Aluminum composite panel production line
Spiral wound gasket Got-400 spiral wound gasket is accumulated, hovered and wound, and spot welded beginning and end terminal by v-shaped or w-shaped stainless steel and non metal filler, which has good compression elasticity, and is suitable for the sealing parts with temperature and pressure altering violently. It is a static sealing parts used for such flange connecting joints as pipeline, valve, bump, heat exchanger, tower, manhole, and hand hole, etc. It is widely applied in departments as petrochemical, mechanical, electric power, metallurgy, boat building, medical, atomic energy, and aerospace, etc. Ansi b 16.20mss sp-44api 605dinjisjpibs 1560jg/tgb/thgsh, etc.
Inner and outer ring of swg Got-400r metal flat gasket can also be processed into the inner and outer ring of the spiral wound gasket. We will punch the gasket that with the size smaller than 8fª by punching machine, and for the one that with large size by lathe. If for the expensive material as ss304, ss316, etc. As long as the sealing plane is not over wide, we will basically use the special ring rolling machine, process by the wire rod, to largely cut cost. The carbon steel outer ring can be coated with zn, white zn, or paint-drying, and the typing will be according to the standards or the demands. Product structure: The metal interface flat gasket, choose kinds of solid metal, mechanically cut and processed into kinds of metal sealing gaskets by high precision nc lathe, suitable for the sealing parts of pressure container, valve, cylinder head with high temperature, high pressure, and strong corrosion. General characteristic is installation area small and preload pressure high. Got-400r metal flat gasket can also be processed into the inner and outer ring of the spiral wound gasket. Got self design and manufacture the ring processing special equipment, outer ring trench cutter, and inner ring chamfering machine. Comparing with the traditional lathe, it is high efficient, low cost, and need no special fixture. Inventory product: Size: Asme b 16.20 1/2fª ~ 24fª 150lb, 300lb, 600lb, 900lb Other sizes or standards on require. Material: Carbon steel, zinc plating, or without zinc plating Ss304, ss304l, ss316, ss316l The following special material on require: Ss321, ss317l, duplex 31803, Ti, ni, inconel, monel, hastelloy, and zr, etc
Kammprofile gasket Got kammprofile gasket , generally processed to be concentric groove in the two faces of the stainless steel flat gasket by precise lathes. According to the different medium, w can choose flexible graphite, ptfe, non-asbestos, or other soft metal, to sick to the two faces of the gasket. It can directly be used without sealing layer, and the effect is good. But under the high pressure occasion, it will be easy to do damage to the surface of the flange. 410 basic type kammprofile gasket 410l kammprofile gasket with outer ring (integral type) 410lm kammprofile gasket with outer ring (split type) Model 410lm split type metal toothed gasket with outer ring, can choose richer metal, e.G. Carbon steel, as the outer ring, and the outer ring thickness can be 1.5mm, more flexible and economic than the integral type 410l, and the lining metal can be repeatedly used. Product application: Got toothed combination gasket is the first choice gasket under relatively low preload power, the soft surface of the sealing layer can avoid the direct touch between metal and metal, which is combined reliably and compactly, to protect the metal flange from damaged, even under extremely high load. The toothed combination gasket is especially suitable for the flange connection in thermal exchanger, container, and reaction vessel under high temperature, high pressure, and the working condition altering occasions. It is an ideal substitution for traditional metal jacketed gasket. Operating pressure range: 6.4~25mpa Overlaying material: Flexible graphite, asbestos plate, non-asbestos plate; Ptfe, mica plate, lead, etc. Generally the thickness of the dual overlaying is 0.5mm
Ring joint gasket Got-450 ring joint gasket chooses solid metal with kinds of materials, and is mechanically cut and processed into metal sealing gaskets with kinds of forms by high precision nc lathe. It is suitable for the sealing part of pressure container, valve, and cylinder head with high temperature, high pressure, and strong corrosion. General characteristic is installation area small and preload pressure high. Metal flat gasket Metal elliptic gasket Metal aniseed gasket Rx type metal gasket Bx type metal gasket Special-shaped metal gasket
Reinforced (non-)asbestos beater sheet Got-633 is made of 633-1 non-asbestos beater sheet inner lined with metal truss plate (generally the carbon steel with 0.2~0.25mm thickness). It is extensively applied in manufacturing various automobile and motor gaskets. It is an ideal material that will substitute the traditional asbestos gaskets. The product has excellent performance in self expansion, high resilience and long lifespan, etc. Mainly applied in automobile farming machine, motorcycle and engineering etc., it is also can be used in high strength gaskets and cylinder gaskets etc. Product structure: Got-633 truss plate reinforced asbestos beater sheet If stored for a long time, the asbestos will have certain corrosion to the inner lined metal.
Cnc machining parts Cnc is the removal of material though the use of automated computer controlled machine tools to remove unwanted materials from a piece of raw material such as bar stock or plate to get a refined finished shape. Our main activities are manufacturing general tooling, fixtures, press tools, high precision and cnc machining parts, no matter small or medium volumes, local or worldwide customers, providing cost effective machined parts that meet specification on time. At ningbo cnc machining co, ltd, we use cnc lathes, cnc vertical mills, horizontal mills and drilling machines to remove steel, iron, brass, aluminum, copper, stainless steel, phenol, delrin, nylon and plastics.More equipments inculde circular grinding, centreless grinding, surface grinding, digital wire cutting and threading machine. We also machine precision finished parts from near net shapes such as forgings, castings, extrusions, die-castings, investment castings and flame cut blanks to make production quantities of precision machined parts.For example, pump body, pump impeller ect
Pump parts Pump parts and accessories are components and devices used in the construction of pumps. Pump parts and accessories include gas pump parts, water pump parts, and sump pump parts. Others are the shaft and impeller. Based on our die casting workshop and precision maching equipments, we manufactures pump parts, such as pump body, pump impeller ect. The materials can be cast iron or nodular cast iron for the pump body;plastic, cooper , cast iron or stainless steel for impeller.
Ptfe gasket 1) sealing gasket for pumps and pipes, etc. 2) all sizes are available 3) new molds can be made according to customers' requirements 4) high chemical properties 5) wide temperature range from -180ípc to +260ípc 6) has the lowest coefficient of friction of all the known solid materials 7) not aging 8) nonstick All sizes are available on costomers' request
Ptfe gasket 1) sealing gasket for pumps and pipes, etc. 2) all sizes are available 3) new molds can be made according to customers' requirements 4) high chemical properties 5) wide temperature range from -180c to +260c 6) has the lowest coefficient of friction of all the known solid materials 7) not aging 8) nonstick All sizes are available on costomers' request
P.C. Board piercing system The system employs hydraulic pressure for activating the platen to knock out. It is totaly different from the conventional mechanical structure, and can prevent the board and the dies from being heavily impacted by the press, thus minimize the breaking of pierce pin and prolong the dies service life. To collocate quick die change system can shorten the time of die change and ensure the operation safety.
Quick die change system Quick die change system can help to change die / mold in a short time. It replaces the traditional method which used the screw to fix the die/mold. To insure the safety of operation, the movement between each equipment will be pined down mutually.It has the function of inspection pressure and can be interlocked with the machine
Mold changer system Mold changer system is used on press machine and injection molding machine. It help die/mold to move in and out of the machine on the rail. It have the inspection function of mold loading position, mold change, mold-move-in position, mold-centered position
Block machine Parameter: Framework dimension: 680*4, 150*2, 900 mm Pallet/plate size (mm): 1, 100*700*25 (bamboo) 1, 100*700*20 (pvc) Weight: 11, 100 kg Vibration frequency: 50-90 hz Max excited force: 90 kn Molding cycle: 15-20 days Installed capacity: 32.8 kw Product discriptions: 1. Unique designed storing system: double hopper design makes it possible that aggregates can be supplied efficiently and uniformly to avoid pockety. 2. Multi-vibration system: it can send the vibration force to every parts of the mould box synchronously to improve the durability of blocks/bricks. It adopts systematic design of machine, electricity, liquid and computer to meet the big table work.Requirement. The vibration force & frequency are adjustable according to different materials and craftwork procedures: low frequency-adding materials and high frequency-molding. 3. Control system: digital location sensor is used to make sure the accuracy of every operation. Plc photoelectric real-time control system can protect the equipment to work normally. It is high technology researched by ourselves including touch operation and patent oil pump protection. It is more durable. It is easy for the users to operate with the help of real-time prompt facility. 4. Autodiagnostics: real-time malfunction self-diagnosis facility can give an alarm of fault resolution timely. It is combined with the remote control system by telephone lines to make self-diagnosis. Framework dimension: 680*4, 150*2, 900 mm Weight: 11, 100 kg
Concrete block making machine Parameter: Max block dimension (mm): 1000*600*40~200 Dimension: 6, 900*3, 800*2, 660 mm Pallet/plate size (mm): 870*870*25 (bamboo) 870*870*20 (pvc) Power: 33.7 kw Weight: 10, 000 kg Vibration frequency: 50-90 hz Max excited force: 80 kn Molding cycle: 15-20 days Installed capacity: 31.7 kw Product discriptionsú¦ 1. Integrative storage and distribution system makes dosing precision and density of bricks/blocks possible. 2. The specific design of feeding: it adopts the positive and compulsory arch acentric feeding technology. Under the help of material distribution bar (that is, mixer fork), it can setting the material into the mould box quickly and uniformly. 3. Integrated oil circuit system: it is designed by international standards, high durability, weather-resistant, low energy consumption and uses imported units. The reasonale design of the oil circuit can make full use of the energy consumption to 90%. 4. Computer control system: it is plc control system imported, with man-machine interface, liquid crystal display, intelligent control, malfunction self-diagnosis and remote control. It is very simple to operate and safe to use. 5. Durable design: it applies specific welding craftwork to make it more consistent and durable. 6. Combinatory sencodary material distributor: it can be assembled variously to meet different requirements range from 6 cm to 9 cm, single color or double colors. Dimension: 6, 900*3, 800*2, 660 mm Weight: 10, 000 kg
Specification: Purpose Grit No. Chemical composition (%) Al203 Fe203 Si02 Ti02 F4-F80 95.0Min 0.3max 1.5max 3.0max For abrasive F90-F150 94.0Min 0.3max 1.5max 3.0max F180-F240 93.0Min 0.3max 1.5max 3max P4-P80 95.0Min 0.3max 1.5max 3.0max For abrasive P90-P150 94.0Min 0.3max 1.5max 3.0max P180-P240 93.0Min 0.3max 1.5max 3max For abrasive W1-W63 92.5Min 0.5max 1.8max 4.0max 0-1mm 94.5Min 0.3max 1.5max 3.0max 1-3mm 95.0Min 0.3max 1.5max 3.0max For refractory 3-5mm 95.0Min 0.3max 1.5max 3.0max 5-8mm 95.0Min 0.3max 1.5max 3.0max 8-12mm 95.0Min 0.3max 1.5max 3.0max 0-3mm 94.0Min 0.3max 1.5max 3.0max 0-5mm 94.0Min 0.3max 1.5max 3.0max For refractory 0-10mm 94.0Min 0.3max 1.5max 3.0max 0-25mm 94.0Min 0.3max 1.5max 180mesh-0 93.5Min 0.5max 1.8max 3.5max For refractory 220mesh-0 93.5Min 0.5max 1.8max 3.5max 320mesh-0 93.5Min 0.5max 1.8max In 1MT Big Bag ,In 25kg plastic woven bag,40 bags in 1MT Big Bag
Specification: Chemical composition(%) Al203 Zr02 Ti02 Si02 ZA40 50í¬60 38í¬44 1.0 Max 0.5Max ZA25 68í¬72 24í¬30 1.0 Max 0.5Max In 1MT Big Bag, In 25kg plastic woven bag, 40 bags in 1MT Big Bag
Purpose Specification Chemical composition(%) Al203 Nao Cao F12-F80 99.0Min 0.5Max 0.4Max For abrasive F90-F150 98.5Min 0.6Max 0.4Max F180-F240 98.2Min 0.7Max 0.4Max For abrasive W1-W63 97.5Min 0.8Max 0.5 Max 0-1mm 99.0Min 0.5Max 0.4Max 1-3mm 99.0Min 0.5Max 0.4Max For Refractory 3-5mm 99.0Min 0.5Max 0.4Max 5-8mm 99.0Min 0.5Max 0.4Max 8-12mm 99.0Min 0.5Max 0.4Max For Refractory 0-180mesh 98.5Min 0.5Max 0.4Max 0-220mesh 98.5Min 0.5Max 0.4Max 0-320mesh 98.5Min 0.5Max 0.4Max In 1MT Big Bag, In 25kg Plastic woven bag, 40 bags in 1MT Big Bag
Specification Chemical composition(%) Al203 Fe203 Si02 Ti02 TC 0-1mm 97.5min 0.3max 0.5max 1.0max 0.1max 1-3mm 97.5min 0.3max 0.5max 1.0max 0.1max 3-5mm 97.5min 0.3max 0.5max 1.0max 0.1max 5-8mm 97.5min 0.3max 0.5max 1.0max 0.1max 8-12mm 97.5min 0.3max 0.5max 1.0max 0.1max 180mesh-0 97.5min 0.3max 0.5max 1.0max 0.15max 220mesh-0 97.5min 0.3max 0.5max 1.0max 0.15max 320mesh-0 97.5min 0.3max 0.5max 1.0max 0.15max In 1MT Big Bag, In 25 plastic woven bag,40 bags in 1MT Big Bag
Specification: Grit No. Chemical composition (%) Al203 Fe203 Si02 Ti02 F4-F100 97.5 0.15 0.5 1.5 F120-F240 97 0.2 0.8 1.5 P4-F100 97.5 0.15 0.5 1.5 P120-P240 97 0.2 0.8 1.5 In 1MT Big Bag, In 25kg plastic woven bag,40 bags in 1MT Big Bag
