Removable Plate Heat Exchanger: The Removable plate heat exchanger is a new type of high-efficiency heat exchanger composed of a series of metal sheets with a certain corrugated shape. Thin rectangular channels are formed between the various plates, and heat is exchanged through the halves. Plate heat exchanger is an ideal equipment for liquid-liquid and liquid-vapor heat exchange. Under the same pressure loss, the heat transfer coefficient is 3-5 times higher than that of the tubular heat exchanger, the floor area is one third of that of the tubular heat exchanger, and the heat recovery rate can be as high as 90% or more. This product is suitable for chemical, machinery, food, beverage, medicine, residential heating, hot water supply, air conditioning and other departments. Intermediate heat exchangers used in conjunction with boilers, intermediate heat exchangers in high-rise buildings, etc., soda ash industry, synthetic ammonia, alcohol fermentation, resin synthesis cooling, etc. Detachable plate heat exchanger is a new type of energy-saving heat exchange device with high heat transfer effect, compact structure, small footprint, easy operation, convenient cleaning, disassembly and maintenance, and easy to change the heat exchange area or process combination, etc. advantage. 1. The Removable plate heat exchanger has a compact structure with a small footprint, and the heat exchange area per unit volume is 2 to 5 times that of the shell-and-tube type. Unlike the shell-and-tube type, the maintenance site for drawing out the tube bundle is not reserved, so the same For heat exchange, the plate heat exchanger covers an area of â??â??about 1/5~1/8 of the shell and tube heat exchanger. 2. It is easy to change the heat exchange area or process combination. As long as a few plates are added or reduced, the purpose of increasing or reducing the heat exchange area can be achieved; by changing the plate arrangement or replacing a few plates, the required process combination can be achieved. It is almost impossible to increase the heat transfer area of â??â??shell and tube heat exchangers to adapt to new heat exchange conditions. Removable plate heat exchanger is a kind of heat exchanger that is widely used in heat exchangers. It is widely used in chemical, machinery, food, beverage, medicine and other occasions. Users should select and use according to actual needs and the advantages and characteristics of heat exchangers are used to choose, and well-known brand products are also very important.
Industrial equipment Brazed plate heat exchanger is a new type of high-efficiency heat exchanger made of a series of metal sheets with a certain corrugated shape stacked and brazed. Thin rectangular channels are formed between various plates, and heat is exchanged through the plates. Compared with the conventional shell and tube heat exchanger, its heat transfer coefficient is much higher under the same flow resistance and pump power consumption, and it has a tendency to replace the shell and tube heat exchanger within the applicable range. Applications: Refrigeration: used as condenser and evaporator b. HVAC: intermediate heat exchangers used in conjunction with boilers, intermediate heat exchangers in high-rise buildings, etc. c. Chemical industry: soda ash industry, ammonia synthesis, alcohol fermentation, resin synthesis cooling, etc. d. Metallurgical industry: heating or cooling of aluminate mother liquor, cooling of steelmaking process, etc. e. Machinery industry: cooling of various quenching fluids, cooling of reducer lubricating oil, etc. Design Parameters Flow range: 1-2000 m3/h Working pressure: vacuum-8.2MPa Operating temperature: -195-538C Interface size: 1"-DN300 welding, flange, thread and other connection forms Corrosion resistance: Welding seal without rubber gasket, choice of various metal and alloy materials, super corrosion resistance, longer service life. Application field: Crude oil, natural gas purification and chemical products; chemical industry; pharmaceutical and specific chemicals; injection control systems; HVAC, district heating, thermal power plants; food processing; cooling tower heat recovery Process requirements Pickling temperature: Raising the pickling temperature is conducive to improving the descaling effect. If the temperature is too high, it will aggravate the corrosion of the pickling solution to the heat exchanger plates. Through repeated tests, it is found that the pickling temperature should be controlled at 60. 2) Concentration of pickling solution: According to repeated tests, the pickling solution should be prepared according to the concentration of formic acid 81.0%, water 17.0%, buffer 1.2%, and surfactant 0.8%, and the cleaning effect is excellent. 3) Pickling method and time: The pickling method should be carried out by a combination of static soaking and dynamic circulation. The pickling time is static soaking for 2h first, and then dynamic circulation for 3~4h. During the pickling process, samples should be taken frequently to test the pickling concentration. When the difference between the two adjacent test concentrations is less than 0.2%, the pickling reaction can be considered to be over. 4) Passivation treatment: After pickling, most of the scale and metal oxides on the surface of the plate heat exchanger will be dissolved and fallen off, exposing new metal, which is very easy to corrode. The sheet is passivated.
The melting point of WJWAX's food grade paraffin wax NO.58 is about 58-60. This product is widely used in gum based production of chewing gum and Bubble gum in China. It is also a very popular food grade paraffin product abroad. We are a direct distributor of Kunlun and Sinopec, offering highly competitive prices. Paraffin wax is a white or colorless soft solid that's used in a variety of applications due to its chemical stability, large molecular weight, and low reactivity. It's a byproduct of the oil refining process, and its properties can be fine-tuned by controlling the refining process. Paraffin wax with a melting point of 58-60â?? is often used in the food industry, particularly in the production of gum base, the non-nutritive, non-digestible, water-insoluble base used to carry sweeteners, flavors, and colors in chewing gum and bubble gum. Product Application Melting Point: Paraffin wax No.58-60â?? has a melting point in the range of 58 to 60 degrees Celsius. This property makes it ideal for use in the gum base, as it will not melt easily in the mouth during chewing. Tasteless and Odorless: This type of paraffin wax is both tasteless and odorless. Therefore, it does not interfere with the flavors added to the chewing gum. Safe for Consumption: Food-grade paraffin wax is deemed safe for consumption, ensuring it doesn't pose any health risks when used in gum bases. Viscosity: Paraffin wax has a low viscosity which contributes to the smooth texture of the chewing gum. Insoluble in Water: The wax is insoluble in water, which helps to keep the gum from dissolving while it's being chewed. Uses in Gum Base In a gum base, food-grade paraffin wax serves several purposes: Texture and Chewability: The wax helps to provide the gum with its characteristic elasticity and chewiness. Stability: It aids in maintaining the stability of the gum, preventing it from breaking down or dissolving during chewing. Flavor Retention: Paraffin wax helps to encapsulate and retain the flavoring agents in the gum, releasing them over time as the gum is chewed. Shelf Life: It also contributes to the long shelf life of gum products by serving as a moisture barrier. Paraffin wax No.58-60â?? is just one of several ingredients in a typical gum base. Others may include elastomers, resins, plasticizers, antioxidants, and fillers. All these ingredients are carefully chosen and combined to achieve the desired characteristics of the final gum product. Conclusion Food-grade paraffin wax No.58-60â?? is a crucial ingredient in the production of gum base. Its unique properties contribute to the texture, stability, flavor retention, and shelf life of chewing gum. The safety of this type of paraffin wax for consumption makes it a reliable choice for use in food-grade applications.
Brief Introductions: Type: 6A2 Bond: Vitrified Application: PCD, PCBN, CVD, CNC tools grinding Specification: Customized Packages: Hard carton Delivery Time: 15 workdays by express Introductions of Moresuperhard s 6A2 10000# Vitrified Grinding wheel Model D (mm) T (mm) H (mm) W (mm) X (mm) 6A2 PCD Tool Grinding 150 40 32 40 5 10 15 20 10 125 40 32 40 5 10 15 20 10 100 40 20 32 40 3 5 10 15 20 10 Grain Size Machining Type Application W40(500# D35) W28(D20) Rough Regrinding a blade edge profile and sharpening of much worn inserts W20 (800# -1000#, D20) Universal Standard grain size also can get a high sharpening efficiency, good quality surfaces W10 (1500# D15A) W7 (2000# D15B) Finish Finishing grinding - getting a very good quality of machined surfaces W5 (3000# D7) W3.5 (4000# D3) Super Finish Super finish grinding - getting a brilliant quality of machined surfaces W1.5 (10000# D1) Finest Finish Finest finish grinding getting a perfect quality of machined surfaces Others grits can be made according to customers' requirements. Advantages of Moresuperhard s 6A2 10000# Vitrified Grinding wheel The porous structure of the abrasive improved diamond exposure and can prevent vertical streaks on workpiece and improve surface quality Accurately control geometric tolerances to make a good abrasive layer Good self-sharpening, high grinding efficiency, high wear resistance and less abrasive grain consumption Super High precision workpiece. PCD tools can reach high efficiency, good surface finish and edge no chipping Vitrified bond wheels offer tool life greater than 150 times that of a resin bond wheel and can be easily trued and dressed on the machine Service: Detailed Specifications can be customized! Provide after-sales service. Technical support on usage. Return and exchange of products for non-human reasons. a professional manufacturer of grinding, cutting, polishing and dressing tools. Thanks to abundant experience in surface treatment, we design and offer a complete grinding and dressing solution to our customers in various industries. With innovative and creative development conception, is tirelessly striving to provide excellent design, superior quality and perfect service to world-wide customers. More than 1000+ customers benefit from our professional technical services.
As a new type of green energy, hydrogen energy is a new type of green energy, and its sustainable manufacturing has become the goal of the industry. Water electrolysis hydrogen production, hydrogen generators, etc., hydrogen energy equipment emerge in endlessly, and relatively safe and efficient hydrogen production consumables have become a relative key. Product parameters Brand: TOPTITECH Material: Gr1 Shape: Rectangular Applicable object: electrolyzer Thickness: 0.8-2.0mm Specifications: can be customized Mesh: 1000 mesh/inch Filtration accuracy: 20 microns Type: Efficient Performance: acid resistance; alkali resistance; high temperature resistance Uses: water, gas, liquid Features 1. Precise air permeability, uniform air holes, certain mechanical strength, high adaptability for external processing; 2. High-purity raw materials, resistant to various acid and alkali environments, a corrosion-resistant material; 3. The porosity can reach 35%, which is a relatively high-strength product in a breathable material and can bear pressure; 4. It can withstand a certain temperature, for example, it can be used normally in a long-term heating environment within 300 degrees. Applications 1. Decarbonization filtration in the concentrated preparation link of the pharmaceutical industry and security filtration before terminal filtration in the thin preparation link. 2. Filtration, decarbonization filtration, and fine filtering of materials used in the manufacturing of raw materials. 3. Filtration following ozone sterilizing and ozone aeration, as well as security filtration for water treatment industries RO, EDI, and ultrafiltration systems. the 4. Clarify and filtering of alcohol, beer, soy sauce, vegetable oil, mineral water, and other drinks and food. 5. Material purification and sintered porous titanium plate at the feed inlet, decarbonization filtration and precision filtration of liquid products, liquid raw materials, and pharmaceutical intermediates in the chemical industry, filtration and recovery of ultra-fine fine bodies and catalysts, precision filtration and system heat conduction after resin adsorption Impurity removal and filtration of oil and materials, catalytic gas purification, etc. the 6. Before reverse osmosis in the seawater desalination field, oilfield return water filtering and security filtration. 7. White clay filtration and high-temperature decarbonization in the dye business. 8. Steam, compressed air, and catalytic gas purification and filtration are the primary aspects of gas purification. Process The pure titanium powder is pressed into a plate shape, and then sintered in a high-temperature vacuum sintering furnace. The particles are naturally bonded to form a plate shape, and then cooled to form a plate base material, which can then be cut into the desired shape.
Titanium rod filter element is a porous filter element made of industrial high-purity titanium, which is formed by sieving, cooling and isostatic pressing, and then sintered at high temperature and high vacuum. It has outstanding qualities such as corrosion resistance, high temperature resistance, high strength, ease of filtration accuracy assurance, and ease of regeneration. It is suitable for the filtration of various corrosive media, such as: hydrochloric acid, sulfuric acid, hydroxide, sea water, aqua regia, and chloride solutions such as iron, copper, and sodium. Technical Parameters Filtration accuracy: 0.22um-100um Porosity: 30-40% Air permeability: 0.02-20M3cm/m2h Compressive strength: 0.5-1.5Mpa Temperature resistance: 280C (wet state) Maximum working pressure difference: 0.6Mpa Diameter: 30mm 50mm 60mm Length: 5 inches 10 inches 20 inches 30 inches 40 inches Interface form: M20 M30 222 226 DFPD (double flat port) Filtration accuracy: 0.45m, 1m, 3m, 5m, 10m, 20m, 30m, 50m, 80m, 100m Features 1. High temperature resistance Generally, it can be used normally under 280 degrees. 2. Uniform and stable precision Uniform structure, narrow pore size distribution, high separation efficiency, high porosity, low filtration resistance, high penetration efficiency. 3. Resistance to corrosion Chemical stability, acid and alkali corrosion resistance, and oxidation resistance are all strengths. 4.A large filter area In accordance with food hygiene and pharmaceutical GHP criteria, there is no particle shedding and no secondary polluting of the original solution. 5. Longevity It is easy to clean, can be regenerated online, and has a long service life (generally several times that of membrane filter elements). Applications 1. It is employed in the pharmaceutical business for decarbonization filtration in the concentrated preparation of big infusions, tiny injections, eye drops, and oral liquids, as well as security filtration prior to terminal filtration in diluted preparations. 2. Impurity removal and filtration in the raw material production process, decarbonization filtration, and fine filtration of materials. 3. Ultrafiltration, RO, and EDI security filtration in the water treatment business, as well as filtration following ozone sterilization and ozone aeration. 4. Clarification and filtering of beverages, liquor, beer, vegetable oil, mineral water, soy sauce, and vinegar. 5. Filtration and recovery of ultrafine fine particles and catalysts, precision filtration following resin adsorption, and impurity removal and filtration of system heat transfer oil and materials, catalysis Gas rest purification, etc. are all processes used in the chemical industry to decarbonize liquid products, liquid raw materials, and pharmaceutical intermediates.
The stainless steel wedged wire mesh filter uses metal wedge wire mesh as the filter element, which has the advantages of high mechanical strength, high pressure difference resistance, and easy flushing and regeneration; the nearly two-dimensional filter has no dead spots for particle accumulation, and the wedge-shaped gaps can be gathered during backwashing. Backwashing energy, backwashing effect is good. The stainless steel wedged wire mesh filter element is easy to leak, wear-resistant and corrosion-resistant. The mesh has a trapezoidal cross section, and the gap is large at the bottom and narrow at the top. The whole wedge mesh is welded by wedge wire and supporting structure. There is an appropriate line spacing between the wedge wires arranged in parallel, which determines the filtration area. Product Parameters Brand: TOPTITECH Material: SS304, SS316L Filtration accuracy: 25um-800um Operating pressure: 5Mpa Shape: Flat, Cylindrical Features 1.Strong mechanical construction, able to tolerate significant pressure variations; 2.The filter gap is consistent, allowing for the formation of a fairly homogenous filter cake that is helpful for backwash regeneration; 3. Strong backwash regeneration ability; 4. Pressure-resistant, temperature-resistant, corrosion-resistant, applicable to various fluids. Applications Stainless steel wedged wire mesh filter elements are widely used in drinking water treatment, building circulating water treatment, industrial circulating water treatment, sewage treatment, mining industry water treatment, golf course water treatment, construction, steel, petroleum, chemical industry, electronics, power generation, textile, paper making , food, sugar, pharmaceuticals, plastics, automotive industries and other fields. 1.The petrochemical industry, which uses catalytic reaction, hydrodesulfurization, styrene dehydrogenation, ammonia conversion, isomerization, and other up-down and radial flow processes; 2. Sewage treatment and flood system: water inlet, basement supply, carbon and resin retention, demineralization method softening and ion exchange, sand, dual and mixed media filtration, wastewater sludge treatment; 3. screening, coal drying, starch filtration, pulp and plant fiber filtration, and beverage filtration are all involved in the processing of minerals, paper, and food;
Pocket filters, also referred to as bag filters,pocket filters are constructed of a plastic or galvanized steel frame and contain fiberglass or synthetic media. They are called pocket filters because the media is stitched or sonically welded to form pockets ranging from 10 to 36 inches deep. Bag / Pocket Air Filters are constructed with galvanized steel frames and sections of synthetic non-woven fabric media to create pockets. The bag's flexible stitching helps to maintain the media's shape in a variety of airflow circumstances. The stitching is sealed with thermoplastic resin to stop any leaks. There can be a specific number of bags in each bag-type air filter, such as a 6 pocket bag filter or an 8 pocket bag filter. They can be modified to meet the requirements of the real application. SNYLI bag filters provide high-efficiency filtration while keeping low-pressure drop against airflow. We have efficiency range from 40-45% (orange), 60-65% (green), 80-85% (pink), and 90-95% (yellow). The frame is made of 26-gauge galvanized steel. Different kinds of gasket are available to meet your application purpose. Cleaning Instructions 1. Remove any apparent dry debris from the pockets with caution. You can either shake out any loose particles by hand or by setting the filter (pockets-up) over a big garbage can and lightly smacking the outside of the pockets with your hand. 2. Spray water through the exterior of the pockets with a low-pressure faucet or garden hose so that it drains into the middle and out of the pockets at the frame opening. Repeat until it's clean. 3. Allow the filter to completely drain of all water. The filter shouldn't be put back in until it is totally dry. 4. Detergent is not needed. Applications Heavy and metal industry Chemical plants Pharmaceutical and food industry Gas trubo and Co-generation utility plants Paint spray plants Pre-filtration and recycling or exhaust air FAQ Q1. Can the products be customized? A: Yes, both the products and the packaging can be in customized. Q2. What is your terms of payment? A: We accept the western union/Money Gram/ T/T,L/C; Q3. Do you test all your goods before loading? A: Yes, we have 100% rigorous test before delivery.
Product Description It can be used in many aspects, especially in various flat forming conversions of thermoplastics, such as PP, HDPE, and LDPE etc. It is mainly used for woven bag, jumbo bag, the sun-shade net etc. This line has the performance of high speed, high production, low energy consumption, good forming quality of the bobbin. The structure of this line is compact with a pleasing appearance,smooth running, flexible and reliable control excellent manufacturing technics, convenient and safe operation. Features of Machine: Most experienced manufacturer: Professional machine and mature technology with more than 20 years experience. Green and economic: 100% recycled PET water bottle flakes or recycled PP resin as raw material to make qualified plastic filament yarn for various usage such as cleaning broom, brush, and packing rope. Machine Development: Continuous improvement and feedback from customers from more than fifty countries all around the world. Better performance: low energy consumption, high production capability Easy Operation: Automatic and convenient operation with one worker Technical Parameters Model TPM-65 TPM-80 TPM-90 Die width 600mm 800mm 1000mm Screw diameter 65mm 80mm 90mm Stretch Ratio 1:8 1:8 1:8 Size 24 32.5m 263 2.5m 28 32.5m Total power 60KW 80KW 100KW weight 3T 3.5T 4T Machine list No Description Quantity 1 Dehumidifying and Crystallizing Equipment 1 set 2 SJ-75/33 Single Screw Extruder 1 set 3 Automatic Screen Changer 1 set 4 Mold 1 set 5 Water Tank Cooling System 1 set 6 The first seven haul off machine 1 set 7 Water heating oven 1 set 8 the secend seven haul off machine 1 set 9 Glazing machine 1 set 10 Air oven 1 set 11 the third seven rollers haul off machine 1 set 12 winding machine 1 set 13 shaping machine 1 set 14 cutting machine 1 set 15 packaing machine 1 se
The smallest and most compact lab water system from tap to ultrapure water, integrating pretreatment, RO, DI, UV, UF and terminal filter into one. Whole case with one time injection molding process, material: polypropylene, avoid rusting and keep clean, to meet GLP standard. Top cap of pretreatment in the case can be rapidly opened to replace the cartridges without opening the case. System automatically works, with electronic pressure sensor and microcomputer controlling. Automatic stop without water, automatic stop when water tank full, automatically cutting off water when pump stopping, guaranteeing 24 hours work. Auto self-flushing of RO membrane function, extend RO membranes life. On-line resistivity monitor, with apheliotropic LCD display, to detect the quality of deionized or ultrapure water. Attached portable TDS (total dissolved solid)/conductivity test pen, with dry cell design, to detect the quality of feed water and RO water. External water tanks is optional to meet different need and assure ample water-supply. Tube and adapter with NSF authorization and top quality, reduce TOC level and assure ultrapure waters quality. Long life pretreatment (including PP fiber, and active carbon cartridge), effectively protect RO membrane. RO module with DOW membrane, ensure long life, stable operation and high desalinization rate. 4 independent ultrapure cartridges with DOW top polishing resin, ensure ultrapure waters quality up to 18.2 M.cm, with the lowest TOC level and running cost. Double wavelength (185&254nm) ultraviolet lamp module, restrain bacterias increase and reduce TOC. MWCO 5000D ultrafiltration module, effectively eliminate endotoxin, and suitable for precise cell cultivating and IVF. (0.45+0.1)um double layer PES terminal disinfection filter, assure that terminal pure water is absolutely axenic. Commodity Basic Eliminating endotoxin Low TOC Synthesizing Model 15 l/h Smart-S15 Smart-S15UF Smart-S15UV Smart-S15UVF 30 l/h Smart-S30 Smart-S30UF Smart-S30UV Smart-S30UVF Feed water* Tap water: TDS200ppm) System process** PF+AC+RO+DI+TF PF+AC+RO+DI+UF+TF PF+AC+RO+UV+DI+TF PF+AC+RO+UV+DI+UF+TF Specifications of UP water UP Resistivity 18.2M�©.cm@25â?? Heavy metal ion < 0.1 ppb TOC)***
Features of Dwell s EPE(EVA/POE/EVA) solar film extrusion line: Film Layers structure: According to the finished film, EVA/POE/EVA film has three layers(EPE film). It will be based on the customer requirements, EPE solar film extrusion line can also produce EVA or POE single layer. China EVA / POE / EPE solar film is used for solar cell encapsulation. After lamination and curing, it is bonded and sealed. It plays the role of high light transmittance, preventing water vapor penetration, high and low-temperature resistance, and ultraviolet light resistance to ensure the stable and efficient use of battery modules. It is a durable and reliable packaging material. The EVA / POE / EPE packaging film extrusion line of Dwell machinery is in a leading position in the world. Advantages of the Dwell EPE(EVA/POE/EVA) solar film extrusion line If producing EPE film, the line speed of the EPE solar film extrusion line can reach 12m/min-15m/min, if EVA, can reach15-18m/min, and if POE, can reach 10-13m/min. Cooling parts to ensure shrinkage rate is less than 3%. DWELL special winder to ensure micro-tension, and achieve automatic winding and cutting. Comparison of the Dwell EPE(EVA/POE/EVA) solar film and EVA solar film and POE solar film 1.Transparent EVA solar film: with high light transmittance, it is used for bonding glass and cells; The raw materials are EVA resin and various modifiers, which are cheaper. 2.White EVA solar film: compared with transparent EVA solar film, the pretreatment of white fillers such as titanium dioxide is added. It has a strong barrier, low light transmittance, and high reflectivity, which can improve the power generation of components. It has strong resistance to damp-heat aging and ultraviolet aging and can inhibit the aging and cracking of the back sheet. 3.Poe solar film: Poe solar film has a higher water vapor barrier rate and stronger anti-PID performance so the module can be used for a long time. It is the main packaging adhesive film of a double-sided double glass module and film module at present. 4.EPE(EVA/POE/EVA)solar film: It has both the anti-PID performance of POE and lamination efficiency of EVA solar film and reduces the use of POE particles to achieve cost reduction and efficiency increase. At present, it is mainly used in high-efficiency components.
Power transformer Transformer working for medium frequency induction furnace, electric arc furnace, continuous casting machine, rolling mill steel plant. 220kV, 110kV and 66kV low loss series transformers; products with reliable performance, low partial discharge, low loss, low noise, high reliability, and strong resistance to sudden short circuit, its excellent performance has won the majority of users and related Experts highly praise. Partial discharge: at 1.5 times the rated voltage, the apparent discharge of the product is less than 80pC; Noise: Product noise of 63MVA and below is below 58dB (AN); Loss: No-load loss is about 30% lower than the IEC standard; Reliability: All in-service products have no damage accidents and oil leakage; Short-circuit resistance: SFZ11-50000 / 132 has passed the short-term ability test of the Netherlands KEMA and the National Transformer Quality Supervision and Inspection Center laboratory. Passed CE, UL, CSA, ROSH certification Coil: A All coils are made of 100% oxygen-free copper, and high-voltage coils are tangled. Continuous structure, in order to improve the distribution characteristics under impulse voltage, to obtain a more uniform electric field distribution, the bracing pads are rounded to improve the high reliability of insulation. A Iron core: The core material is high-quality cold-rolled silicon steel sheet with high magnetic grain orientation, and adopts advanced German Georg automatic shearing line to control the burr of the cutting mouth to be less than 0.02 mm. The silicon steel sheet adopts the technology of not stacking the iron yoke. The joint of the silicon steel sheet is a 45 �° full oblique stepped joint. After the iron chip is stacked, the overall pressure and epoxy glue are used to make the iron core three-pillar two yoke become a strong , Flat, high vertical accuracy, effectively improve the no-load performance, while reducing noise. Between the iron core column and the inner coil, the iron core column is supported by a brace plate, the iron yoke is tensioned by a glass ribbon impregnated with epoxy resin, and the lower iron yoke and the lower fuel tank are topped by a back pressure nail bolt. In addition, the upper iron yoke and the upper fuel tank are fixed in three places, so the body can withstand the bumps during transportation without displacement in the fuel tank.
Mask Melt-blown Cloth Spinneret Die Mould 1. overview and principle of meltblown cloth equipment the melt-blown method is a method for preparing fibers by blowing polymer melts with high-temperature and high-speed airflow to rapidly draw them. (melt-blown cloth extruder, melt-blown cloth equipment, melt-blown cloth production line) after the polymer chips are heated and pressed into a molten state by a screw extruder, they reach the spinneret hole at the front end of the nozzle through the melt distribution flow path, and after extrusion, they are refined by two converging high-speed and high-temperature air flows to refine . the refined fibers are cooled and solidified on the screen device to form a melt-blown nonwoven fabric. 2. components of meltblown cloth equipment meltblown heads, automatic charging system equipment components, ultrasonic cleaning machines, air heaters, centrifugal fans, screw extruders, meltblown web forming machines, meltblown offline winding machines, meltblown offline slitting machines and other key equipment. 3. the core components of meltblown cloth equipment spinneret the spinneret for melt spinning is a representative spinneret for the manufacture of synthetic fibers such as polyester and nylon. the thermoplastic resin is heated and melted, extruded through the spinneret in air or water at a certain speed, and cooled spinning method of solidifying into fibers the most core technology is the small nozzle on the spinneret. this nozzle not only has a small size of only 0.15mm, but also needs to process a complex hole pattern on such a small nozzle. the processing is extremely difficult, and the nozzle processing process requires months. if the processing accuracy is not high, the melt-blown cloth finally produced will not meet the corresponding technical requirements, which will affect the protective performance of the mask. structure of melt-blown cloth spinneret according to the shape of the spinneret, the structure of the spinneret can be divided into three forms: round, sector and rectangle. at present, round and rectangular plates are mostly used at home and abroad. to suit different chemical fiber spinning occasions, the round spinneret is divided into flat type, flange flat type, flat ring, flange ring, etc .: the rectangular spinneret is divided into flange rectangle and flange groove rectangle, etc. , mostly used for spinning short fibers with many holes. meltblown cloth spinneret structure
Depressed centre discs Depressed center metal grinding disc in 4inch diameter for agressive grinding action and smooth running wheels. The amount of removed metal is reduced, increasing cutting speed and reducing the heat generated. Ideal for professional use 4 inch grinding wheel Depressed centre discs Depressed center metal grinding disc in 4inch diameter for agressive grinding action and smooth running wheels. The amount of removed metal is reduced, increasing cutting speed and reducing the heat generated. Ideal for professional use Features 1) High-quality white aluminum grains 2) Excellent durability and sharpness with less down time 3) For all types of metal material cutting 4) High security Assured with MPA, EN12413 and OSA standard 5) Reinforced double Fiberglass mesh, front and back Key Specifications: Sintered mesh filter discs is made of SS multi-layer sintered wire mesh through laser-cutting Mainly used in explosion-proof components, noise components, pressure, and flow meter and other precision instrument components Materials: SS304, SS316, SS316L Note: can be made according to customer requirements for edging, adding outer rings. It can be processed into circular, fan-shaped, square, and other special shapes according to customer's requirements We're established in2018yr, Yongkang Nova Hardware Co., Ltd. is a manufacturer trader specialized in the research,development and production Cutting Wheel.We are located in Yongkang City ,Zhejiang Province,with convenient transportation access. All of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world. If you are interested in any of our products or would like to discuss a custom order for wholesaler or retailer. please feel free to contact us. We are looking forward to forming successful business relationships with new clients around the world in the near future. our products including: cutting disc,cutting wheel,grinding wheel,flap wheel,abrasive wheel,etc. Abrasive Type A- Aluminum oxide ZA-Zirconium aluminum grain/ Aluminum oxide C-Silicon Carbide AC-Aluminum oxide/Silicon Carbide Z-Zirconium aluminum grain WA-White aluminum oxide Grit Size 16-24 coarse Structure 0-3 tight 30-60 medium 4-7 medium 70-220 fine 8-14 open Bond BF-Phenolic resin Hardness D-L soft M-N medium P-S hard T-Y very hard
3D CNC Router Wood Carving Machine3D CNC Router Wood Carving Machine1.Technical ParametersModelSD1325a)Control System Richauto DSP Handleb)Work Table Vacuum table with 5.5kw Vacuum Pumpc)Table Structure 8mm Steel Pipe Weldedd)Spindle 4.5KW Water Cooling Spindlee)Switch Vacuum Switchf)Motor/Driver Leadshine Stepper Motor(Servo Motor For optional)g)Rail 25mm PMI Square RailEfficient working area1300mm*2500mm*200mmMax carving speed15000mm/minTransmission typeX,Website:http://www.cncsudiao.com,Y Gear Rack, Z Ball screwInverterSunfar Inverter/Delta InverterSupport file formatPLT , BMP , DXF , AL etcPower supplyAC380V/ 50HzHow to Use Design on the software,Then output.(Artcam,Ucancam,Type3)Input the file to control system by USB.(Syntec Control)Put the material on vacuum table,Move the Spindle to start point ,Then Click "Start".After a while,your product Finish.Main applications of cnc router : 1.Furniture industry: wooden doors, cabinet doors, board, office, solid wood furniture 2.Other wood products industry: speakers, game consoles cabinets, computer tables, sewing machine table, musical instruments, etc. 3.Board processing industry: insulation piece, plastic chemical products; PCB; fast train inside body, bowling tracks, stairs; compact grade laminate, epoxy resin, ABS, PP, PE and other cementitious mixturesâ??s milling process 4..Decoration industry: folding screen, wave plates, large wall, advertising boards, signs and logoâ??s processing.3.Features of MachineImported main parts for the machine,famous brand,stable personality.Dust cover for Z axis,Y guid and rack in the same side.Vacuum table have strong adsorbability,can adsorb different size materials.High speed and effciency,the engraving speed can reach to 20m/min,large cutting power not only to elaboratory carved a jagged,also smooth clear bottom.There is also any other size for a choice.Compamy Information14 years machine manufacture7 years export experience3 factories200 workersCE ISO CertificationBeijing Exhibition, Shanghai Exhibition5.After-sale Service6.FAQ I hope we can discussed online by whatsapp/wechat/Skype,To introduce more detail and answer your question.And we are seeking worldwide distributors.I believe Win-win is the best way for us.
3D CNC Router Wood Carving Machine3D CNC Router Wood Carving Machine1.Technical ParametersModelSD1325a)Control System Richauto DSP Handleb)Work Table Vacuum table with 5.5kw Vacuum Pumpc)Table Structure 8mm Steel Pipe Weldedd)Spindle 4.5KW Water Cooling Spindlee)Switch Vacuum Switchf)Motor/Driver Leadshine Stepper Motor(Servo Motor For optional)g)Rail 25mm PMI Square RailEfficient working area1300mm*2500mm*200mmMax carving speed15000mm/minTransmission typeX,Y Gear Rack, Z Ball screwInverterSunfar Inverter/Delta InverterSupport file formatPLT , BMP , DXF , AL etcPower supplyAC380V/ 50HzHow to Use Design on the software,Then output.(Artcam,Ucancam,Type3)Input the file to control system by USB.(Syntec Control)Put the material on vacuum table,Move the Spindle to start point ,Then Click "Start".After a while,your product Finish.Main applications of cnc router : 1.Furniture industry: wooden doors, cabinet doors, board, office, solid wood furniture 2.Other wood products industry: speakers, game consoles cabinets, computer tables, sewing machine table, musical instruments, etc. 3.Board processing industry: insulation piece, plastic chemical products; PCB; fast train inside body, bowling tracks, stairs; compact grade laminate, epoxy resin, ABS, PP, PE and other cementitious mixturesâ??s milling process 4..Decoration industry: folding screen, wave plates, large wall, advertising boards, signs and logoâ??s processing.3.Features of MachineImported main parts for the machine,famous brand,stable personality.Dust cover for Z axis,Y guid and rack in the same side.Vacuum table have strong adsorbability,can adsorb different size materials.High speed and effciency,the engraving speed can reach to 20m/min,large cutting power not only to elaboratory carved a jagged,also smooth clear bottom.There is also any other size for a choice.Compamy Information14 years machine manufacture7 years export experience3 factories200 workersCE ISO CertificationBeijing Exhibition, Shanghai Exhibition5.After-sale Service6.FAQ I hope we can discussed online by whatsapp/wechat/Skype,To introduce more detail and answer your question.And we are seeking worldwide distributors.I believe Win-win is the best way for us.
3D CNC Router Wood Carving Machine3D CNC Router Wood Carving Machine1.Technical ParametersModelSD1325a)Control System Richauto DSP Handleb)Work Table Vacuum table with 5.5kw Vacuum Pumpc)Table Structure 8mm Steel Pipe Weldedd)Spindle 4.5KW Water Cooling Spindlee)Switch Vacuum Switchf)Motor/Driver Leadshine Stepper Motor(Servo Motor For optional)g)Rail 25mm PMI Square RailEfficient working area1300mm*2500mm*200mmMax carving speed15000mm/minTransmission typeX,Website:http://www.cncsudiao.com,Y Gear Rack, Z Ball screwInverterSunfar Inverter/Delta InverterSupport file formatPLT , BMP , DXF , AL etcPower supplyAC380V/ 50HzHow to Use Design on the software,Then output.(Artcam,Ucancam,Type3)Input the file to control system by USB.(Syntec Control)Put the material on vacuum table,Move the Spindle to start point ,Then Click "Start".After a while,your product Finish.Main applications of cnc router : 1.Furniture industry: wooden doors, cabinet doors, board, office, solid wood furniture 2.Other wood products industry: speakers, game consoles cabinets, computer tables, sewing machine table, musical instruments, etc. 3.Board processing industry: insulation piece, plastic chemical products; PCB; fast train inside body, bowling tracks, stairs; compact grade laminate, epoxy resin, ABS, PP, PE and other cementitious mixturesâ??s milling process 4..Decoration industry: folding screen, wave plates, large wall, advertising boards, signs and logoâ??s processing.3.Features of MachineImported main parts for the machine,famous brand,stable personality.Dust cover for Z axis,Y guid and rack in the same side.Vacuum table have strong adsorbability,can adsorb different size materials.High speed and effciency,the engraving speed can reach to 20m/min,large cutting power not only to elaboratory carved a jagged,also smooth clear bottom.There is also any other size for a choice.Compamy Information14 years machine manufacture7 years export experience3 factories200 workersCE ISO CertificationBeijing Exhibition, Shanghai Exhibition5.After-sale Service6.FAQ I hope we can discussed online by whatsapp/wechat/Skype,To introduce more detail and answer your question.And we are seeking worldwide distributors.I believe Win-win is the best way for us.
3D CNC Router Wood Carving Machine3D CNC Router Wood Carving Machine1.Technical ParametersModelSD1325a)Control System Richauto DSP Handleb)Work Table Vacuum table with 5.5kw Vacuum Pumpc)Table Structure 8mm Steel Pipe Weldedd)Spindle 4.5KW Water Cooling Spindlee)Switch Vacuum Switchf)Motor/Driver Leadshine Stepper Motor(Servo Motor For optional)g)Rail 25mm PMI Square RailEfficient working area1300mm*2500mm*200mmMax carving speed15000mm/minTransmission typeX,Y Gear Rack, Z Ball screwInverterSunfar Inverter/Delta InverterSupport file formatPLT , BMP , DXF , AL etcPower supplyAC380V/ 50HzHow to Use Design on the software,Then output.(Artcam,Ucancam,Type3)Input the file to control system by USB.(Syntec Control)Put the material on vacuum table,Move the Spindle to start point ,Then Click "Start".After a while,your product Finish.Main applications of cnc router : 1.Furniture industry: wooden doors, cabinet doors, board, office, solid wood furniture 2.Other wood products industry: speakers, game consoles cabinets, computer tables, sewing machine table, musical instruments, etc. 3.Board processing industry: insulation piece, plastic chemical products; PCB; fast train inside body, bowling tracks, stairs; compact grade laminate, epoxy resin, ABS, PP, PE and other cementitious mixturesâ??s milling process 4..Decoration industry: folding screen, wave plates, large wall, advertising boards, signs and logoâ??s processing.3.Features of MachineImported main parts for the machine,famous brand,stable personality.Dust cover for Z axis,Y guid and rack in the same side.Vacuum table have strong adsorbability,can adsorb different size materials.High speed and effciency,the engraving speed can reach to 20m/min,large cutting power not only to elaboratory carved a jagged,also smooth clear bottom.There is also any other size for a choice.Compamy Information14 years machine manufacture7 years export experience3 factories200 workersCE ISO CertificationBeijing Exhibition, Shanghai Exhibition5.After-sale Service6.FAQ I hope we can discussed online by whatsapp/wechat/Skype,To introduce more detail and answer your question.And we are seeking worldwide distributors.I believe Win-win is the best way for us.
3D CNC Router Wood Carving Machine3D CNC Router Wood Carving Machine1.Technical ParametersModelSD1325a)Control System Richauto DSP Handleb)Work Table Vacuum table with 5.5kw Vacuum Pumpc)Table Structure 8mm Steel Pipe Weldedd)Spindle 4.5KW Water Cooling Spindlee)Switch Vacuum Switchf)Motor/Driver Leadshine Stepper Motor(Servo Motor For optional)g)Rail 25mm PMI Square RailEfficient working area1300mm*2500mm*200mmMax carving speed15000mm/minTransmission typeX,,Y Gear Rack, Z Ball screwInverterSunfar Inverter/Delta InverterSupport file formatPLT , BMP , DXF , AL etcPower supplyAC380V/ 50HzHow to Use Design on the software,Then output.(Artcam,Ucancam,Type3)Input the file to control system by USB.(Syntec Control)Put the material on vacuum table,Move the Spindle to start point ,Then Click "Start".After a while,your product Finish.Main applications of cnc router : 1.Furniture industry: wooden doors, cabinet doors, board, office, solid wood furniture 2.Other wood products industry: speakers, game consoles cabinets, computer tables, sewing machine table, musical instruments, etc. 3.Board processing industry: insulation piece, plastic chemical products; PCB; fast train inside body, bowling tracks, stairs; compact grade laminate, epoxy resin, ABS, PP, PE and other cementitious mixtures s milling process 4..Decoration industry: folding screen, wave plates, large wall, advertising boards, signs and logo s processing.3.Features of MachineImported main parts for the machine,famous brand,stable personality.Dust cover for Z axis,Y guid and rack in the same side.Vacuum table have strong adsorbability,can adsorb different size materials.High speed and effciency,the engraving speed can reach to 20m/min,large cutting power not only to elaboratory carved a jagged,also smooth clear bottom.There is also any other size for a choice.Compamy Information14 years machine manufacture7 years export experience3 factories200 workersCE ISO CertificationBeijing Exhibition, Shanghai Exhibition5.After-sale Service6.FAQ I hope we can discussed online by whatsapp/wechat/Skype,To introduce more detail and answer your question.And we are seeking worldwide distributors.I believe Win-win is the best way for us.
3D CNC Router Wood Carving Machine3D CNC Router Wood Carving Machine1.Technical ParametersModelSD1325a)Control System Richauto DSP Handleb)Work Table Vacuum table with 5.5kw Vacuum Pumpc)Table Structure 8mm Steel Pipe Weldedd)Spindle 4.5KW Water Cooling Spindlee)Switch Vacuum Switchf)Motor/Driver Leadshine Stepper Motor(Servo Motor For optional)g)Rail 25mm PMI Square RailEfficient working area1300mm*2500mm*200mmMax carving speed15000mm/minTransmission typeX,Website:http://www.cncsudiao.com,Y Gear Rack, Z Ball screwInverterSunfar Inverter/Delta InverterSupport file formatPLT , BMP , DXF , AL etcPower supplyAC380V/ 50HzHow to Use Design on the software,Then output.(Artcam,Ucancam,Type3)Input the file to control system by USB.(Syntec Control)Put the material on vacuum table,Move the Spindle to start point ,Then Click "Start".After a while,your product Finish.Main applications of cnc router : 1.Furniture industry: wooden doors, cabinet doors, board, office, solid wood furniture 2.Other wood products industry: speakers, game consoles cabinets, computer tables, sewing machine table, musical instruments, etc. 3.Board processing industry: insulation piece, plastic chemical products; PCB; fast train inside body, bowling tracks, stairs; compact grade laminate, epoxy resin, ABS, PP, PE and other cementitious mixturesâ??s milling process 4..Decoration industry: folding screen, wave plates, large wall, advertising boards, signs and logoâ??s processing.3.Features of MachineImported main parts for the machine,famous brand,stable personality.Dust cover for Z axis,Y guid and rack in the same side.Vacuum table have strong adsorbability,can adsorb different size materials.High speed and effciency,the engraving speed can reach to 20m/min,large cutting power not only to elaboratory carved a jagged,also smooth clear bottom.There is also any other size for a choice.Compamy Information14 years machine manufacture7 years export experience3 factories200 workersCE ISO CertificationBeijing Exhibition, Shanghai Exhibition5.After-sale Service6.FAQ I hope we can discussed online by whatsapp/wechat/Skype,To introduce more detail and answer your question.And we are seeking worldwide distributors.I believe Win-win is the best way for us.
