SANDI 30KW DC to AC inverter with 120/240V split-phase off grid inverter with CSA/UL1741 Our SDP series Off Grid Pure sine wave inverter is one of the most advanced DC to AC conversion products in the world, it is suitable use for areas without electricity, vehicles, ships, solar energy, wind turbine and other renewable energy systems and etc, can supply power and provide guarantee effectively for the areas with traffic inconveniences, in the mountains, pastoral, border, island and other areas without electricity. It has the main advantages of high quality sine wave AC output, microcomputer control, humanness design, and it is high efficiency and low no-load loss, and no pollution. The inverter can also supply AC power to all kinds of electric equipment, air conditioners, motors, refrigerators, lights, TV, electric fans and other industrial power supply. Technical Features: 1. Using the sixth generation efficient IPM intelligent module from Japanese Mitsubishi, high efficiency and stable performance. It with powerful protection function, the protection for short circuit, over load, over temperature is more safe and reliable. Itâ??s service life can up to 15 years or more. 2. Intelligentized, modularized, simple structure design with powerful function. 3. Two kinds of start mode: Step-down Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. This function is very convenient for users and also reduce frequency converterâ??s usage, which reduced the cost of equipment investment, easy to connect wires and control. 4. The output frequency can be setting via LCD panel, itâ??s very convenient for customer. 5. The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy �±1%. 6. The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel. 7. Pure sine wave output. With good dynamic response less than 50MS, waveform distortion rate smaller, higher conversion efficiency and stable output voltage. 8. Low Frequency Transformer, which ensures that inverter has high efficiency. 9. High conversion efficiency, Max. Efficiencyâ?¥94%,if 48VDC input, the efficiency can more than 85%. 10. Adopts black pure aluminum radiator, which confirms the best radiating performance. 11. Powerful data display function. LCD can display the DC input voltage, output frequency, phase voltage, phase current, AC bypass input voltage, output power KWH, time and date, temperature, fault code display. 12. Wide input voltage can be set according to customerâ??s requirement. Input voltage range can be selected from 150-400V or 300-600V or 400-800V. 13. Wide input voltage can work without battery and solar charge controller, save more cost and With MPPT wide voltage input function, maximum use of solar power.
Our SDP series Off Grid Pure sine wave inverter is one of the most advanced DC to AC conversion products in the world, it is suitable use for areas without electricity, vehicles, ships, solar energy, wind turbine and other renewable energy systems and etc, can supply power and provide guarantee effectively for the areas with traffic inconveniences, in the mountains, pastoral, border, island and other areas without electricity. It has the main advantages of high quality sine wave AC output, microcomputer control, humanness design, and it is high efficiency and low no-load loss, and no pollution. The inverter can also supply AC power to all kinds of electric equipment, air conditioners, motors, refrigerators, lights, TV, electric fans and other industrial power supply. Technical Features: 1. Using the sixth generation efficient IPM intelligent module from Japanese Mitsubishi, high efficiency and stable performance. It with powerful protection function, the protection for short circuit, over load, over temperature is more safe and reliable. It's service life can up to 15 years or more. 2. Intelligentized, modularized, simple structure design with powerful function. 3. Two kinds of start mode: Step-down Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. This function is very convenient for users and also reduce frequency converter's usage, which reduced the cost of equipment investment, easy to connect wires and control. 4. The output frequency can be setting via LCD panel, it's very convenient for customer. 5. The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy ±1%. 6. The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel. 7. Pure sine wave output. With good dynamic response less than 50MS, waveform distortion rate smaller, higher conversion efficiency and stable output voltage. 8. Low Frequency Transformer, which ensures that inverter has high efficiency. 9. High conversion efficiency, Max. Efficiency 94%,if 48VDC input, the efficiency can more than 85%. 10. Adopts black pure aluminum radiator, which confirms the best radiating performance. 11. Powerful data display function. LCD can display the DC input voltage, output frequency, phase voltage, phase current, AC bypass input voltage, output power KWH, time and date, temperature, fault code display. 12. Wide input voltage can be set according to customer's requirement. Input voltage range can be selected from 150-400V or 300-600V or 400-800V. 13. Wide input voltage can work without battery and solar charge controller, save more cost and With MPPT wide voltage input function, maximum use of solar power.
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Technical Features: 1, The core components are all imported, adopting the sixth generation IPM module from Mitsubishi, which has stable performance, long service life, strong protection functions and convenient replacement and maintenance. 2, Adopt the central processor DSP28335 chip from American TI Company, respond quickly and accurately, and provide stable and clean power for the load to provide protection. 3, The whole machine adopts modular design and plug-in design, which is convenient for maintenance. 4, According to the product configuration conditions, adjustment the system usage mode: DC(Battery/Solar) priority or AC mains bypass priority can be set. 5, Two kinds of start mode: Reduction Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. 6, The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy �±1%. 7, The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel. 8, Output AC Power is suitable for all types of electrical equipment, CNC machines, electric tools, motors, pump and air conditioner etc. It has higher efficiency and higher capability of driving load. 9, Humanized safety design, using isolation transformer design, input and output are completely electrically isolated, input and output are equipped with circuit breakers, which saving costs for the user and easy to installation, the electric parts are completely closed to prevent electric shock. 10, Using SVPWM space vector algorithms, high conversion efficiency, high instantaneous power and low losses conversion efficiency up to 94%. 11, Powerful data display function. LCD + LED display, can display input and output voltage, current, KWH, fault display, convenient for customers to quickly find faults and guide maintenance. 12, The controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of photovoltaic modules and batteries 13, Solar controller adopt IGBT Modular design ensure stable and efficiency performance of solar controller and solar power system 14, The controller has perfect battery protection function and with multi-stage charging technology to improve battery life 35% at least 15, Fully enclosed duct design and high-speed fan for cooling makes the controller working under harsh environments 16, The controller has power generation statistics and real-time power curve function, so we can know power generating information at any time 17, Colorful LCD display, touching key and multi-language option makes the HMC (Human Machine communication) easy and convenient. 18, The controller also has temperature compensation function and RTC real time clock function,
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75200 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Herbal tea ingredients, spices, herbs 1. chamomile fine cut 2. butterfly pea flower blue, 3. moringa 4. hibiscus c & s. 5. mint leaves c & s 6. lemongrass c & s. 7. jasmine 8. lemon, ginger 9. clove whole 10. anise seed 11. cassia alta 12. seena 13. lavender buds 14. holy basil 15. elderberry 16. schizandra berry. 17. cardamom 18. marigold petals 19. licorice 20. rose buds. 21. star anise whole or cracked. 22. orange peel c & s. 23. lemon peel c& s. 24. corn flower petals �¢?? blue..Bulk export, manufacturing, contract manufacturing, product sourcing, private label packaging, customized packaging
* Quantity MIN 50,000MT x 12 months * Origin: German Origin Specifications: The products are in accordance with the specifications requested by The Buyer or presented by The Seller. * Payment: By MT103/760 * Price/Commissions: Final price to Buyer is the Gross, including all commissions. * Payment is then made by Seller, who carries out all commissions transfers. *Contract: 12 Months with possible rollovers. * Inspection: SGS or similar * CIF SBLC PROCEDURE - Summary of our procurement process:- 1. Buyer issue an RFP (Per attached template -w- specification sheet) 2. We issue a commercial offer with all relevant tacit data 3. Buyer returns signed commercial offer in conjunction with a Banker Signed RWA letter (Verbiage will be attached in the commercial offer) 4. Seller issues the Sales & Purchase Agreement 5. The Contract is formalized and lodged with respective bankers 6. Buyer's Banker issues a Pre-Advice MT799 7 Seller issues the Price Lock Notice (a discount is set on this day per the Platts Assessment of the day) 8. Buyer Banker issues the collateral (MT760) 9. Seller's Banker issues 2% Performance Bond 10. Seller charters the vessel/barges 11 Seller berths the vessel/barges 12. Seller loads the vessel/barges 13. Seller issues Product & Shipping Documentation (Digitally AND via courier) 14. Vessel/Barge departs for destination
Process Denim Type Rigid (Non-Stretch) Weight 13 oz Weave 3/1 Twill Composition Cotton Color Blue, Black, Blue Black
Design no : IRC-13 FT Quality : DURRIES Material : Denim Price : USD 8 / sq mtr(F.O.B.) Weight : 2.00 kg / sq mtr Size : 2.0 x 3.0
We offer to supply 100% Coconut Shell Charcoal Briquettes , Hexagonal shape and the specifications as follows. 1.Color - Black 2.Odor - Odor less 3.Smoke - Smokeless 4.Shape - Hexagonal 5.Size - 50mm Dia X 125mm Length 6.Weight - 250 to 350 Grams 7.Fixed Carbon - 55 to 60% 8.Ash - 25% 9.Volatile Matters - 14% 10.Moisture - 5% max 11.Energy - 6500 Kcal/kg 12.Heat Content - 350C 13.Ash Colour - White 14.Ignition Time - 10 Min Max 15. Burning Time - 4 to 5 Hrs.
Reesha Gold Sona Masoori Indian Rice, Specifications: Package Quantity: 1, Product Size: 18 KG, Grains Rice Type: Basmati Rice, Packaged Food Brand: Reesha Gold Brand, Purity â?? 95.00%, Natural Admixture â?? 5.00%, Average Grain Length â?? 5.20 MM, Moisture â?? 13% Max, Broken Grain â?? 2% Max, Damage/Discolor Grain â?? 2% Max, Immature Grain â?? 2% Max,
Item Specifications Available options Product Personalized Paper Napkins Printed logo color 2 1 or 2 color logo printing Material Virgin pulp Virgin, Mixed, Recycled pulp Napkin size: 33cm x 33cm 33cm, 30cm, 25cm, 24cm, 40cm etc. Ply 1ply 1ply - 4ply Grammage 18gsm//m2 14gsm-40gsm/m2 Folded 1/8fold 1/4, 1/6, 1/8, 1/12, 1/16, dispenser fold After folded size 16.5cm x 8.3cm Package 400pcs/pack, 20packs/carton Any kind of package as per your requirement Carton size 34.7cm x 34cm x 65.5cm G.W. 16kg/carton Loading qty: 900ctns/40ft HQ, 780ctns/40ft GP 390ctns/20ft GP
Letter Magnetic Board Material ABS Size 12.3 x 10 inch Packaging 25pcs/carton Packaging Size 55 x 33 x28cm Color Black, Blue, White(can be customized) Packing Weight 22.6kg
Name: organic dried cloves Colour: natural brown Grace: 1 and 2 Moisture: Max 13 % Additive: 1% MAX Shelf life: 2 year
Specifications: Product Type: Moringa-oleifera. Feature: Low-Fat, Normal, Sugar-Free. Style: Dried nut. Moisture: 13% max. Impurity: 1% max.
2.Arabica coffee bean -Grade 1, screen 16 Moisture :12.5% max. Admixture :0.5% max Black & Broken beans : 2% Above screen 16 : 90% 3.Arabica/ coffee beans Grade 2, Screen 13 Moisture: 13% max. Admixture: 1% max. Black & Broken beans: 5% max. Above Screen 13: 90% ARABICA AND ROBUSTA COFFEE BEANS , GREEN COFFEE BEANS MOISTURE: 13% MAX. FOREIGN MATTER: 0.5% MAX BLACK & BROKEN:2% MAX. ON SCIEVE SCREEN 16: 90% MIN. 1.ROBUSTA COFFEE SCREEN 13, GRADE 2 SPECIFICATION: MOISTURE: 13% MAX. FOREIGN MATTER: 0.5% MAX. BLACK AND BROKEN: 5% MAX. ON SCIEVE SCREEN 13: 90% MIN. 2.ROBUSTA COFFEE SCREEN 16, GRADE 1SPECIFICATION: MOISTURE: 13% MAX. FOREIGN MATTER: 0.5% MAX. BLACK AND BROKEN: 2% MAX. ON SCIEVE SCREEN 16: 90% MIN 1.Arabica coffee grade 1, screen18 Moisture: 12.5% max Admixture :0.5% max Black & Broken beans: 2% Above screen 18: 90%
Available for sale is top grade Arabica Coffee Beans, Robusta Coffee Beans, Green Coffee Beans , now available at affordableprices , best market conditions ARABICA AND ROBUSTA COFFEE BEANS , GREEN COFFEE BEANS MOISTURE: 13% MAX. FOREIGN MATTER: 0.5% MAX BLACK & BROKEN:2% MAX. ON SCIEVE SCREEN 16: 90% MIN. 1.ROBUSTA COFFEE SCREEN 13, GRADE 2 SPECIFICATION: MOISTURE: 13% MAX. FOREIGN MATTER: 0.5% MAX. BLACK AND BROKEN: 5% MAX. ON SCIEVE SCREEN 13: 90% MIN. 2.ROBUSTA COFFEE SCREEN 16, GRADE 1SPECIFICATION: MOISTURE: 13% MAX. FOREIGN MATTER: 0.5% MAX. BLACK AND BROKEN: 2% MAX. ON SCIEVE SCREEN 16: 90% MIN 1.Arabica coffee grade 1, screen18 Moisture: 12.5% max Admixture :0.5% max Black & Broken beans: 2% Above screen 18: 90%
