumps
Monoblock pumps - Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features - High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Inbuilt thermal overload protector in al single phase pumpsets upto 2.0 HP - Specially designed for wide voltage operation - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life - Back pull-out design for easy servicing and repair - Double shielded ball bearings, so no need of external lubrication - All Model fitted to Mechanical seal. specification - Power Range : 0.37Kw - 1.5 Kw (0.5 HP - 2.0 HP) - Version : Single Phase, 220-240V, 50Hz AC Supply Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 32 Mtr. - Maximum Flow Rate : 940 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Mechanical Seal - Type of Duty : S1 (Continuous) - Method of Starting : Permanent Split Capacitor (PSC) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 25 X 25, 32 X 25, 40 X 32, 40 X 40, 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 (All size in mm) characteristics of clear cold water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Mechanical Seal : Carbon & Ceramic Motor Shaft : EN-8 Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Plastic
Monoblock Pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. salient features High operating efficiency resulting in lower power consumption - Good suction lift characteristics - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. - Mechanical seal is provided as per customers requirement Specification - Power Range : 2.2 Kw - 11.2 Kw (3.0 HP - 15.0 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 2880 RPM - Maximum Total Head : 65 Mtr. - Maximum Flow Rate : 1450 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase, Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 50 X 40, 50 X 50, 65 X 50, 80 X 65, 80 X 80 100 X 80 and 100 X 100 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 mÃ?/sec (max.) - Ph Value : 6.5 to 8.5 Material of construction - motor Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminium
Monoblock pumps Falcon centrifugal monoblock pumpsets are powered by a totally enclosed fan cooled AC induction two pole motor. Motor stator is made of low watt loss silicon steel laminations assembled under pressure and rigidly locked in the frame. The windings are of high-grade enameled copper wire offer excellent resistance and are varnish impregnated. Construction of motor frame and usage of quality materials result in high performance and low temperature rise thereby increasing the life cycle of the motor. Salient Features High operating efficiency resulting in lower power consumption. - Good suction lift characteristics. - Specially designed for wide voltage operation. - Dynamically balanced rotating parts including rotor and impeller ensures minimum vibration and longer life. - Back pull-out design for easy servicing and repair. - Double shielded ball bearings, so no need of external lubrication. specification - Power Range : 1.5 Kw - 5.5 Kw (2.0 HP - 7.5 HP) - Version : Three Phase, 380-415V, 50Hz AC Supply - Speed : 1440 RPM - Maximum Total Head : 12 Mtr. - Maximum Flow Rate : 3160 LPM - Maximum Suction Lift : 7 Mtr. - Degree of Protection : IP 44 - Class of Insulation : B0 - Maximum Ambient Tem. : 40 C - Sealing : Stuffing Box - Type of Duty : S1 (Continuous) - Direction of Rotation : Three Phase - Electrically Reversible - Nominal Pumpset Size (Suction X Delivery in inch) : 80 X 80, 100 X 100, 125 X 125, 150 X 150 (All size in mm) Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5 Part Name Material Gland Dori : Graphite String Motor Shaft : EN-19 with SS SLEEVE Motor Body : FG-250 Bearing : SKF End Cover : FG-250 Bracket : FG-250 Flange : FG-250 Casing : FG-250 Impeller : FG-250 Cooling Fan : Aluminum
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Easy Opening Fresh Coconuts from Vietnam is an organic, young, coconut containing fresh coconut water and delicious coconut meat. It is kept in its original shell to still provide its natural taste and flavor, all the nutrients and minerals. With the easy opening experience, you can enjoy our coconuts anywhere, simply press and pull the first opening and drink the healthy coconut water and after lift the second opening with your finger and indulge into the nice coconut meat with a spoon or your fingers.
Flow: 25m3/h Head: 91m Power: 11kw Material: cast iron Medium: clean water Outlet dia: 60mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue Deep well submersible water pump Overview: Filed with: water Flow range: 10—250m3/h; Head range:5—121m; Diameter scope:f30—f150mm; Temperature range: =30?. Deep well submersible water pump is widely used in various kinds of water conservancy facilities such as farm irrigation, sprinkler irrigation with water, the supply and drainage system of civil building and, industrial and draining water from the hills and mountainous area, the diversion in low-lying areas, water supply and drainage in urban and rural industrial and mining enterprises etc. Deep well submersible water pump spare parts &features: Deep well submersible water pump motor and pump assembled into one. Deep well submersible water pump has simple structure, easy to use and maintenance. Electric motor is three-phase asynchronous motor. Safe and reliable operation, no pollution to water. Installation of deep well submersible water pump 1. 380V voltage deviation is no more than ±5%, frequency is 50HZ, three -phase power deviation is no more than ±1%. 2. Motorcavity must be filled with water to cooling motor and lubricate bearings . 3. The first stage impeller of the pump should be more than 2mm below the moving water surface, pump unit should be less than 70m below the static water level. 4. The distance from the motor bottom to well bottom must be more than 3m. 5. Water temperature should be no more than 20°C. 6. Sand content of the water ( by mass) should be no more than 0.01%. 7. PH value of water 6.5-8.5. 8. Hydrogen sulfide content of the water should be no more than 1.5mg/L. 9. Chloride ion content of the water should be no more than 400mg/L. 10. Water yield of water source should ensure the requirements of pump continuous working.
Submersible pump, motor, pipe, cable.
Supply Ability: 20 units per Month Weight(KG): 420000 kg Condition: New Rated Lifting Moment: 2009kN.m Place of Origin: China Warranty: 1 Year Engine Brand: Imported Hydraulic Pump Brand: Imported Hydraulic Cylinder Brand: Imported Max. Lifting Height: 58.1m Feature: TRUCK CRANE Certification: CE/ISO9001 Warranty of core components: 1 year Brand Name: XCM GIZOOMLION Video outgoing-inspection: Provided Marketing Type: New Product Core Components: Engine Hydraulic valve brand: Imported Application: construction Rated Loading capacity: 50ton Machinery Test Report: Provided Packaging Detail: Export standard packaging
FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
During last decade Guar has immerged as an important industrial raw material and Produced by man for thousands of years. India has been the single largest producer and exporter of Guar gum accounting for more than 80 percent of the global output and trade. Guar has now assumed a larger role among the domesticated plants due to its unique functional properties. India Ranks First in the production of guar which is grown in the North Western part of the Country which mainly includes the states of Rajasthan, Gujarat, Haryana and Punjab. Other main countries are Pakistan, U.S.A and Brazil The by-product of Guar Gum industry consisting of the outer seed coat and germ material is called guar meal. The Guar meal after gum Extraction is a potential source of protein and contains about 42% crude protein which is one and a half times more than the level of protein in guar seed. The protein content in guar meal is well comparable with that of oil cakes. It is used as a feed for livestock including poultry. Guar meal contains two deleterious factors i.e. residual guar gum and trypsin inhibitor, Toasting of Guar Gum improves its nutritive value in chicks. Toasted guar Meal can be used in limited quantity i.e. Up to 10% in Poultry diet. However it can replace groundnut cake by almost 100% in animal feeds. Guar Gum (Galactomanan) is a high molecular weight carbohydrate polymer made up of a large number of mannose and galactose unit linked together. The crude Guar Gum is a greyish white powder 90% of which dissolves in water. It is non ionic polysaccharide based on the milled endosperm of the guar bean whose average. Composition is: Hydrocolloid: 23% Fats: 40% Proteins: 34% The most important property of the Guar is its ability to hydrate rapidly in cold water to attain a very high viscosity at relatively low concentrations. Its specific colloidal nature gives the solution an excellent thickening power which is 6 to10 times thicker than that obtained from starch. It is stable over a wide range of PH and it also improves the flow ability and pump ability of the fluid. It is a superior friction loss reducing agent.
Flow: 10m3/h Head: 21m Power: 7.5kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage.
Shoes, air filter cartridges, oil filter, water filter cartridge, dust collection filter cartridges, dust collection filter bag, liquid filter bag, carbon cartridge ,gas filter, empty glass bottle, empty wine bottle, glass jar, glass bowl, flavoured dry fruit, all type of rice, makhana , leather product, ladies kurti, plazo sets , t shirt, curtain, cotton apron, cushion cover , kitchen towel, garlic powder, ginger powder, onion powder, fresh onion, garlic, ginger, potato, bio fertilizer , door handle , door lock, furniture and sandstone tile, spices, vegetable, coffee powder, frozen pea, frozen sweet corn, frozen mix vegetable, wooden furniture, moringa powder, neem powder, dry fruits, fruits, ready to eat, garments, artificial jewellery, handicraft, shower, ultra slim shower, ro booster pump, adjustable mobile stand, lady bag and wallet, men bag and wallet, portfolio, machine casting, ro booster, sandwich shower, ultra slim shower head, donkey milk and donkey milk powder.
Sonokeling wood itself is a type of hardwood. The weight of rosewood wood is in the range of 0.77 to 0.86. Where from that weight there is approximately 15 percent water content. When viewed from the texture, sonokeling wood has a fairly smooth shape Table of Contents What is Sonokeling Wood Sonokeling Wood Characteristics 1. Black Color 2. Hard Texture 3. Sapwood Can Be Used 4. Anti Termite and Mushroom Attack 5. Berta Resembling Metal Benefits of Sonokeling Wood Examples of Objects from Sonokeling Wood 1. Furniture 2. Musical Instruments 3. Accessories 4. Tableware Book Recommendations 1. Unique Lamp Creations from Unused Materials 2. 3D Room Drawing Series: 22 Multifunctional Furniture Designs 3. Various Inspirations for Simple Minimalist Furniture Arrangements 4. Designing and Assembling Wooden Furniture: Etb
1. Fruit and vegetable cleaning production line: material lifting -- selection and sorting -- first cleaning -- second cleaning -- draining water -- air drying 2. Leaf vegetables Processing flow: selection and sorting - material cutting - material lifting - first cleaning - second cleaning - drainage water- air drying 3. Processing flow of root vegetables: peeling and cleaning - selection and sorting - material lifting - material cutting - material lifting - first cleaning - second cleaning - draining - dehydration
The curved edges on this serving plate help to avoid sliding food or spilling liquids and also make it easier to lift and carry around. This ensures that none of your favorite dishes will fall during the preparation for your occasion. . After using simply a wipe-clean food tray with some soapy water. We supply the best quality products on the market. Our customers are first on our priority list and we simply provide you with the best product and service